Whirlpool GS5SHAXNT01, GS5SHAXNL00, GS2SHEXNT00, GS2SHAXNT01, GS2SHAXNL00 Owner’s Manual

...

REFRIGERATORUSE&CAREGUIDE

MANUALDEUSOYCUIDADODELREFRIGERADOR

p p

GUIDED'UTILISATIONETD'ENTRETIENDUREFRIGERATEUR

Tableof Contents/Indice/ Tabledesmatibres

ASSISTANCE OR SERVICE ............................ 1

REFRIGERATOR SAFETY ............................... 2

INSTALLATION INSTRUCTIONS ................... 3

REFRIGERATOR USE ..................................... 5

REFRIGERATOR CARE ................................... 7

TROUBLESHOOTING ...................................... 8

WATER FILTER CERTIFICATIONS .............. 10

PRODUCT DATA SHEETS ............................ 11

WARRANTY .................................................... 13

If you need assistance or service, first see the "Troubleshooting" section. Additional help is available by calling our Customer Interaction Center at 1-800-253-1301 from anywhere in the U.S.A., or write:

Whirlpool Corporation

Customer Interaction Center

553 Benson Road

Benton Harbor, MI 49022-2692

In Canada, for installation and service call, 1-800-807-6777. For assistance call 1-800-461-5681 Monday to Friday 8:00 a.m. -

6:00 p.m. (EST), Saturday 8:30 - 4:30 p.m. (EST), or write:

Whirlpool Canada Inc.

Customer Interaction Center

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Information may also be obtained by visiting our website at www.whirlpool.com.

In Canada, visit www.whirlpool.com/canada. Please include a daytime phone number in your correspondence. Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation date for in-warranty service.

AYUDA O SERVIClO TECNICO .................... 14

SEGURIDAD DEL REFRIGERADOR ............ 14

INSTRUCCIONES DE INSTALACI(_N .......... 15

USO DE SU REFRIGERADOR ...................... 18

CUIDADO DE SU REFRIGERADOR ............. 21

SOLUCION DE PROBLEMAS ....................... 22

HOJA DE DATOS DEL PRODUCTO ............ 24

GARANTiA ...................................................... 26

Assistance or Service

Write down the following information about your appliance to help you obtain assistance or service if you ever need it. You will need to know your complete model number and serial number. You can find this information on the model and serial number label, located

on the inside wall of the refrigerator compartment.

Dealer name Serial number

Address Phone number

Model number Purchase date

Toorder replacement filters, call 1-800-442-9991 and ask for the part number listed below or contact your authorized Whirlpool dealer. In Canada, call 1-800-461-5681.

Stainless Steel Cleaner and Polish: Order Part #4396095 Standard Base Filter Cartridges: Order Part #4396508 (NL240/

L400); #4396509 (NL240V and L400V)

ASSISTANCE OU SERVICE .......................... 27

S¢CURITF =DU RCFRIGCRATEUR ................ 27

INSTRUCTIONS D'INSTALLATION .............. 28

UTILISATION DU RleFRIGleRATEUR ........... 31

ENTRETIEN DU RleFRIGleRATEUR ............. 34

DlePANNAGE .................................................. 35

FEUILLES DE DONNleES

SUR LE PRODUIT .......................................... 37

GARANTIE ...................................................... 39

2261717

Wh!_r .....el °

TOD0 LO QUE _AGINA_ _'

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

mPlug into a grounded 3 prong outlet. mDo not remove ground prong.

mDo not use an adapter. mDo not use an extension cord.

mDisconnect power before servicing. mReplace all panels before operating.

mRemove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline, away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

• Use a sturdy glass when dispensing ice or water (on some

models).

ProperDisposal ofYourOldRefrigerator

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of your old refrigerator, please follow these instructions to help

prevent accidents.

Before you throw away your old refrigerator or freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily climb inside.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

NOTE: Do not install the refrigerator near an oven, radiator, or other heat source, nor in a location where the temperature will fall below 55°F (13°C).

V2" (1.25 crn)

Remove packaging materials. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your

refrigerator. For more information, see the "Refrigerator Safety" section.

When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.

Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

important information to know about glass shemves

and covers:

Do not cIean glass shelves or covers with warm water when

they are cold= Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping= For your protection, tempered glass is designed to shatter into many sma!I, pebble-size pieces. This is normal= GIass shelves and covers are heavy= Use special care when removing them to avoid impact from dropping=

ii- i!

