Whirlpool EV201NXMQ05, EV201NXMQ03, EV120FXMQ06 Owner’s Manual

UPRIGHTFREEZER

For questions about features, operation/perlormance

parts, accessories or service, call: 1-800-253-1361.

In Canada, call for assistance 1-806-461-5681, for installation

www.whirlpool.com or www.whirlpool.com/canada

and service, call: 1-800-807-6777

or visit our website at...

CONGELATEURS

VERTICAUX

1-82143-001/2300214

Au Canada, pour assistance, composez le 1-800-461-5681, pour

installation ou service, le 1-800-807-6777

ou visitez notre site web

www.whirlpool.com/canada

Table of Contents/Table des matieres .................. 2

TABLEOFCONTENTS

TABLEDESMATIERES

FREEZER SAFETY ......................................................................... 3

Proper Disposal of Your Old Freezer or Refrigerator .................. 3

INSTALLATION INSTRUCTIONS .................................................. 4

Unpacking .................................................................................... 4

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 4

Water Supply Connection ............................................................ 5

Door Handle Installation and Removal ........................................ 5

Door Closing ................................................................................. 6

FREEZER USE ................................................................................ 6

Ensuring Proper Air Circulation .................................................... 6

Using the Control ......................................................................... 6

Key Eject Lock ............................................................................. 7

Ice Maker Operation ..................................................................... 7

FREEZER FEATURES .................................................................... 7

Refrigerated Shelves .................................................................... 7

Storage Basket ............................................................................. 7

Storage Gate ................................................................................ 7

FREEZER CARE ............................................................................. 8

Cleaning Your Frost-Free Freezer ................................................ 8

Base Grille .................................................................................... 8

Defrosting and Cleaning Your Manual Defrost Freezer ............... 8

Changing the Light Bulb .............................................................. 9

Power Interruptions ...................................................................... 9

Moving Care ................................................................................. 9

TROUBLESHOOTING .................................................................. 10

ASSISTANCE OR SERVICE ......................................................... 11

In the U.S.A ................................................................................ 11

In Canada ................................................................................... 11

Accessories ................................................................................ 11

WAR RAN TY .................................................................................. 12

SECURITI :!:DU CONGELATEUR .................................................. 13

Mise au rebut appropriee de votre

vieux congelateur ou refrigerateur ............................................. 13

INSTALLATION DU CONGI_LATEUR ......................................... 14

Deballage .................................................................................... 14

Emplacement d'installation ........................................................ 14

Specifications electriques .......................................................... 15

Raccordement de la canalisation d'eau .................................... 15

Installation et depose des poignees de portes .......................... 16

Fermeture de la porte ................................................................. 16

UTIMSATION DU CONGI_LATEUR ............................................. 17

Pour s'assurer d'une circulation d'air appropriee ...................... 17

Utilisation de la commande ........................................................ 17

Serrure h cle separ6e ................................................................. 17

Machine a glagons ..................................................................... 18

CARACTI:!:RISTIQUES DU CONGELATEUR ............................... 18

Clayettes de refrigeration ........................................................... 18

Panier coulissant ........................................................................ 18

Barriere d'entreposage ............................................................... 18

ENTRETIEN DU CONGI:!:LATEUR ............................................... 19

Nettoyage du congelateur sans givre ........................................ 19

Grille de la base .......................................................................... 19

Degivrage et nettoyage du congelateur a degivrage manuel....19

Remplacement de I'ampoule d'eclairage .................................. 20

Pannes de courant electrique .................................................... 20

Demenagement .......................................................................... 21

DI_PANNAGE ................................................................................. 21

ASSISTANCE OU SERVICE ......................................................... 22

Accessoires ................................................................................ 22

GARANTI E..................................................................................... 23

_i, tl_ol °

FREEZERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance, Always read and obey all

safety messages,

This symbol alerts you to potential hazards that can kill or hurt you and others, All safety messages will follow the safety alert symbol and either the word "DANGER" or

This is the safety alert symbol, "WARNING." These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your freezer, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord,

• Disconnect power before servicing.

• Replace all panels before operating.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline, away from freezer,

• Use two or more people to move and install freezer,

• Keep key away from children,

• Remove doors or lid from your old freezer or refrigerator.

• Disconnect power before installing ice maker (on ice maker kit ready models only).

