Whirlpool ED25DQXDB00 User Manual

USE AND CARE GUIDE
GUIDE D’UTILISATION ET D’ENTRETIEN
MANUAL DE US0 Y MANEJO
2180534 Rev. A
NO-FROST SIDE-BY-SIDE REFRIGERATOR
WITH THIRSTCRUSHER* DISPENSING SYSTEM
RkFRlGeRATEUR-CONGkATEUR
SANS GIVRE DE 623 A 764 DM3 (22 PI A 27 P13)
REFRIGERADORES QUE NO HACEN
A Note to You.. Refrigerator Safety Parts and Features Before Using Your Refrigerator Using Your Refrigerator..
Setting the controls Changing the control settings.. Removing the snap-on door trivet Removing the drop-in door trim..
Adjusting the door bins .........................................
Removing the tall-bottle retainer Adjusting the cantilever refrigerator shelves Adjusting the EZ-TRACK’ refrigerator shelf..
Removing the meat drawer and cover
Adjusting the meat drawer temperature
Removing the crisper and crisper cover..
Adjusting the crisper humidity control
..........................................................
...................................................
...................................................
.............................
.........................................
...............................................
..............................
.........................
...........................
...........................
................
..............
............ 12
.................
Page
........ .9
......
10
11 11
12
1 2 3 8 7
7 7 8 8 8 9
Removing the snack bin.. ....................................
Removing the freezer baskets ............................
Removing the freezer shelf .................................
Using the THIRSTCRUSHER*
dispensing system ..............................................
Using the automatic ice maker.. ..........................
Removing the ice maker storage bin..
Attaching the ice maker to a water supply
Removing the base grille.. ...................................
Changing the light bulbs .....................................
Understanding the sounds you may hear
Saving energy .....................................................
Caring for Your Refrigerator.. ................................
Food Storage Guide ...............................................
Troubleshooting .....................................................
Requesting Assistance or Service..
Warranty.. ................................................................
...................... 27
Page
12 13 13
14 16
................. 17
.......... 18
20 20
.......... .22
22
23 25 26
29
A
Note to You
Thank you for buying a WHIRLPOOL* appliance.
Because your life is getting busier and more complicated, WHIRLPOOL Refrigerators are easy to use, save time, and help you manage your home better. To ensure you enjoy years of trouble-free operation, we developed this Use and Care Guide. It contains valuable information about how to operate and maintain your appliance properly and safely. Please read it carefully. Also, please complete and mail the Ownership Registration Card provided
with your appliance. This card helps us notify you about any new information on your appliance.
Please record your model’s information.
Whenever you call to request service on your appli-
ante, you need to know your complete model number and serial number. You can find this information on the model and serial number label (see diagrams on pages 3-5 for location of label).
Please also record the purchase date of your appli­ance and your dealer’s name, address, and telephone number.
Keep this book and the sales slip together in a safe place for future reference.
Model Number Serial Number Purchase Date Dealer Name Dealer Phone
Our Consumer Assistance Center number is toll­free from anywhere in the U.S.A. 24 hours a day.
I
1-800-253-1301
I

Refrigerator Safety

Your safety is important to us.
This guide contains statements under warning sym­bols. Please pay special attention to these symbols and follow any instructions given. Here is a brief explanation of the use of the warning symbol.
IMPORTANT SAFETY INSTRUCTIONS
This symbol alerts you to such dangers as fire, electrical shock, burns, and personal injury.
l
Read all instructions before using the refrigerator.
@Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous . . .
even if they will “just sit in the
@Never allow children to operate, play with, or
crawl inside the refrigerator.
@Never clean refrigerator parts with flammable
fluids. The fumes can create a fire hazard or
garage a few days.” explosion.
If you are getting rid of your old refrigerator, do it safely. Please read the enclosed safety booklet from the Association of Home Appliance Manufac-
turers. Help prevent accidents.
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. THE FUMES CAN CREATE A FIRE HAZARD OR EXPLOSION.
- SAVE THESE INSTRUCTIONS -
Help us help you
Please:
l
Install and level the refrigerator on a floor that will hold the weight and in an area suitable for its size and use.
l
Do not install the refrigerator near an oven, radiator, or other heat source.
l
Do not use the refrigerator in an area where the room temperature will fall below 55°F (13°C).
l
Keep the refrigerator out of the weather.
l
Connect the refrigerator only to the proper kind of outlet, with the correct electrical supply and ground­ing. (Refer to the Electrical Requirements and Grounding Instructions Sheet.)
l
Do not load the refrigerator with food before it has time to get properly cold.
l
Use the refrigerator only for the uses described in this manual.
l
Properly maintain the refrigerator.
l
Be sure the refrigerator is not used by anyone unable to operate it properly.
l
FOR YOUR SAFETY
l
2