2" (5.08 era)

Electricam Shock Hazard

Pmuginto a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can resumt in death, fire, or eiectricam shock.

Explosion Hazard

Keep flammable matedais and vapors, such as gasoJine, away from refrigerator.

Faimureto do so can resumt in death, expmosion, or fire.

To ensure proper ventilation for your refrigerator, allow for 1/2" (1.25 cm) space on each side and at the top. When installing your refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum on

each side (depending on your model) to allow for the door to swing open. If your refrigerator has an ice maker, allow extra space at the back for the water line connections.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15 or 20 amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.

Readalldirectionscarefullybeforeyoubegin. IMPORTANT:

• Ifyouturntherefrigeratoronbeforethewaterlineis connected,turntheicemakerOFE

• Allinstallationsmustmeetlocalplumbingcoderequirements.

• Usecoppertubingandcheckforleaks.Installcoppertubing onlyinareaswherethehouseholdtemperatureswillremain

abovefreezing.

TOOLSNEEDED:Flat-bladescrewdriver,7A6"and1/2"open-end wrenchesortwoadjustablewrenches,1/4"nutdriveranddrillbit, handdrillorelectricdrill(properlygrounded).

NOTE:Yourrefrigeratordealerhasakitavailablewitha1/4" (6.35mm)saddle-typeshutoffvalve,aunion,andcoppertubing. Beforepurchasing,makesureasaddle-typevalvecomplieswith

yourlocalplumbingcodes.Donotuseapiercing-typeor3/16" (4.76mm)saddlevalvewhichreduceswaterflowandclogsmore easily.

WaterPressure

Acoldwatersupplywithwaterpressureofbetween30and 120psi(207-827kPa)isrequiredtooperatethewaterdispenser

andicemaker.Ifyouhavequestionsaboutyourwaterpressure, callalicensed,qualifiedplumber.

ReverseOsmosisWaterSupply IMPORTANT:Thepressureofthewatersupplycomingoutofa

reverseosmosissystemgoingtothewaterinletvalveofthe refrigeratorneedstobebetween30and120psi(207-827kPa)

Ifareverseosmosiswaterfiltrationsystemisconnectedtoyour coldwatersupply,thewaterpressuretothereverseosmosis systemneedstobeaminimumof40to60psi(276-414kPa).

Ifthewaterpressuretothereverseosmosissystemislessthan 40to60psi(276-414kPa):

• Checktoseewhetherthesedimentfilterinthereverse osmosissystemisblocked.Replacethefilterifnecessary.

• Allowthestoragetankonthereverseosmosissystemtorefill afterheavyusage.

• Ifyourrefrigeratorhasawaterfiltercartridge,it mayfurther reducethewaterpressurewhenusedinconjunctionwitha

reverseosmosissystem.Removethewaterfiltercartridge. See"WaterFiltrationSystem."

Ifyouhavequestionsaboutyourwaterpressure,callalicensed, qualifiedplumber.

Determine the length of copper tubing you need. Measure from the connection on the lower rear corner of the refrigerator

to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

Using a grounded drill, drill a 1/4"(6.35 mm) hole in the cold water pipe you have selected.

..................A

G ............................B

........ C

A. Cold water pipe E.Compression sleeve B.Pipe clamp F.Shutoff valve C. Copper tubing G.Packing nut D.Compression nut

6. Fasten shutoff valve to cold water pipe with pipe clamp. Be sure outlet end is solidly in the 1/4"(6.35 mm) drilled hole in the water pipe and that washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws carefully and

evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw the compression nut onto the outlet end with an adjustable wrench. Do not overtighten.

8. Place the free end of the tubing into a container or sink, and turn ON main water supply and flush out the tubing until water

is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.

3. A 1/4"x 1/4"coupling is needed to order to connect the water tubing to an existing household water supply line. Thread the

provided nut onto the coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

{ilk:i_,_i:ii_!x!_<_!ii:i:iiii:ii_,i:!!__i_,i_ii_'iii!:i_i::,_!!_,_i_iii!iii_i:_:!!::_!::_]!i}¸'¸

Read all directions before you begin. IMPORTANT: Ifyou turn the refrigerator on before the water line is

connected, turn the ice maker OFR

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a 1/2"(12.70 mm) to 11/4'' (3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

B c

A.Refrigerator water tubing B.Nut (provided)

C.Bulb

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

6. Plug in refrigerator or reconnect power.

7. Flush the water system see "Water and Ice Dispensers."

NOTE: It may take up to 24 hours for your ice maker to begin producing ice.

