Whirlpool GB2SHDXTS01, GX5FHDXTB01, GX5FHDXTB11, GX5FHDXTL01, GX5FHDXTL11 Owner’s Manual

...

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING, please visit our website at www.whirlpool.com for additional information. Ifyou still need assistance, call us at 1-800-253-1301.In Canada, visit our website at www.whirlpool.ca or call us at 1-800-807-6777.

You will need your model and serial number located on the right-hand side of the refrigerator interior.

Para obtener acceso a "lnstrucciones para el usuario del refrigerador" en espaSol, o para obtener informaci6n adicional de su producto, visite: www.whirlpool.com

Tenga listo su nOmero de modelo completo. Puede encontrar su nOmerode modelo y de serie en la etiqueta ubicada al lado derecho del interior del refrigerador.

Table of Contents /Table des matibres

REFRIGERATOR SAFETY ................................................................... 1

INSTALLATION INSTRUCTIONS ....................................................... 2

REFRIGERATOR USE ....................................................................... 12

REFRIGERATOR CARE ..................................................................... 14

TROUBLESHOOTING ........................................................................ 15

WATER FILTER CERTIFICATIONS .................................................. 17

PRODUCT DATA SHEETS ................................................................ 18

WARRANTY ........................................................................................ 19

SleCURITle DU RleFRIGleRATEUR ................................................... 20

INSTRUCTIONS D'INSTALLATION ................................................. 21

UTILISATION DU RleFRIGleRATEUR ............................................... 31

ENTRETIEN DU RleFRIGleRATEUR ................................................. 33

DlePANNAGE ...................................................................................... 35

FEUlLLES DE DONNleES SUR LE PRODUIT .................................. 38

GARANTIE .......................................................................................... 39

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

W10137645A

iMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the refrigerator, follow basic precautions,

including the following:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline, away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker kit ready models only).

SAVE THESE INSTRUCTIONS

ProperDisposal ofYour Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of your old refrigerator, please follow these instructions to help

prevent accidents.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily climb inside.

When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.

Remove the Packaging

• Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water and dry.

• Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For more information, see "Refrigerator Safety."

• Properly dispose of packaging.

Clean Before Using

After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in "Refrigerator Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when removing them to avoid impact from dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator. Failure to de so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a 1/211 (1.25 cm) space at the top and behind the refrigerator. If your

refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a fixed wall, leave 21/2'' (6.3 cm) minimum on the hinge side (some

models require more) to allow for the door to swing open. NOTE: It is recommended that you do not install the refrigerator

near an oven, radiator, or other heat source. Do not install the refrigerator in a location where the temperature will fall below 55°F

(13°C).

_/2"(1.26crn)/

][

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn the refrigerator to OFR Depending on your model, turn the freezer control to the word OFF, or press the Freezer down arrow touch pad until a dash (-) appears in both the

Freezer and Refrigerator displays as shown. Disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the

temperature controls to the desired setting. See "Using the Controls."

21/2 '' (6.3 cm)

®0® 00®

co_ FREEZER COLDER RecommendedSetti_gs:4 col_ REFRI6_RATORco_

ColdestSettings:7

_ 7 . i'_ _ • , _ .

_le_ ° _O__ _(i_em_ts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • %" Nut driver

• 7Ae"and W' Open-end or two • %" Drill bit adjustable wrenches

• Cordless drill

IMPORTANT:

• All installations must meet local plumbing code requirements,

• Do not use a piercing-type or 3/_6"(4.76 mm) saddle valve which reduces water flow and clogs more easily.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain

above freezing.

Water Pressure

A cold water supply with water pressure of between 35 and 120 psi (241 and 827 kPa) is required to operate the water

dispenser and ice maker. Ifyou have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 35 and 120 psi (241 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa). If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

• If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See "Water Filtration System."

If you have questions about your water pressure, call a licensed, qualified plumber.

