Whirlpool G7CE3034X, G7CE3055X, G7CE3635X, G7CE3655X, G9CE3065X DIMENSIONS

...

Electric Built-in Cooktop

PRODUCT MODEL NUMBERS

G7CE3034X, G7CE3055X, G7CE3635X, G7CE3655X, G9CE3065X, G9CE3074X, G9CE3675X, W5CE3024X, W5CE3625A

ELECTRICAL REQUIREMENTS

A 3-wire or 4-wire, single phase, 120/240 volt, 60-Hz., AC only

electrical supply is required on a separate, 40-amp circuit fused on both sides of the line. The model/serial number rating plate is located on the metal cabinet underneath the cooktop. See the following illustration.

NOTE: A separate 30-amp circuit fused on both sides of the line can be used for models W5CE3024 and G9CE3065.

A. Model/serial number plate

PRODUCT DIMENSIONS

A. Glass depth - black and white models - 213/4" (55.2 cm)

Glass depth - stainless steel models - 221/4" (56.4 cm)

B. Glass width - 30" (76.2 cm) models - 30

Glass width - 36" (91.4 cm) models - 365/16" (92.3 cm)

C. Frame depth - 20

/4" (51.5 cm)

D. Frame width - 30" (76.2 cm) models - 28

Frame width - 36" (91.4 cm) models - 347/16" (87.5 cm) E. Cooktop height - 3 F. Cooktop height including conduit (located at rear of

cooktop, right side) - 5

/4" (9.6 cm)

/4" (13.5 cm)

/8" (78.4 cm)

/16" (73.5 cm)

CABINET DIMENSIONS

IMPORTANT: If installing a range hood or microwave hood combination

above the cooktop, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface.

A. 30" (76.2 cm) on 30" models; 36" (91.4 cm) on 36" models B. Combustible area above countertop (shown by dashed box above) C. 30" (76.2 cm) minimum clearance between top of cooktop platform

and bottom of uncovered wood or metal cabinet (24" [61 cm] minimum clearance if bottom of wood or metal cabinet is covered by not less than less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless steel, or

0.024" [0.06 cm] aluminum or 0.020" [0.05 cm] copper) D. 13" (33 cm) recommended upper cabinet depth E. 2" (5.1 cm) on most models; 2

F. 20

/2" (52.0 cm) recommended cutout.

Will ﬁt in cutout from 203/8"-209/16" (51.8-52.2 cm).

G. 18" (45.7 cm) minimum clearance from upper cabinet to countertop

within minimum horizontal clearances to cooktop H. Junction box or outlet: 7" (17.8 cm) minimum from top of countertop I. Junction box or outlet: 9" (23.0 cm) maximum from right side of

cabinet

J. 29

/2" (74.9 cm) recommended cutout on 30" (76.2 cm) models. Will ﬁt in cutout from 291/16"-299/16" (73.8-75.1 cm) on 30" (76.2 cm) models. 351/2" (90.2 cm) recommended cutout on 36" (91.4 cm) models. Will ﬁt in cutout from 349/16"-359/16" (87.8-90.3 cm) on 36" (91.4 cm) models.

K. 1" (2.5 cm) minimum distance to nearest left and right side

combustible surface above cooktop

L. 1" (2.5 cm) minimum clearance between back wall and countertop

NOTES: After making the countertop cutout, some installations may require notching down the base cabinet side walls to clear the cooktop base. To avoid this modiﬁcation, use a base cabinet with sidewalls wider than the cutout.

If cabinet has a drawer, a 5 of the countertop to the top of the drawer (or other obstruction) in base cabinet is required.

/4" [0.6 cm] ﬂame retardant millboard covered with not

/8" (6.7 cm) on model JEC4430B

/2" (14.0 cm) depth clearance from the top

Because Whirlpool Corporation includes a continuous commitment to improve our products, we reserve the right to change materials and speciﬁcations without notice.

Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Speciﬁcations subject to change without notice.

Ref. W10353374

02/20/2017