D E F

D. Coupling (provided)

E.Ferrule (purchased) F Nut (purchased)

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. Thread the provided nut onto the water valve as shown. NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

Ill

A.Bulb B.Nut (provided)

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

6. Plug in refrigerator or reconnect power.

7. Flush the water system. See "Water and Ice Dispensers."

NOTE: It may take up to 24 hours for your ice maker to begin

producing ice.

REFRIGERATORUSE

For your convenience, your refrigerator controls are preset at the factory. When you first install your refrigerator, make sure that the

controls are still preset. The Refrigerator Control and the Freezer

Control should both be set to the "mid-settings." Style I

IMPORTANT:

• Your product will not cool when the REFRIGERATOR Control is set to OFR

• The Refrigerator Control adjusts the refrigerator compartment temperature. The Freezer Control adjusts the freezer compartment temperature. Settings to the left of the mid-

setting make the temperature less cold. Settings to the right of the mid-setting make the temperature colder.

• Wait 24 hours before you put food into the refrigerator. If you add food before the refrigerator has cooled completely, your

food may spoil.

Style 1

Turn the control to the right (clockwise) to make the compartment colder or to the left (counterclockwise) to make it less cold.

Style 2

1. Push in on the control and release it.

2. The control will pop out. Turn the control to the desired setting.

3. Push the control in to lock it into place.

NOTE: Adjusting the Refrigerator and Freezer Controls to a higher (colder) than recommended setting will not cool the

compartments any faster.

Adjusting Controls

Give the refrigerator time to cool down completely before adding food. It is best to wait 24 hours before you put food into the

refrigerator. The settings indicated inthe previous section should be correct for normal household refrigerator usage. The controls are set correctly when milk or juice is as cold as you like and when

ice cream is firm. If you need to adjust temperatures in the refrigerator or freezer,

use the settings listed in the chart below as a guide. Wait at least 24 hours between adjustments.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm REFRIGERATOR

Control one setting higher

FREEZER too warm/too little ice FREEZER Control

one setting higher

COLD COLDER COLD COLDER

Style 2

REFRIGERATOR too cold REFRIGERATOR

Control one setting lower

FREEZER too cold FREEZER Control

one setting lower

The control can be adjusted to properly chill meats or vegetables. The air inside the pan is cooled to prevent "spot" freezing and can be set to keep meats at the National Livestock and Meat Board recommended storage temperatures of 28° to 32°F (-2° to 0°C).

The convertible vegetable/meat drawer control comes preset at the lowest meat setting.

To store meat: Set the control to one of the three MEAT settings to store meat at

its optimal storage temperature. To store vegetables: Set the control to VEG to store vegetables at their optimal storage

temperatures. NOTE: If food starts to freeze, move the control to the left (less

cold). Remember to wait 24 hours between adjustments.

i#_ii_ _ii_!_ _. i_i

You can control the amount of humidity in the moisture-sealed crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) for best storage of fruits and vegetables with skins. HIGH (closed) for best storage of fresh, leafy vegetables.

ii;iii!ii!!ii i:ii/iiii ¸!li!i ili

: :

Cool air from the freezer is directed to the refrigerator door bin directly beneath the vents.

NOTE: The dairy compartment and can rack are not chilled.

Chilled Door Bin Control

The chilled door bin control is located on the left-hand side of the refrigerator compartment.

Removing and Replacing Ice Storage Bin

1. Hold the base of the storage bin with both hands and press the release button to lift the storage bin up and out.

NOTE: It is not necessary to turn the ice maker control to the OFF (right) position when removing the storage bin. The sensor cover ("flipper door") on the left wall of the freezer

stops the ice maker from producing ice if the door is open or the storage bin is removed.

2. Replace the storage bin on the door and push down to make sure it is securely in place.

A. Door Chill control

Turn the control clockwise (right) to reduce the flow of cold air to the bin and make it less cold.

Turn the control counterclockwise (left) to increase the flow of cold air to the bin and make it colder.