SAVE THESE INSTRUCTIONS

Proper Disposal of

YourOld Freezeror Refrigerator

Suffocation Hazard

Remove doors or (id from your o(d freezer or

refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned freezers or refrigerators are still dangerous ... even if they will sit for "just a few days." If you are getting rid of your old refrigerator or freezer, please follow these instructions to help prevent accidents.

Before you throw away your old freezer or refrigerator:

• Take off the doors or lid.

• Leave the shelves in place so that children may not easily climb inside,

INSTAILATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

freezer.

Failure to do so can result in back or other injury.

NOTE: This freezer may be installed side by side with another

refrigerator or freezer. Allow for a 3 in. (7.5 cm) clearance at the top and sides and a 1/4in. (0.64 cm) clearance between the appliances.

Removing packaging materials

• Remove tape and glue residue from surfaces before turning on the freezer. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your freezer. For more information, see the "Freezer Safety" section.

When Moving Your Freezer: Your freezer is heavy. When moving the freezer for

cleaning or service, be sure to protect the floor. Always pull the freezer straight out when moving it. Do not wiggle or

"walk" the freezer when trying to move it, as floor damage

could occur.

Cleaning before use

After you remove all of the packaging materials, clean the inside

of your freezer before using it. See the cleaning instructions in the "Freezer Care" section.

II I

3" (7.5 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in

death, fire, or electrical shock.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from freezer.

Failure to do so can result in death, explosion,

or fire.

IMPORTANT: Do not install the freezer near an oven, radiator, or

other heat source, nor in a location where the temperature will fall below 40°F (5°C).

Check the strength of the floor before installing your freezer. It should hold the weight of a freezer fully loaded with food.

Allow at least 3 in. (7.5 cm) of air space at the top and on both

sides of the freezer and 1 in. (2.5 cm) between the back of the

freezer and the wall. If the freezer is to be against a wall, leave

extra space on the hinge side so the door can open wider.

Recommended grounding method A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded

electrical supply is required. It is recommended that a separate circuit serving only your freezer be provided. Use an outlet that cannot be turned off by a switch or pull chain. Do not use an

extension cord.

Readalldirectionscarefullybeforeyoubegin.

IMPORTANT:

• If you turn the freezer on before the water line is connected, turn the ice maker OFE

• All installations must meet local plumbing code requirements.

• Use plastic tubing and check for leaks. Install plastic tubing only in areas where temperatures will remain above freezing.

Tools required: Flat-blade screwdriver, 7/16in. and 1/2in. open-end

wrenches or two adjustable wrenches, 1/4in. nut driver and drill bit, hand drill or electric drill (properly grounded).

NOTE: Your freezer dealer has a kit available with a 1/4in. (6.35 mm) saddle-type shutoff valve, a union, and plastic tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3A6in.

(4.76 mm) saddle valve which reduces water flow and clogs more easily.

Cold water supply

Connect the ice maker to a cold water line with water pressure between 30 and 120 psi. If you have questions about your water pressure, call your utility company.

Connecting to Water Line

Unplug freezer or disconnect power.

Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

Locate a 1/2in. to 11/4in. (12.7 mm to 3.18 cm) vertical COLD water pipe near the freezer.

NOTE: Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

Determine the length of plastic tubing you need. Measure from the connection on the lower left rear of freezer to the

water pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use 1/4in. (6.35 mm) O.D. (outside diameter) plastic tubing. Be sure both ends of plastic tubing are cut square.

Using a grounded drill, drill a 1/4in. (6.35 mm) hole in the cold water pipe you have selected.

Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the plastic tubing.

Connecting to Freezer

1. Attach the plastic tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Use the tube clamp on the back of the

freezer to secure the tubing to the freezer as shown. This will help prevent damage to the tubing when the freezer is

pushed back against the wall.

2. Turn shutoff valve ON. Check for leaks. Tighten any connections (including connections at the valve) or nuts that

leak.

1. Tube clamp 3. Compression nut

2. Plastic tubing 4. Valve inlet

3. The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the 1/4in. (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

4. Plug in freezer or reconnect power.

Tools Needed: Flat-blade screwdriver

1.Cold water pipe 5. Compression sleeve

2. Pipe clamp 6. Shutoff valve

3. Plastic tubing 7.Packingnut

4. Compression nut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the 1/4in. (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not overtighten or you may crush the plastic tubing.