Read all directions before you begin. IMPORTANT: If you turn the refrigerator on before the water line is

connected, turn the ice maker OFE

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Find a W' to 1W' (12.7 mm to 3.18 mm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe,

• Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve,

Determine the length of copper tubing you need. Measure from the connection on the lower right rear of refrigerator to

the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use W' (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

Using a cordless drill, drill a W' hole in the cold water pipe you have selected.

....... A

D E

F G

A. Cold water pipe

B. Pipe clamp C. Copper tubing

D. Compression nut

E. Compression sleeve F. Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the V4"drilled hole in

the water pipe and that the washer is under the pipe clamp, Tighten the packing nut, Tighten the pipe clamp screws slowly

and evenly so the washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and turn ON the main water supply, Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe.

Connect to Refrigerator

Depending on your model, the water line may come down from the top or up from the bottom. Follow the connection instructions

for your model.

Style 1

1. Remove plastic cap from water valve inlet port. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not

overtighten. Confirm copper tubing is secure by pulling on copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a "P" clamp.

Using an adjustable wrench, hold the nut on the plastic water line to keep it from moving. Then, with a second wrench turn

the compression nut on the copper tubing counterclockwise to completely tighten. Do not overtighten.

A. Plastic water line D.Copper tubing

B. Water valve inlet port E. "P" clamp

C. Compression nut

6. Check connection by pulling on copper tubing. Attach copper tubing to refrigerator cabinet with a "P" clamp. Turn on water

supply to refrigerator and check for leaks. Correct any leaks.

Complete the Installation

A. Copper tubing D. Compression sleeve B. "P" clamp E. Water valve inlet port C. Compression nut

3. Turn on water supply to refrigerator and check for leaks. Correct any leaks.

Style 2

1. Create a service loop (minimum diameter of 2 ft [61 cm]) with the copper tubing. Avoid kinks when coiling the copper

tubing.

2. Remove the plastic cap from water valve inlet port. Place a compression nut and sleeve on the copper tubing.

3. Insert the end of the copper tubing into the water valve inlet port. Shape tubing slightly so that the tubing feeds straight into the port to avoid kinks.

4. Slide the compression nut over the sleeve and screw into the water valve inlet port.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1. Plug into a grounded 3 prong outlet. NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely fill the ice container.

A. Plastic water tubing C. Compression nut

B,Sleeve D. Copper tubing

TOOLS NEEDED: %6", %", 1/4"hex-head socket wrench, a #2 Phillips screwdriver, and a flat-blade screwdriver.

IMPORTANT:

• Your refrigerator may have a standard reversible refrigerator door (Style 1) with either a freezer door or freezer drawer, or French doors (Style 2). Follow the instructions specific to the door style of your model.

• All graphics referenced in the following instructions are included later in this section after "Final Steps." The graphics shown for the standard door (Style 1) are for a right-hand swing refrigerator (hinges factory installed on the right).

• If you only want to remove and replace the doors see "Remove Doors and Hinges" and "Replace Doors and Hinges."

• Before you begin, turn the refrigerator control OFF, and remove food and adjustable door or utility bins from the doors.

3. Remove the parts for the top hinge as shown in Top Hinge graphic. Lift the refrigerator door free from the cabinet.

4. Remove the center hinge pin and remove the hinge screws as shown in the Center Hinge graphic. Lift the freezer door free

from the cabinet.

5. Remove the parts for the bottom hinge as shown in Bottom Hinge graphic.

Style 2-French Doors

Install and Remove Refrigerator Door Handles

Style 1-Standard Door

1. Place handle on the door or drawer as shown. Using a Phillips

screwdriver, attach the handle to the door with the handle screws.

2. Place the handle trim pieces on the handle ends as shown. Using your hand, apply firm pressure on the face of the trim and slide the trim piece toward the center of the handle.