Turning the Ice Maker On/Off

The ON/OFF switch is located on the top right side of the freezer compartment.

Toturn the ice maker on, slide the control to the ON (left) position. To manually turn the ice maker off, slide the control to the OFF

(right) position. NOTE: Your ice maker has an automatic shutoff. The ice maker

sensors will automatically stop ice production, but the control will remain in the ON (left) position.

REMEMBER:

• Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

• The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well

maintained.

• Do not use anything sharp to break up the ice in the bin or bucket. This can cause damage to the ice container and the dispenser mechanism.

• Do not store anything on top of or in the ice maker or storage bin.

Cut Hazard

Use a sturdy glass when dispensing ice or water. Failure to do so can result in cuts.

The Water Dispenser

IMPORTANT:

• The dispensing system will not operate when the freezer door is open.

• After connecting the refrigerator to a water source, flush the water system by dispensing water into a sturdy container until you draw and discard 2 to 3 gal. (8 to 12 L) of water, or for approximately 5 minutes after the water begins dispensing.

The flushing process cleans the water system and clears air from the lines. As the air is cleared from the lines, water may spurt out of the dispenser.

• Allow several hours for the refrigerator to cool down and chill water.

• Dispense enough water every week to maintain a fresh supply.

To Dispense Water:

1. Press a sturdy glass against the water dispenser lever.

2. Remove the glass to stop dispensing.

The Ice Dispenser

The dispensing system will not operate when the freezer door is open. Ice dispenses from the ice maker storage bin in the freezer

when the dispenser lever is pressed. Depending on your model, you may have one or more of the

following options: the ability to select either crushed or cubed ice, a special light that turns on when you use the dispenser, or a lock

option to avoid unintentional dispensing. NOTE: Some models dispense both cubed and crushed ice.

Before dispensing ice, select which type of ice you prefer. For crushed ice, cubes are crushed before being dispensed. This

may cause a slight delay when dispensing crushed ice. Noise from the ice crusher is normal, and pieces of ice may vary in size. When changing from crush to cube, a few ounces of crushed ice

will be dispensed along with the first cubes.

To Dispense Ice:

1. Press the button to select the desired type of ice.

2. Press a sturdy glass against the ice dispenser lever. Hold the glass close to the dispenser opening so ice does not fall

outside of the glass. IMPORTANT: You do not need to apply a lot of pressure to the

lever in order to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing.

The Dispenser Light

Style 1: The dispenser light can be turned on by pressing the ON button.

Style 2: When you use the dispenser, the lever will automatically turn the light on. If you want the light to be on continuously, you

may choose either ON or NIGHT LIGHT. ON: Press the LIGHT button to turn the dispenser light on.

NIGHT LIGHT: Press the LIGHT button a second time to select the Night Light. The dispenser light will automatically adjust to

become brighter as the room brightens, dimmer as the room darkens.

OFF: Press the LIGHT button a third time to turn the dispenser light off.

The dispenser lights are LEDs which should not need to be changed. If it appears that your dispenser lights are not working, check to be sure that the light sensor is not blocked (in Night Light

mode). See "Troubleshooting" for more information.

NOTE: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be

used on disinfected waters that may contain filterable cysts.

Water Filter Status Light (on some models)

The water filter status light will help you know when to change your water filter. The light will change from green to yellow. This tells you that it is almost time to change the filter. It is

recommended that you replace the water filter when the status light changes to red OR water flow to your water dispenser or ice maker decreases noticeably.

After changing the water filter, reset the water filter status light. The status light will change from red to green when the system is

reset.

Non-indicator Water Filter (on some models)

If your refrigerator does not have the status light, you should change the water filter every 6 to 9 months depending upon your

usage. If the water flow to the water dispenser or ice maker decreases noticeably before 6 months have passed, replace the

water filter more often.

Using the Dispenser Without the Water Filter

You can run the dispenser without a water filter. Your water will not be filtered.

1. Remove the water filter.

2. Slide the cap off the end of the filter and replace it in the base grille.

IMPORTANT: Do not discard the cap. It is part of your refrigerator. Keep the cap to use with the replacement filter.