7. Slip the compression sleeve and compression nut on the plastic tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

2 _

1. Handle trim

2. Handle screws

3. Door handle

1. Place the handle on the door as shown.

2. Using a flat-blade screwdriver, attach the handle to the door with the 4 handle screws (provided).

3. Place the trim pieces on the upper and lower handle ends as shown.

NOTE: Some models have an (optional) gold trim piece that

snaps on the handle ends before placing the end trim pieces.

4. Applyfirmpressurewithyourhandonthefaceofthetrim. Slidethetoptrimdownandthebottomtrimuptowardthe

handle.

5. Toremovethehandle,reversethesedirections.

1. Locate,removeanddiscardthe4boltsthatheldthefreezer intheshippingcrate.

2. Locatethe2frontlevelinglegstapedamongthepacking materials.

3. Screwtheselegsintothefrontholesonthebottomofthe freezer.Thebackofthefreezerrestson2fixedsupports.

4. Adjustthefrontlegsjustenoughtoliftthecabinetupoffof thefloor.

NOTE:Ifyourmodelisequippedwithrollers,thefrontlegs shouldbeloweredenoughtolifttherollersoffofthefloorto

ensurethefreezerdoesnotrollforwardwhenthedooris opened.

5. Connectfreezertoproperelectricalsupplyandattach retainingclip.(Referto"ElectricalRequirements"section.)

6. Slidefreezerintoplace.

7. Placealevelingtoolontopofthefreezerfirstsidetoside, thenfronttoback.Turnlegcounterclockwisetoraisea corner.Turnlegclockwisetoloweracorner.

Do not block any of these vents with food packages. If the vents are blocked, airflow will be prevented, and temperature and moisture problems may occur.

IMPORTANT: To prevent odors and drying out of food, wrap or cover foods tightly.

Setting the control

Turn the freezer temperature control to 4. This setting is designed to maintain the temperature at or near 0°F (-17.8°C) under normal operating conditions.

Allow the freezer to cool 6 to 8 hours before filling with frozen food. Let the freezer cool overnight before adding large amounts of unfrozen food. Never add more than 2 to 3 Ibs. (907-1,350 g) of unfrozen food per cubic foot (28.32 L) of freezer space.

8. RepeatStep7untilfreezerislevel.

9. Afterfreezerisfullyloadedwithfood,recheckwithlevelasin Step7.

FREEZERUSE

In order to ensure proper temperature, you need to permit proper airflow in the freezer. As shown in the illustration, cool air enters

through the freezer wall and moves down. The air then

recirculates through the vent near the bottom.

NOTE: When the freezer is first started, the compressor will run constantly until the cabinet is cooled. It may take up to 6 or 8 hours (or longer), depending on room temperature and the number of times the freezer door is opened. After the cabinet is cooled, the compressor will turn on and off as needed to keep the freezer at the proper temperature.

The outside of your freezer may feel warm. This is normal. The freezer's design and main function is to remove heat from packages and air space inside the freezer. The heat is transferred to the room air, making the outside of the freezer feel warm.

Adjusting the control

• Turn control to a higher number for colder temperatures.

• Turn control to a lower number for less cold temperatures. NOTE: The small snowflake icon represents the number I or

the least cold setting. The large snowflake icon represents 6 or the coldest setting.

Fast Freeze (on some models)

This setting causes the freezer to run continuously, driving the freezer temperature to the coldest possible temperature. To activate, adjust the control knob to the igloo icon, which

represents the fast freeze setting. Use this feature just before adding large amounts of unfrozen foods. For best food quality, do

not exceed 3 Ibs. (1,350 g) per cubic foot (28.32 L). Return to your normal setting after 24 to 48 hours.

FREEZERFEATURES

Tolockorunlockthefreezer,youmustholdthekeyinthelock

whileturning.Thelockisspringloaded,sothekeycannotbeleft inthelock.

If the key is lost, contact your dealer for a replacement. Always give the model and serial number of your freezer when requesting a replacement key.

To Turn the Ice Maker On/Off

NOTE: Do not force the wire shutoff arm up or down.

• To turn the ice maker on, simply lower the wire shutoff arm. NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes fill the ice storage bin and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position.

• To manually turn the ice maker off, lift the wire shutoff arm to the OFF (arm up) position and listen for the click to make sure

the ice maker will not continue to operate.