Parts and Features

This section contains captioned illustrations of your appliance. Use them to become familiar with where all parts
and features are located and what they look like. Page references are included for your convenience.
NOTE:
The model you have purchased may have all or some of the parts and features shown and they may not
match the illustration exactly. This manual covers several models.
Quick freeze
Light (behi”+ quick freeze
compartment)
(P. 21)
Automatic Ice
maker with cubed
(P. 1)
Utlllty
- compartment
Adjustable
- glass shelves (P. 9)
EZ-TRACK’
L
L Wine rack
glass shelf
(P. 10)
Removable freezer shelves+
(P. 12)
Slide-out freezer baskets+
Levellng rollers H (behind base grille)
(P. 6)
tnumber varies wlth model
Base grille (P. 20)
Meat drawer temperature control (on side wall)
(P. 11)
DESlGNE@YlE
\
Meat drawer (P. 11)
\
adjustable
\
Crlsper light
controlled crisper
Tall-bottle
retalner
(P. 9)
Beep
door bin
(P. 8)
(P. 20)
Humidity-
(P. 12)
3
Automatic ice maker with cubed
p$-ln door trim 4
ice bin (P. 17)
Removable
freezer shelves+
Slide-out
Control panel (P. 7) -
-\
Model and serial
number label
(on side wall)
(P. 1)
Utility
compartment
EZ-TRACK’
glass shelf
(P. 10)
II
II
Load lock+
(P. 9)
Snap-on trivet ­(P. 8)
Leveilng rollers
(behind base grille) (P. 6)
tnumber varies with model
-yP &at drawer \ temperature
Base grille control (P. 20)
(on side wall) (P. 11)
Meat drawer (P. 11)
\
controlled crisper
20)
(P.
Humidity-
(P. 12)
Automatic ice maker with cubed and crushed ice 1
(P. 16) Dropin door trim,
(P. 8) ice bin -
(P. 17) Light !
(P. 21) Removable
freezer shelves+ (P. 13)
Snack bln A (P. 12)
Snap-on door trivets
(P. 8) \
Control panel , Light (P. 7) \
dei and serial
number label
(on side wall)
Slide-out
freezer baskets+ H
(P. 13)
Leveling rollers ­(behind base grille)
(P. 6)
tnumber varies with model
Control panel
(P. 20)
(on side wall) (P. 11)
(P. 11)
Freezer control
Refrigelrator control

Before Using Your Refrigerator

It is important to prepare your refrigerator for use. This section tells you how to clean it, connect it to a power source, install it, and level it.
Cleaning your refrigerator
Removing packaging materials
Remove tape and any inside labels (except the model and serial number label) before using the refrigerator.
To remove any remaining tape or label glue:
l
Rub briskly with thumb.
OR
l
Apply liquid hand-dishwashing detergent to area before removing glue as described above. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners. These can damage the material. See “Important Safety Instructions” on page 2.
Plugging it in
Recommended Grounding Method
A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused and properly grounded electrical supply is required. It is recommended that a separate circuit serving only this appliance be provided. Use a receptacle which cannot be turned off with a switch or pull chain. Do not use an extension cord. See Electrical Requirements and Grounding Instructions Sheet in your Literature
Package.
NOTE:
labels inside your refrigerator. Do not remove the Tech Sheet fastened under the refrigerator at the front.
Cleaning it before use
After removing all packaging materials, clean your
Refrigeratc­power con
Do not remove any permanent instruction
refrigerator before using it, if necessary. See cleaning instructions on page 23.
Sprang grounding type wail receptacle J&
Iii
3-prong groundlng plug
Installing it properly
1.
Allow l/2 inch (1.25 cm) space on each side and at the top of the refrigerator for ease of installation.
2. If the hinge side of the refrigerator is to be against a wall, you might want to leave extra space so the door can be opened wider.
3. The refrigerator can be flush against the back wall.
Leveling it
Your refrigerator has two front leveling screws - one on the right and one on the left. To adjust one or both of these, follow the directions below.
1.
Remove base grille. (See page 20.)
2. To raise front, turn screw clockwise.
3. To lower front, turn screw counterclockwise.
4. Check with level.
5. Replace base grille. (See page 20.)
Right to raise;
left to lower
Use a screw-
driver to adjust
6