3. Rotate the cap until it is securely in position.

REFRIGERATORCARE

The Dispenser Lock (on some models)

Your dispenser can be turned off for easy cleaning or to prevent unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the product, to the ice maker, or to the dispenser light. It simply deactivates the

dispenser levers. The ice and water dispensers will not work. Style 1: Press the LOCK BuTroN to lock the dispenser. Press the

UNLOCK button to unlock the dispenser. Style 2: Press and hold the LOCK OUT button to lock the

dispenser. Press and hold the LOCK OUT button a second time to unlock the dispenser.

Explosion Hazard

Use nonflammable c_eaner. Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately. IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To prevent

odor transfer and drying out of food, wrap or cover foods tightly.

ToCleanYour Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean sponge or soft cloth and a mild detergent in warm water.

4. There is no need for routine condenser cleaning in normal home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.

TROUBLESHOOTING

If you need to clean the condenser:

• Removethe base grille.

• Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

NOTE: Not all bulbs will fit your refrigerator. Be sure to replace the bulb with one of the same size, shape and wattage. The dispenser

light requires a heavy duty 10-watt bulb. All other lights require a 40-watt bulb. Replacement bulbs are available from your dealer.

1. Unplug refrigerator or disconnect power.

2. Remove light shield when applicable. NOTE: To clean the light shield, wash it with warm water and

liquid detergent. Rinse and dry the shield well.

3. Remove light bulb and replace with one of the same size, shape and wattage.

4. Replace light shield when applicable.

5. Plug in refrigerator or reconnect power.

Trythe solutions suggested here first inorder to avoid the cost of an unnecessary service call.

The refrigerator isn't cooling

• Are the temperature controls set at the mid-settings? The controls are preset at the factory to the correct mid-setting. After connecting power, wait 1 hour before checking temperature.

NOTE: Adjusting the controls to coldest setting will not cool either compartment more quickly.

The lights do not work

• Is the power supply cord unplugged? Plug into a grounded 3 prong outlet.

• Is a light bulb loose in the socket or burned out? See "Changing the Light Bulbs."

• Is the dispenser light set to ON? The dispenser light will operate only when the levers are pressed. If you want the

dispenser light to stay on continuously, set the dispenser light to ON, or NIGHT LIGHT. See "Water and Ice Dispensers."

• Is the dispenser light set to NIGHT LIGHT? If the dispenser is set to the NIGHT LIGHT mode, be sure the dispenser light

sensor is not blocked. See "Water and Ice Dispensers."

Temperature is too warm

Check the following:

• Are the air vents blocked in either compartment?

• Are the door(s) opened often?

• Has a large amount of food just been added to the refrigerator or freezer?

• Are the controls set correctly for the surrounding conditions?

The motor seems to run too much

Check the following:

• Is the room temperature hotter than normal?

• Has a large amount of food just been added to the refrigerator?

• Are the doors opened often?

• Are the doors not closed completely?

• Are the condenser coils dirty?

NOTE: Your new refrigerator will run longer than your old one due to its high-efficiency motor.

There is interior moisture buildup

Check the following:

• Are the air vents blocked in the refrigerator?

• Are the door(s) opened often?

• Isthe room humid?

• Are the controls set correctly for the surrounding conditions?

• Was a self-defrost cycle completed?

The doors will not close completely

Check the following:

• Are food packages blocking the door open?

• Is the ice storage bin out of position?

• Were the doors removed during product installation and not properly replaced?

The doors are difficult to open

The ice dispenser will not operate properly

• Are the gaskets dirty or sticky? Clean gaskets with mild soap and warm water.

The ice maker is not producing ice ornot enough ice

Check the following:

• Is the ice maker wire shutoff arm or switch (depending on models) in the OFF position?

• Is the water line shutoff valve to the refrigerator turned on?

• Is the freezer temperature cold enough to produce ice? Wait 24 hours after ice maker hookup for ice production.

• Has the ice maker just been installed? Wait 72 hours for full ice production to begin.

• Does the ice maker mold have water in itor has no ice been produced? Make sure your refrigerator has been connected to a water supply and the supply shutoff valve is

turned on. Has a large amount of ice just been removed? Allow

24 hours for ice maker to produce more ice. Is there a water filter installed on the refrigerator? The filter

may be clogged or installed incorrectly. Is an ice cube jammed in the ice maker ejector arm?