3. To remove handles, reverse directions.

Style 2-French Doors

1. Using a %2" Allen wrench, loosen the two set screws located on the side of each handle. See Graphics 1 and 2.

2. Pull the handle straight out from the door. Make sure you keep the screws for reattaching the handles.

3. To replace the handles, reverse the directions.

Remove Door and Hinges

Style 1-Standard Door

Hex-Head Top Hinge Screw

Freezer drawer models

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator door closed until you are ready to lift it free from the cabinet.

NOTE: Provide additional support for the door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

3. Remove the parts for the top hinge as shown in Top Hinge graphic. Lift the refrigerator door free from the cabinet.

4. Remove the parts for the bottom hinge as shown in Bottom Hinge graphic.

Freezer door models

1. Unplug refrigerator or disconnect power.

2. Keep the freezer door closed until you are ready to lift it free from the cabinet.

NOTE: Provide additional support for the door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

Electrical Shock Hazard

Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the refrigerator door while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are working.

3. Starting with the right-hand side door, remove the parts for the top hinge as shown in Top Hinge graphic. Lift the refrigerator

door from the bottom hinge pin.

4. Removethe shim (on some models) from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic.

5. Before removing the left-hand side door, disconnect the wiring plug located on top of the top hinge by wedging a flat-blade screwdriver or your fingernail between the two sections. See Wiring Plug graphic.

NOTE: The green, ground wire remains attached to the hinge.

6. Remove the parts for the left-hand side door top hinge as shown inthe Top Hinge graphic. Lift the door from the bottom hinge pin.

NOTE: On some models, remove the shim from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic.

Reverse Door - Standard Door (optional)

IMPORTANT: If you want to reverse your door so it opens from the opposite side, follow these steps. Ifyou are not reversing the

door, see "Replace Door and Hinges."

Door Stop Screw

Flat-Head Handle Screw

Cabinet

1. Remove hinge screws from handle side and move them to opposite side. See Graphic 1-1.

2. Remove cabinet hinge hole plugs from cabinet top and move them to opposite side hinge holes as shown in Graphic 1-2.

Door Handle Seal Screw Front

Cabinet Hinge Hole Plug

Refrigeratordoor

1. Removetherefrigeratorhandleassemblyasshownin Graphic2,Keepallpartstogether.

2. Removedoorhandlesealscrewfront,Movetooppositeside ofrefrigeratordoorasshowninGraphic5.

3. Removethedoorstop,Moveittotheoppositesideofthe refrigeratordoorasshowninGraphic3,

4. Attachrefrigeratorhandleonoppositesideoftherefrigerator doorwiththetwoscrewsasshowninGraphic2,Replace

handletrimasshown.

5. Tightenallscrews.Setasidethedooruntilhingesandfreezer compartmentdrawerareinplace,

Freezerdoor

1. RemovefreezerhandleassemblyasshowninGraphic5-1. Keepallpartstogether.

2. Removefreezerdoorhandlesealscrew.Movetoopposite sideoffreezerdoor.

3. Removedoorstop,Movetooppositesideoffreezerdooras showninGraphic4.

4. Attachhandletooppositesideoffreezerdoor.

5. Tightenallscrews.Setasidedooruntilbottomhingeis installedonproduct,

Replace Door and Hinges

Style 1-Standard Door NOTE: Graphics may be reversed if door swing is reversed.

Freezer drawer models

1. Replace the parts for the bottom hinge as shown. Tighten screws,

NOTE: Provide additional support for the door while the hinges are being moved. Do not depend on the door gasket

magnets to hold the door in place while you are working.

2. Assemble the parts for the top hinge as shown in Top Hinge graphic. Do not tighten screws completely.

3. Adjust the door so that the bottom of the refrigerator door is aligned with the top of the freezer drawer. Tighten all screws,

Freezer door models

1. Replace the parts for the bottom hinge as shown. Tighten screws. Replace the freezer door.

NOTE: Provide additional support for the door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

2. Assemble the parts for the center hinge as shown in the Center Hinge graphic, and tighten all the screws. Replace the

refrigerator door.