Using Your Refrigerator

To obtain the best possible results from your refrigerator, it is important that you operate it properly. This section tells you how to set the controls, remove and adjust the features in your refrigerator, and how to save energy.

Setting the controls

Controls for the refrigerator and freezer are in the refrigerator. When you plug in the refrigerator for the first time:
1. Set the Refrigerator Control to 3 (Recommended Setting).
1 (warmest) to 5 (coldest).
2. Set the Freezer Control to B (Recommended Setting).
A (warmest) to C (coldest).
Give the refrigerator time to cool down completely before adding food. This may take several hours. The settings indicated above should be correct for normal household refrigerator usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm. If you need to adjust these settings, see “Changing the control settings” below.
Refrigerator Control settings range from
Freezer Control settings range from
NOTE:
The Automatic Exterior Moisture control continuously guards against moisture buildup on the outside of your refrigerator cabinet. This control does
not have to be set or adjusted.

Changing the control settings

If you need to adjust temperatures in the refrigerator or
freezer, use the settings listed in the chart below as
a guide. If you have any questions, call our Consumer Assistance Center number, 1-800-253-l 301, from anywhere in the U.S.A.
CONDITION: REASON:
Refrigerator section too warm
Freezer section
too warm
Refrigerator section too cold
l
Door opened often
l
Large amount of food added
l
Room temperature too warm
l
Door opened often
l
Large amount of food added
l
Very cold room temperature (can’t cycle often enough)
l
Controls not set correctly for your conditions
l
Adjust the Refrigerator Control first.
l
Wait at least 24 hours between adjustments.
l
Then adjust the Freezer Control if needed.
RECOMMENDED SETTINGS:
Refrigerator
4
3
2
Freezer
A
C
B
Ice not made
fast enough
Both sections
too warm
l
Heavy ice usage
. Very cold room temperature
(can’t cycle often enough)
l
Door opened often
l
Large amount of food added
l
Very warm or very cold room temperatures
3
4
C
B

Removing the snap-on door trivet

(on some models)
To remove the trivet:
1.
Remove all items from the shelf.
2. Pull out on the inside tab at each end.
3. Lift trivet straight out.
To replace the trivet:
1.
Line up ends of the trivet front with the button on the
door liner wall.
2. Push trivet front straight back until it snaps securely
into place.
3. Replace items on the shelf.
Removing the drop-in door trim (dispenser area)
Remove the trim above the dispenser area for easier
cleaning.
To remove the trim piece:
1.
Remove all items from the shelf.
2. Pull straight up at each end of the trim piece.
To replace the trim piece:
1.
Line up each end of the trim piece above the trim pocket opening in the door liner wall.
2. Push the trim piece straight down until it stops.
3. Replace items on the shelf.

Adjusting the door bins

To remove door bins:
1.
Lift bin up.
2. Pull bin straight out.
To replace door bins:
1.
Slide bin in above desired support button.
2. Push down until it stops.
011
Support
button

Removing the tall-bottle retainer

The tall-bottle retainer fits onto any door bin in your refrigerator. The retainer helps to hold tall bottles in place when opening and closing the refrigerator door.
To remove tall-bottle retainer:
1.
Grasp sides of retainer.
2. Push back gently until the retainer releases from the bin.
To replace tall-bottle retainer:
1.
Position retainer above desired door bin.
2. Gently press back rear tabs and push retainer down onto bin until it locks onto bin.
3. Push retainer forward until it locks into place.