For models with an interior ice bin, remove the ice from the ejector arm with a plastic utensil. For models with an ice

storage bin located on the freezer door, access the ice maker by depressing the ice sensor door on the upper left side of the freezer interior. While depressing the sensor door, lift the ice maker service door and remove the ice from the ejector with a

plastic utensil.

Off-taste, odor or gray color in the ice

Check the following:

• Are the plumbing connections new, causing discolored or off- flavored ice?

• Have the ice cubes been stored too long?

• Does the freezer and ice bin or bucket need to be cleaned?

• Has food in the freezer or refrigerator been wrapped properly?

• Does the water contain minerals (such as sulfur)? A filter may need to be installed to remove the minerals.

• Is there a water filter installed on the refrigerator? Gray or dark discoloration in ice indicates that the water filtration

system needs additional flushing.

Check the following:

• Is the freezer door closed completely?

• Is the ice storage bin installed correctly?

• Is there ice in the storage bin?

• Has the ice frozen in the storage bin?

• Is ice stuck in the delivery chute?

• Has the wrong ice been added to the storage bin? Use only cubes produced by the current ice maker.

• Has the ice melted around the auger (metal spiral} in the ice bucket? Dump the ice cubes and clean the ice storage

bin.

• Is the ice dispenser stalling while dispensing "crushed" ice? Change the ice button from "crushed" to "cubed." If

cubed ice dispenses correctly, depress the button for "crushed" ice and begin dispensing again.

• Has the dispenser arm been held in too long? Ice will stop dispensing when the arm is held in too long. Wait 3 minutes

for dispenser motor to reset before using again.

The water dispenser will not operate properly

Check the following:

• Is the water shutoff valve not turned on, incorrectly installed or clogged?

• Is the water line connected at the source?

• Is there a kink in the home water source line?

• Has the water system not filled? The water system needs to be filled the first time it is used.

• Is the refrigerator connected to a cold water line with water pressure of at least 30 psi? The water pressure to the home determines the flow from the dispenser.

• Is there a water filter installed on the refrigerator? The filter may be clogged or incorrectly installed.

Water or ice is leaking from the dispenser

Check the following:

• Is the glass not being held under the dispenser long enough?

• Is an ice cube stuck in the chute and holding the trap door open?

The dispenser water is not cool enough

NOTE: Water from the dispenser is chilled to only 50°F (10°C).

• Has the refrigerator been newly installed or a large amount of water recently dispensed? Allow 24 hours for the refrigerator to cool completely.

• Has water not been recently dispensed? The first glass of water may not be cool. Discard the first glass of water.

WATERFILTERCERTIFICATIONS

State ot CaIifl)_nia

Depamnem of Heaifl_ Services

Water Treatment Device

Certificate Number

03- 1550

DaW lss_ed: Jauuary 21.2(X)_

Trademark/Model Desivnatioa Replacement Elemems Rated ('_

Whlll r WI--NL24_ Nt_40 24O ga

........ • l WF-IAf)0 400 400 gaI

Manufacturer: W_I,_II_O01Ct,w

I lie water treatment det'ice(_) lisIed Oil Ibis e_tnfl_at¢ |ltye L_letUle te_ting r_qtt_relllenls p_saallt to _ecIion

116830 of the Heahh and Sal¢ly f'ode |_r the fotlowin_ heallh related eolliaminants:

_licrobiologicaI Cuntaminants and Turbiditv Inor ga_i_iRad Jologica t Contamlnan_s

N_me _one

Organic Colllaminallts

Rated Service Flow: 05 gpm

Do not use with ssater that is microbiologically 9nsafe or oI unknown q9ality_ without adequate disinfection before or a_er the system.

Stare of Caliibrnia

Deparmmnt of Health Services

Water Treatment Device

Certificate Number

03 - 1549

t)atc Issue'd: Ja_luary 21. ?003

Ret_lacenlent Elements Rated t"a_

,i ,L

no not use with water that is microbiologically unsafe or oI unknown quality, without adequate disinfection helore or after the s_stem.

240 gal

400 gal

PRODUCTDATASHEETS

Base Grille Water Filtration System

Model WF-NL240/NL240 Capacity 240 Gallons (908 Liters)

Model WF-L400/L400 Capacity 400 Gallons (1514 Liters)

42 for the reductionof Chlorine,Tasteand Odor, ParticulateClass ll*; Testedand certifiedby NSF international against ANS!/NSF Standard

andagainst ANSt/NSF Standard53 for the reductionof Lead.