This manual covers several different models. The freezer you have purchased may have some or all of the items listed. The locations of the features may not match those of your model.

Your freezer is equipped with refrigerated interior shelves. Packages in direct contact with the shelves will have the best refrigeration. Fresh, unfrozen food packages should be stored directly on the shelves and not on top of already frozen food packages.

When placing the food packages in your freezer, please remember:

• The cabinet shelves have the best freezing capability. The door shelves and the bottom of the cabinet have a slightly less cold temperature. Therefore, packages sensitive to temperature (meat, poultry, etc.) should not be placed on the

door shelves or the freezer bottom.

• Leave some space between the food packages so that cold air can pass over and around them.

The slide out basket provides separate storage space for items that are difficult to store on freezer shelves. To remove the basket, pull out and lift up.

To Increase Ice Production Rate

The ice maker should produce approximately 7 to 9 batches of

ice in a 24-hour period. If ice is not being made fast enough, turn

the Temperature Control toward a higher (colder) number in half

number steps. (For example, if the control is at 3, move it to between 3 and 4.) Wait 24 hours and, if necessary, gradually turn

the Temperature Control to the highest setting, waiting 24 hours

between each increase.

REMEMBER

• Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

• Do not store anything on top of the ice maker or in the ice storage bin.

To lower and raise the storage gate:

1. Lift the top of the gate up slightly, out of the supports. Pull the gate forward and down.

2. Return the gate to the upright position. Lift the top of the gate slightly to clear the supports. Lower the gate into the

supports.

FREEZERCARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Frost-free means that you will never have to defrost your freezer. Frost is removed by air moving and collecting any moisture and depositing it on the cooling coil. The cooling coil periodically warms up just enough to melt the frost, and it then flows down to

the drain pan (located behind the base grille) where it is

evaporated. Complete cleaning should be done at least once a year.

1. Unplug freezer or disconnect power.

2. Remove all frozen food. Wrap frozen food in several layers of newspaper and cover with a blanket. Food will stay frozen for several hours. You may also store frozen food in a cooler, additional refrigerator-freezer, or in a cool area.

3. Wash the inside walls with a solution of mild detergent in warm water or 2 tbs. (26 mg) baking soda to 1 qt. (0.95 L)

warm water. Do not use abrasive or harsh cleaners.

4. Rinse well and wipe dry with a clean soft cloth.

5. Use the appropriate cleaning method for your exterior finish. Painted metal: Wash exteriors with a clean sponge or soft

cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth. For additional protection against damage to painted metal exteriors, apply appliance wax (or auto paste wax) with a clean, soft cloth. Do not wax plastic parts.

Stainless steel finish: Wash with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners. Dry thoroughly with a soft cloth.

To keep your stainless steel refrigerator looking like new and to remove minor scuffs or marks, it is suggested that you use the manufacturer's approved Stainless Steel

Cleaner & Polish.

IMPORTANT: This cleaner is for stainless steel parts only!

• Do not allow the Stainless Steel Cleaner & Polish to come

into contact with any plastic parts such as the trim pieces, dispenser covers or door gaskets. If accidental contact does occur, clean plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft

cloth. To order the cleaner, see the "Accessories" section.

Replace all frozen food.

Plug in freezer or reconnect power.

See the "Using the Control" section.

To remove and replace the base grille:

1. Remove the base grille by opening the freezer door and pulling both sides of the base grille toward you.

2. Replace the base grille by aligning the grille support tabs with the openings in the freezer cabinet. Push firmly to snap grille into place.

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Defrost and clean your freezer when frost has built up to about V4in. (6 mm) thickness. Complete defrosting and cleaning should

be done at least once a year. In high humidity areas, a freezer may need more frequent defrosting and cleaning.

Do not use abrasive cleaners on your freezer. Do not use cleaning waxes, concentrated detergents, bleaches, or cleaners

containing petroleum on plastic parts. Damage can occur. NOTE: The drain cap must be removed before defrosting the

freezer and replaced securely afterward.

1. Unplug freezer or disconnect power.

2. Remove all frozen food. Wrap frozen food in several layers of newspaper and cover with a blanket. Food will stay frozen for

several hours. You may also store frozen food in a cooler, an additional refrigerator-freezer, or a cool area.

3. Remove base grille. (See the "Base Grille" section.)

+ 16 hidden pages