3. Assemble the parts for the top hinge as shown in the Top Hinge graphic. Do not tighten the screws completely.

4. Adjust the doors so that the bottom of the refrigerator door is aligned with the top of the freezer door. Tighten all screws.

Style 2-French Doors

1. Assemble the parts for the top hinges as shown in Top Hinge graphic, Do not tighten the screws completely.

2. Replace the parts for the bottom hinges as shown in Bottom Hinge graphic. Tighten screws, Replace the refrigerator doors.

NOTE: Provide additional support for the refrigerator doors while the hinges are being moved. Do not depend on the door

gasket magnets to hold the doors in place while you are working.

3. Align each door so that the bottom of the refrigerator door aligns evenly with the top of the freezer drawer. Tighten all screws.

4. Reconnect the wiring plug on top of the left-hand side refrigerator door.

5. Replace the top hinge covers.

Remove and Replace Freezer Drawer

IMPORTANT:

• Two people may be required to remove and replace the freezer drawer.

• All graphics are included later in this section after "Final Steps."

Remove Drawer Front

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the drawer front. See Drawer Front Removal graphic,

NOTE: Loosen screws three to four turns. Keep the screws in the drawer front,

3. Lift drawer front upward and off the screws, See Drawer Front Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the freezer compartment. Insert

the screws in the top of the drawer front into the slots in the drawer brackets. See Drawer Front Replacement graphic.

2. Pull the drawer brackets toward you to insert the two screws in the bottom of the drawer front into the brackets. See

Drawer Front Replacement graphic.

3. Completely tighten the four screws.

Final Steps

1. Check all holes to make sure that hole plugs and screws are in place. Reinstall top hinge cover as shown in Top Hinge graphic,

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death, fire, or electrical shock.

2. Plug in refrigerator or reconnect power.

3. Return all removable door parts to door and food to

refrigerator.

Standard Door - Freezer Door

iiiiiiiiii_

HHHHH HHHHH

HHHHH_

;iiiiiiii_

Bottom Hinge

A. Hinge Pin Shim (on some models) B. Bottom Hinge

C. 3/_,,Hex-Head Hinge Screws D. Bottom Hinge Cover

A. Door Stop Screws

A B

B. Door Stop

Standard Door - Freezer Drawer

I "1

A. Cabinet Hinge Hole Plugs

o.._0' _ o oo

"_1'1 ...................................A

A. Hinge Screws

A. Handle Trim

B. Flat-Head Handle Screws C. Refrigerator Door Handle

Front View Side View

A. Shim (on some models) B. Bottom Hinge

C. Hinge Screws

A. Door Stop Screws B. Door Stop

_1 A. Handle Trim

B. Flat-Head Handle Screws C. Refrigerator Door Handle

ii ,i

A B

B A

Door Handle Seal Screw Front

French Doors

A. Hinge Cover Screw B. Top Hinge Cover

C. 5A6"Hex-Head Hinge Screws D. Top Hinge

Bottom Hinges

o-. :::-._,...............................B

{ c

................ A

A. Shim (on some models) B. Bottom Hinge

C. Hinge Screws

Wiring Plug

A. _/32"Set Screw

A. %2" Set Screw

A. Loosen Door Bracket Screws

Depending on your model, your refrigerator may have two front adjustable rollers (Style 1) or four adjustable rollers (Style 2) located at the base of the refrigerator. Ifyour refrigerator seems

unsteady or you want the door to close more easily, use the instructions below.

Stylel-Freezer Door Models

1. Remove the base grille. Grasp the grille firmly and pull it toward you.

2. Remove the bracket cover. Insert the eraser end of a pencil in the cover notch. Apply slight downward pressure to the notched side of the cover while swinging it off.

3. Using a screwdriver or %" hex driver, turn the roller adjustment screw on each side to raise or lower that side of the

refrigerator. NOTE: Having someone push against the top of the

refrigerator takes some weight off the adjustment screws and rollers. This makes it easier to turn the screws It may take

several turns of the roller adjustment screw to adjust the tilt of the refrigerator.