This system has been tested according to ANSl/NSF 42/53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in ANSI/NSF 42/53.

Substance Reduction NSF Reduction Average InfluentChallenge Maximum Average Minimum % Average % NSF Test Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction Number

Chlorine Taste/Odor _50% 2.0 mg/L 2.0 mg/L ± 10% 0.03 mg/L 0.025 mg/L 98.5% 99.0% 504232-01

Particulate Class I1" _85% 833,333/mL Atparticles/mLleast10,000 100,000/mL** 40,667/mL 88.0% 95.1% 507163-02

Contaminant NSF Reduction Average InfluentChallenge Maximum Average Minimum % Average % NSF Test

Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction Number

Lead: @pH 6.5 0.01mg/L 0.16 mg/L*** 0.15 mg/L ± 10% 0.001 mg/L 0.001 mg/L 99.35% 99.35% 507610-01 Lead: @pH 8.5 0.01mg/L 0.15 mg/L*** 0.15 mg/L ± 10% 0.001 mg/L 0.001 mg/L 99.31% 99.31% 507611-01

Test Parameters: pH = 7.5 + 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 63°F

(17.2°C).

• It is essential that operational, maintenance, and filter replacement requirements be carried out for the product to

perform as advertised.

• Model WF-NL240 Change cartridge at least every 6 - 9 months. Use replacement cartridge NL240, part

#4396508. 2004 suggested retail price of $32.99 U.S.A./ $49,95 Canada. Prices are subject to change without notice.

• Model WF-L400 The filter monitor system measures the amount of water that passes through the filter and alerts you

to replace the filter. When 90% of the filter's rated life is used, the filter indicator light changes from green to yellow. When

100% of the filter's rated life is used, the filter indicator light changes from yellow to red, and it is recommended that you

replace the filter. Use replacement cartridge L400, part #4396508. 2004 suggested retail price of $32.99 U.S.A./

$49.95 Canada. Prices are subject to change without notice.

• The product is for cold water use only.

• Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

• Refer to the front cover or "Assistance or Service" section for the Manufacturer's name, address and telephone number.

• Refer to the "Warranty" section for the Manufacturer's limited warranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well Water Pressure 30 - 120 psi (207 - 827 kPa) Water Temperature 33 ° - 100°F (0.6° -37.8 ° C) Service Flow Rate 0.5 gpm (1.9 L/min.) @ 60 psi.

* Class II paCdcle size: >1 to <5

** Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

*** These contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.

® NSF is a registered trademark of NSF International.

Base Grille Water Filtration System

Tested and certified by NBF International against ANSI/NSF Standard 42 for the reduction of Chlorine, Taste and Odor, Particulate Class {1";

and against ANB{/NSF Standard 53 for the reduction of Lead, Mercury, Benzene, Toxaphene, p-dichlorobenzene, and Carbofuran=

water leaving the system, as specified in ANSI/NSF 42/53,

Model WF-NL240V/NL240V Capacity 240 Gallons (908 Liters)

Chlorine Taste/Odor _50% 2.0 mg/L 2.0 mg/L _+10% 0.03 mg/L 0.02 mg/L 98.5% 99.0% 504232-01

Particulate Class II* _85% 833,333/mL Atparticles/mlleast10,000 100,000/mL** 40,667/mL 88.0% 95.1% 507163-02

Contaminant NSF Reduction Average InfluentChallenge Maximum Average Minimum % Average % NSF Test

Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction Number

Lead: @pH 6.5 0.01mg/L 0.16 mg/L*** 0.15 mg/L_+ 10% 0.001 mg/L 0.001 mg/L 99.35% 99.35% 507610-01 Lead: @pH 8.5 0.01mg/L 0.15 mg/L*** 0.15 mg/L _+10% 0.001 mg/L 0.001 mg/L 99.31% 99.31% 507611-01

Mercury: @ pH 6.5 0.003 mg/L 0.0062 mg/L 0.006 mg/L _+10% 0.0003 mg/L 0.00023 mg/L 95.2% 96.8% 507160-02 Mercury: @ pH 8.5 0.002 mg/L 0.0061 mg/L 0.006 mg/L _+10% 0.0009 mg/L 0.00052 mg/L 85.2% 91.8% 507161-02