Adjusting the cantilever refrigerator shelves

Adjust the shelves to match the way you use your
refrigerator. Glass shelves are strong enough to hold
bottles, milk, and other heavy food items.
To remove a shelf:
1.
Remove items from shelf.
2. Tilt shelf up at front.
3. Lift shelf at back.
4. Pull shelf straight out.
To replace a shelf:
1.
Guide the rear shelf hooks into the slots in the shelf supports on the back liner wall.
2. Tilt front of shelf up until hooks drop into slots.
3. Lower front of shelf to a level position.
To slide shelf out (on some models):
l
Carefully pull front of shelf toward you.
To slide shelf in:
l
Push shelf in until it stops.
NOTE:
Glass shelves are heavy. Handle them
carefully.
9
Adjusting the E&TRACK* refrigerator shelf
The EZ-TRACK shelf slides from side to side for more flexible storage in your refrigerator.
To slide shelf side to side:
1.
Lift slightly on shelf front.
2. Slide to desired location.
3. Lower shelf front to level position.
NOTE:
You do not have to remove small items from
the shelf before moving it side to side. You may need
to remove larger items.
To remove the shelf:
1.
Remove all items from the shelf.
2. Hold back of shelf with one hand.
3. Lift front of shelf to 45” angle.
4. Lower shelf slightly to release shelf from upper channel of track. Then pull shelf straight out.
NOTE:
Shelf is heavy. Make sure you use both
hands when removing shelf.
To remove shelf track:
1.
Lift both sides of track slightly.
2. Pull track straight out.
Lift front slightly then slide to new location.
Hold wlth both hands and Ilft front to 45” angle.
Hold both sides and Ilft up and out.
II
I I’
To replace shelf track:
1.
Guide track hooks into the shelf support slots on the back wall of the cabinet.
NOTE:
Make sure both sets of track hooks are in
slots and that the slots are parallel to each other.
2. Push track backward and down.
3. Check that track is completely seated in the shelf supports.
10
Shelf support
Make sure both sets of hooks are In support slots.
To reinstall shelf:
1.
Hold shelf at front and back.
2. Tilt front of shelf up to a 45” angle to track.
3. Insert both rear shelf slides into upper channel of track.
4. Lower front of shelf to a level position.
ml
Upper channel
NOTE:
in the track before letting go of shelf.
Make sure both rear shelf slides are securely
Insert rear shelf
slides Into
upper channel
oi back.

Removing the meat drawer and cover

To remove the meat drawer:
1.
Slide meat drawer straight out to the stop.
2. Lift the front slightly.
3. Slide out the rest of the way.
4. Replace in reverse order.
To remove the cover:
1.
Remove meat drawer and crisper.
2. Lift front of cover off supports.
3. Lift cover out by pulling up and out.
To replace the cover:
1.
Fit back of cover into notch supports on walls
of refrigerator.
2. Lower front into place.
3. Replace meat drawer and crisper.
Pull out to the stop, Ilft the front,
and pull agaln.

Adjusting the meat drawer temperature

Cold air from the freezer flows into the meat drawer. This helps keep the meat drawer colder than the rest of the refrigerator for better storage of meats.
Slide the control from side to side to let more or less
cold air through.
Use the control to
K meat drawer.
I
adjust the temperature
11

Removing the crisper and crisper cover

To remove the crisper:
1.
Slide crisper straight out to the stop.
2. Lift the front and slide out the rest of the way.
3. Replace in reverse order.
To remove the cover:
1.
Hold cover firmly with both hands and lift front of cover off supports.
2. Lift cover out by pulling up and out.
To replace the cover:
1.
Fit back of cover into notch supports on walls of refrigerator.
2. Lower front into place.
Remove the glass Insert.
Lift the cover front, then the back. NOTE: Handle glass insert with care. It is
heavy.

Adjusting the crisper humidity control

Pull
out to the stop, Ilft
the front, and pull again.
(on some models)
You can control the amount of humidity in the mois­ture-sealed crisper. Adjust the control to any setting between LOW and HIGH.
l
LOW (open) lets moist air out of the crisper for best
storage of fruits and vegetables with skins.
l
HIGH (closed) keeps moist air in the crisper for best
storage of fresh, leafy vegetables.