• To raise, turn the roller adjustment screw to the right.

• To lower, turn the roller adjustment screw to the left.

4. Turn the brake foot clockwise until it is firmly against the floor to keep the refigerator from rolling forward when the freezer

drawer is pulled open.

Style 2-Freezer Drawer Models

1. Remove the base grille. Grasp the grille firmly and pull it toward you.

2. Raise or lower the cabinet. Using a %" hex driver, turn the roller adjustment screw(s) on each side to raise or lower that

side of the refrigerator. NOTE: Having someone push against the top of the

refrigerator takes some weight off the adjustment screws and rollers. This makes it easier to turn the screws. It may take

several turns of the roller adjustment screw to adjust the tilt of the refrigerator.

• To raise, turn the roller adjustment screw to the right.

• To lower, turn the roller adjustment screw to the left.

3. Turn the brake foot clockwise until it is firmly against the floor to keep the refigerator from rolling forward when the freezer drawer is pulled open.

A. Rear roller adjustment screw

B. Front roller adjustment screw

C. Brake foot

A. Roller adjustment screw

B. Brake foot

5. Open the door again to make sure that it closes as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both roller adjustment screws to the right. It may take several more turns, and you should turn both adjustment screws the same amount.

6. Replace the bracket cover. Place the bracket cover into the outer edge, swing the cover toward the cabinet and snap it into place.

7. Replace the base grille.

4. Open the door again to make sure that it closes as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws clockwise. It may take several more turns, and you should turn both screws the same

amount.

5. Replace the base grille.

REFRIGERATORUSE

There are two refrigerator compartment doors. The doors can be opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically forms a seal between the two doors.

A. Hinged seal

The temperature controls are located at the top front of the refrigerator or freezer compartments.

IMPORTANT:

• The recommended setting should be correct for normal household refrigerator use. The controls are set correctly

when milk or juice is as cold as you like and when ice cream is firm.

• Wait 24 hours for your refrigerator to cool completely before adding food. Ifyou add food before the refrigerator has cooled

completely, your food may spoil. NOTE: Adjusting the refrigerator and freezer temperature

controls to a colder than recommended setting will not cool the compartments any faster.

• If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.

To Turn Off/On:

Style 1 Press the freezer down arrow touch pad until a dash (-) appears in both the refrigerator and freezer displays.

Neither compartment will cool. Style 2 Turn the freezer control to the word OFR Neither

compartment will cool when the freezer is set to OFR

Energy Saver Option (on some models)

The energy saver option turns off the heater which helps to reduce moisture on the door hinge seal. The refrigerator uses more energy when Energy Saver is off.

• Press the control to ON to save energy when the environment is less humid.

• Press the control to OFF when the environment is warm and more humid, or if you notice moisture on the door hinge seal.

EnetgySaver

Temperature Controls

For your convenience, the temperature controls are preset at the factory. When you first install your refrigerator, make sure the controls are still set to the recommended setting as shown.

Style 1

Recommended Setting "4"

®0® ®0®

corn FREEZER COLDER RecommendedSettings:4 CO_D REFRIGERATOR COLDER

Style 2

Recommended Setting "4"

ColdestSettings:?

Adjusting Controls

If you need to adjust the temperature in either the refrigerator or freezer compartment, use the settings listed in the chart below as

a guide. For (Style 1)controls press the up or down arrow touch pads, or

for (Style 2) controls turn the dial to adjust the temperature. Except when starting the refrigerator, do not adjust either control

more than one setting at a time. Wait 24 hours between adjustments for the temperature to stabilize.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm REFRIGERATORControl

one setting higher

FREEZER too warm/too little ice FREEZER Control one

setting higher

REFRIGERATOR too cold REFRIGERATORControl

one setting lower

FREEZER too cold FREEZER Control one

setting lower

+ 28 hidden pages