Benzene 0.005 mg/L 0.014 mg/L 0.015 _+10% 0.0005 mg/L 0.0005 mg/L 96.4% 96.4% 507169-02

p-dichlorobenzene 0.075 mg/L 0.219 mg/L 0.225 _+10% 0.0005 mg/L 0.0005 mg/L 99.77% 99.77% 507172-02 Toxaphene 0.003 mg/L 0.014 mg/L 0.015 _+10% 0.0012 mg/L 0.001 mg/L 91.43% 92.6% 507171-02 Carbofuran 0.04 mg/L 0.077 mg/L 0.080 _+10% 0.031 mg/L 0.0064 mg/L 59.7 % 91.6% 507168-02

Model WF-L400V/L400V Capacity 400 Gallons (1514 Liters)

Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum % Average % NSF Test Aesthetic Effects Requirement Influent Concentration Effluent Effluent Reduction Reduction Number

Chlorine Taste/Odor _50% 2.0 mg/L 2.0 mg/L _+10% 0.03 mg/L 0.02 mg/L 98.5% 99.0% 504232-01

Particulate Class II* _85% 833,333/mL Atparticles/mlleast10,000 100,000/mL** 40,667/mL 90.9% 95.1% 507163-02

Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum % Average % NSF Test

Reduction Requirement Influent Concentration Effluent Effluent Reduction Reduction Number

Lead: @ pH 6.5 0.01mg/L 0.16 mg/L*** 0.15 mg/L _+10% 0.001 mg/L 0.001 mg/L 99.35% 99.35% 507610-01

Lead: @ pH 8.5 0.01mg/L 0.15 mg/L*** 0.15 mg/L _+10% 0.001 mg/L 0.001 mg/L 99.31% 99.31% 507611-01

Mercury: @ pH 6.5 0.003 mg/L 0.0062 mg/L 0.006 mg/L _+10% 0.0003 mg/L 0.00023 mg/L 95.2% 96.22% 507160-02

Mercury: @ pH 8.5 0.002 mg/L 0.0061 mg/L 0.006 mg/L _+10% 0.0009 mg/L 0.00052 mg/L 85.2% 91.57% 507161-02

Benzene 0.005 mg/L 0.014 0.015 _+10% 0.005 mg/L 0.0005 96.4% 96.4% 507169-02

p-dichlorobenzene 0.075 mg/L 0.219 0.225_+ 10% 0.0005 mg/L 0.0005 99.77% 99.77% 507172-02 Toxaphene 0.003 mg/L 0.014 0.015_+ 10% 0.0012 mg/L 0.001 91.43% 92.86% 507171-02 Carbofuran 0.04 mg/L 0.0768 0.080 _+10% 0.031 mg/L 0.0057 59.7 % 92.5% 507168-02

• It is essential that operational, maintenance, and filter • Do not use with water that is microbiologically unsafe or replacement requirements be carried out for the product to of unknown quality without adequate disinfection before

perform as advertised, or after the system. Model WF-NL240V Change cartridge at least every 6-9 • Refer to the front cover or "Assistance or Service" section for

months. Use replacement cartridge NL240V, part #4396509. the Manufacturer's name, address and telephone number. 2004 suggested retail price of $35.99 U.S.A./S59.95 Canada. • Refer to the "Warranty" section for the Manufacturer's limited

Prices are subject to change without notice, warranty. Model WF-L400V The filter monitor system measures the

amount of water that passes through the filter and alerts you Application Guidelines/Water Supply Parameters to replace the filter. When 90% of the filter's rated life is used, Water Supply City or Well

the filter indicator light changes from green to yellow. When Water Pressure 30 - 120 psi (207 - 827 kPa) 100% of the filter's rated life is used, the filter indicator light Water Temperature 33 ° - 100°F (0.6 ° - 37.8 ° C)

changes from yellow to red, and it is recommended that you Service Flow Rate 0.5 gpm (1.9 L/rain.) @ 60 psi. replace the filter. Use replacement cartridge L400V, part

#4396509. 2004 suggested retail price of $35.99 U.S.A./ $59.95 Canada. Prices are subject to change without notice.

The product is for cold water use only.

*Class II particle size: >1 to <5

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

***These contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.

(¢ NSF is a registered trademark of NSF International.

+ 28 hidden pages