Removing the snack bin

To remove the snack bin:
1.
Slide snack bin straight out to the stop with an even,
constant motion.
2. Lift the front.
3. Slide bin out the rest of the way.
4. Replace in reverse order.
Humidity Control
nwl~~.~.LOW
-
2
Pull out to the
il
stop, Ilft the front, and pull again.
12

Removing the freezer baskets

To remove a basket:
1.
Slide basket out to the stop.
2. Lift the front to clear the stop.
3. Slide basket out the rest of the way.
To replace a basket:
1.
Place basket on the slides.
2. Make sure the wire stops clear the front of the slides.
3. Slide basket in all the way.

Removing the freezer shelf

To remove the shelf:
1.
Lift right side of shelf off supports.
2. Slide shelf out of shelf support holes.
3. Replace in reverse order.
Pull out to the stop, lift the front, and pull
13
Using the THIRSTCRUSHER”
The ice dispenser
Ice dispenses from the ice maker storage bin in the
freezer. When you press the dispenser bar, a trapdoor
opens in a chute between the dispenser and the ice bin. Ice moves from the bin and falls through the chute. When you release the dispenser bar, a buzzing sound may be heard for a few seconds as the trapdoor closes. The dispenser system will not operate when
the freezer door is open.
For crushed ice, cubes are crushed before being dispensed. This may cause a slight delay when dispensing crushed ice. Noise from the ice crusher is normal, and pieces of ice may vary in size.
When changing from CRUSHED to CUBED, a few ounces of crushed ice will be dispensed along with the
first cubes.
To dispense ice:
1. For cubed ice,
position.
move Ice Selector Switch to CUBED
dispensing
Personal Injury Hazard
Tumbling ice and pressure can break a fragile glass. Use a sturdy glass when dispensing ice or water.
Failure to do so could result in personal injury or breakage.
system
For crushed ice,
CRUSHED position.
2.
Press a Hold glass close to dispenser opening so ice does
not fall outside of glass.
3. Remove the glass to stop dispensing.
NOTE:
flavor from new plumbing and parts. Throw the ice away. Also, take large amounts of ice from the ice bin, not through the dispenser.
sturdy
The first few batches of ice may have an off-
move Ice Selector Switch to
glass against the ice dispenser bar.
14
The water dispenser
Chilled water comes from a tank behind the meat drawer. It holds approximately 1 l/2 quarts (1.5 L).
When the refrigerator is first hooked up, press the
water dispenser bar with a glass or jar until you draw
and discard two or three quarts (1.9 to 2.8 L). The
water you draw and discard rinses the tank and pipes.
Allow several hours to chill a new tankful.
NOTE:
signed to evaporate
this tray.
To dispense water:
1.
The small tray beneath the dispenser is de-
small
spills. There is no drain in
Do not
Press a
pour water into it.
sturdy
glass against the water
dispenser bar.
2. Remove the glass to stop dispensing.
NOTE:
Dispense enough water every week to maintain
a fresh supply.
The dispenser light
To turn on night light,
to the left. See page 21 for directions for changing the dispenser light bulb.
slide dispenser LIGHT switch
Solving common ice dispenser problems
PROBLEM Ice dispenser will
not work
POSSiBLE CA&/SOLUTION
l
Freezer door is open.
l
Ice bin not properly installed. Make sure the bin is pushed in all the way.
Ice dispenser stops
working
l
Wrong ice in bin. Only use crescents from the ice maker. Shake the bin occasionally to separate cubes and increase storage room.
l
Dispenser not used for extended periods of time, causing ice cubes to melt
together. Dump old ice and make a new supply.
l
Ice dispenser bar held in too long. Wait about three minutes for dispenser motor to reset.
l
Large amounts of ice should be taken from the bin, not through the dispenser.
15

Using the automatic ice maker

Here are a few things you will want to know about your automatic ice maker:
l
The ON/OFF lever is a wire signal arm. Move arm:
DOWN to make ice automatically. UP to shut off the ice maker.
NOTE:
to the water supply.
water supply hookup are attached to the back of the refrigerator cabinet.
l
It is normal for ice crescents to be attached by a corner. They break apart easily.
l
The ice maker will not operate until the freezer is cold enough to make ice. This can take overnight.
l
If ice is not being made fast enough and more ice is needed, turn the Refrigerator Control toward a higher number. Wait a day and, if necessary, turn the Freezer Control toward C.
l
Good water quality is important for good ice quality. Try to avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt from a malfunctioning softener) can damage the ice maker mold and lead to poor ice quality. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.
Do not turn ice maker on until it is connected
Instructions for ice maker
UP to
stop ice
maker.
DOWN to
start Ice
maker.
Solving common ice maker problems
PROBLEM Ice crescents attached
at corners Ice maker will not
operate or ice is not made fast enough
Off-taste or odor in ice
POSSIBLE CAUSE/SOLUTION
l
This is normal. They break apart easily. Shake bin occasionally to keep cubes separated.
l
ON/OFF lever is in the OFF (up) position. Lower lever to the ON (down) position.
l
Freezer is not cold enough. Adjust temperature controls and wait 24 hours.
(See “Changing the control settings” on page 7.)
l
New plumbing connections can cause discolored or off-flavored ice. Discard
the first few batches of ice.
l
Cubes are stored too long. Throw them away and make a new supply.
l
Food is not wrapped properly. See page 25.
l
Freezer and ice bin need to be cleaned. See page 23.
l
Water may contain minerals (such as sulfur). A filter may be required to remove them.
16

Removing the ice maker storage bin

Remove, empty, and clean the storage bin if:
l
The ice dispenser has not, or will not, be used for a
week or more
l
A power failure causes ice in the bin to melt and
freeze together
l
The ice dispenser is not used regularly
To remove ice bin:
1.
Pull the covering panel out from the bottom and
slide it to the rear.
2. Lift the signal arm so it clicks into the OFF (up) position. Ice can still be dispensed, but no more
can be made.
3. Lift the front of the storage bin and pull it out.
4. Empty the ice bin. Use hot or warm water to melt the ice if necessary.
Never use anything sharp
to break up ice in the bin. This can damage the bin and dispenser mechanism.
5. Wash with mild detergent. Rinse well. Do not use harsh or abrasive cleaners or solvents.
6. When replacing the bin, make sure it is pushed in all
the way. Then push the signal arm down to the ON
position to restart ice production.
17

Attaching the ice maker to a water supply

Read all directions carefully before you begin.
IMPORTANT:
. It may take up to 24 hours for your ice maker to
Electrical Shock Hazard
Disconnect electrical supply to refrigerator before installing.
Electrical drill must be grounded before drilling holes in water line.
Failure to do so could result in death, electrical shock, or serious injury.
begin producing ice.
l
If operating the refrigerator before installing the water connection, turn ice maker to the OFF position to prevent operation without water.
l
All installations must be in accordance with local plumbing code requirements.
IMPORTANT:
l
Use copper tubing only and check for leaks.
l
Install ice maker tubing in areas where temperatures are above freezing.
Tools required:
l
Standard screwdriver
l
‘he-inch and N-inch open-end wrenches or two adjustable wrenches
l
X-inch nut driver
l
%-inch drill bit
l
Hand drill or electric drill (properly grounded)
NOTE:
Your appliance dealer has a kit available with a X-inch saddle type shut-off valve, a union, and copper tubing. Before purchasing, make sure a saddle type valve complies with your local plumbing codes. Do not use piercing type or %-inch saddle valve which
reduces water flow and clogs more easily.
Cold water supply
Ice maker water valve contains a flow washer which is
used as a water pressure regulator. The ice maker
needs to be connected to a cold water line with water pressure limitations of 20-l 20 psi. If a problem occurs,
call your utility company.
INSTALLATION IS NOT WARRANTED
BY REFRIGERATOR OR ICE MAKER
MANUFACTURER.
18
Connecting to water line
Find a s-inch to 1 X-inch vertical COLD water pipe
1.
near the refrigerator.
NOTE:
precaution must be taken: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve.
Measure from connection on rear of refrigerator to
2.
water pipe. Add seven feet (2.1 m) to allow for
moving refrigerator for cleaning. This is the length of X-inch O.D. copper tubing you will need for the job (length from connection to water pipe PLUS seven feet [2.1 ml). Be sure both ends of copper tubing are cut square.
3. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.
4. Using a grounded drill, drill a %-inch hole on the cold water pipe you have selected.
5. Fasten shut-off valve to cold water pipe with pipe clamp. Be sure outlet end is solidly in the X-inch drilled hole in the water pipe and that washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not over-tighten or you may crush the copper tubing, especially if soft
(coiled) copper tubing is used. Now you are ready to
connect the copper tubing.
6. Slip compression sleeve and compression nut on
copper tubing as shown in diagram. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjust­able wrench. Do not overtighten. Turn ON main water supply and flush out tubing until water is clear. Turn OFF shut-off valve on the water pipe. Coil copper tubing.
Horizontal pipe will work, but the following
Vertical cold water pipe
Washer
/
sleeve
*Controls water supply
%-Inch O.D. copper tubing (length from
Inlet on rear of
nut
TO REFRIGERATOR +
Connecting to refrigerator
1.
(On kit models, assemble water valve to refrigerator per kit instructions.) Route the copper tubing through the tube clamp provided as shown at right. Connect the X-inch copper tube from the shut-off valve to the water valve at the lower, left rear of cabinet. Remove tape label from valve inlet and insert tubing until it
bottoms out (approximately 1/2 inch). Tighten nut by hand as much as possible; then turn the nut an additional l/2 turn using a wrench. Do not overtighten.
2. Turn shut-off valve ON. CHECK FOR LEAKS. TIGHTEN ANY CONNECTIONS (INCLUDING
CONNECTIONS AT THE VALVE) OR NUTS
THAT LEAK.
3. The ice maker is equipped with a built-in water
strainer. If local water conditions require periodic cleaning or a well is your source of water supply, a second water strainer should be installed in the %-inch water line. Obtain a water strainer from your nearest appliance dealer. Install at either tube connection.
4. Reconnect electrical supply to refrigerator.
Water Inlet
19

Removing the base grille

To remove the grille:
1.
Open both doors.
2. Pull base grille forward to release the support tabs from the metal clips.
3.
Do not remove Tech Sheet
the grille.
To replace the grille:
1.
Line up grille support tabs with metal clips.
2. Push firmly to snap into place.
3. Close the doors.
See cleaning instructions for defrost pan and con­denser coils on page 23.
fastened behind

Changing the light bulbs

Electrical Shock Hazard
Before removing a light bulb, either unplug the refrigerator or disconnect the electricity leading to
it at the main power supply.
Failure to do so could result in personal injury.
To change refrigerator light:
1.
Disconnect refrigerator from power supply.
2. Reach behind the Control Console to remove bulb.
3. Replace bulb with a 40-watt appliance bulb.
4. Reconnect refrigerator to power supply.
To change crisper light:
1.
Disconnect refrigerator from power supply.
2. Pull top of light shield forward until it snaps free.
3. Lower light shield to clear bottom supports.
4. Pull light shield straight out to remove.
5. Replace bulb with a 40-watt appliance bulb.
6. Replace light shield in reverse order.
7. Reconnect refrigerator to power supply.
isper
light
20
To change light below ice bin:
1.
Disconnect refrigerator from power supply.
2. Push in sides of light shield and pull forward until shield snaps free.
3. Replace bulb with a 40-watt appliance bulb.
4. Replace light shield.
5. Reconnect refrigerator to power supply.
To change light behind quick freeze compartment (on some models):
1.
Disconnect refrigerator from power supply.
2. Lift and secure quick freeze compartment door.
3. Remove top freezer shelf by lifting up and sliding out.
4. Remove light shield by grasping the top center of the shield.
5. Pull forward while turning the light shield slightly to one side.
6. Replace bulb with a 40-watt appliance bulb.
7. To replace light shield:
l
Grasp the top center of the shield.
l
Insert the tabs on one end of the shield into the slotted holes in the freezer liner.
l
Carefully bend the shield at the center to insert the tabs on the other end.
6. Replace top freezer shelf.
9. Reconnect refrigerator to power supply.
Light
below
ice bin
Light dehind quick freeze compartment
To change dispenser area light:
1.
Disconnect refrigerator from power supply.
2. Reach through dispenser area to remove bulb.
3. Replace with a heavy-duty lo-watt bulb, which can be purchased from your Whirlpool dealer.
4. Reconnect refrigerator to power supply.
NOTE:
Not all commercial appliance bulbs will fit your refrigerator. Be sure to replace a bulb with one of the same size and shape.
Dispenser area light
21

Understanding the sounds you may hear

Your new refrigerator may make sounds that your old one didn’t. Because the sounds are new to you, you might be concerned about them. Don’t be. Most of the new sounds are normal. Hard surfaces like the floor, walls, and cabinets can make the sounds seem louder. The following describes the kinds of sounds that might be new to you, and what may be making them.
Slight hum, soft hiss
You may hear the refrigerator’s fan motor and
moving air.
Clicking or snapping sounds
The thermostat makes a definite click when the refrig­erator stops running. It also makes a sound when the
refrigerator starts. The defrost timer will click when the
defrost cycle starts.
Water sounds
When the refrigerator stops running, you may hear gurgling in the tubing for a few minutes after it stops. You may also hear defrost water running into the defrost water pan.
Ice maker sounds
l
trickling water
l
thud (clatter of ice)
You may hear buzzing (from the water valve), trickling water, and the clatter of ice dumped into the bin.
Running sounds
Your refrigerator has a high-efficiency compressor and motor. It will run longer than older designs. It may even seem to run most of the time.

Saving energy

You can help your refrigerator use less electricity.
l
Check door gaskets for a tight seal. Level the cabinet to be sure of a good seal.
l
Clean the condenser coils regularly.
l
Open the door as few times as possible. Think about what you need before you open the door. Get every­thing out at one time. Keep food organized so you won’t have to search for what you want. Close door as soon as food is removed.
l
Go ahead and fill up the refrigerator, but don’t overcrowd it so air movement is blocked.
l
It is a waste of electricity to set the refrigerator and freezer to temperatures colder than they need to be. If ice cream is firm in the freezer and drinks are as cold as your family likes them, that’s cold enough.
l
Make sure your refrigerator is not next to a heat source such as a range, water heater, furnace, radiator, or in direct sunlight.
22

Caring for Your Refrigerator

Your refrigerator is built to give you many years of dependable service. However, there are a few things you can do to help extend its product life. This section tells you how to clean your refrigerator and what to do when going on vacation, moving, or during a power outage.
Cleaning your refrigerator
Both the refrigerator and freezer sections defrost
automatically. However, clean both about once a month to help prevent odors from building up. Wipe up spills right away.
’ .
q
To clean your refrigerator, unplug it,
take out all removable parts, and clean
the refrigerator according to the following directions.
Refrigeration system tubes are near the defrost pan and can become hot. Remove and install defrost pan carefully.
Failure to do so could result in personal injury.
Personal Injury Hazard
PART Removable parts
(shelves, crisper, etc.)
Outside
Inside walls
(allow freezer to warm up so cloth won’t stick)
Door liners and gaskets
Plastic parts
(covers and panels)
Defrost pan
WHAT TO USE HOW TO CLEAN
l
Sponge or cloth with mild
Hand wash, rinse, and dry thoroughly.
detergent and warm water
l
Sponge, cloth, or paper towel with mild detergent, warm water, and a good appliance wax (or good auto paste wax)
Sponge, soft cloth, or paper towel with baking soda or
Wash outside of cabinet. Do not use abrasive or harsh cleaners.
l
Wipe and dry thoroughly.
l
Wax painted metal surfaces at least twice a year. Apply wax with a clean, soft cloth.
metal surfaces provides rust protection. Do not wax plastic parts.
l
Wash with mixture of warm water and:
Waxing painted
- mild detergent, or mild detergent and warm - baking soda (two tbs to one qt [26 g to .95 L] water
Sponge, soft cloth, or paper towel with mild detergent and warm water
Soft, clean sponge or soft, clean cloth with mild deter­gent and warm water
Sponge or cloth with mild detergent and warm water
of water).
l
Wipe and dry thoroughly.
l
Wash, wipe, and dry thoroughly.
DO NOT USE cleaning waxes, concentrated detergents, bleaches, or cleaners containing petroleum on plastic parts.
l
Wash, wipe, and dry thoroughly.
DO NOT USE paper towels, window sprays, scouring cleansers, or flammable fluids. These can scratch or damage material. See “Important Safety Instructions” on page 2.
l
Remove base grillle. (See page 20.)
l
Reach into small opening at right edge and remove
the defrost pan.
Condenser coils
Vacuum cleaner with extended narrow attachment
l
Wash, rinse, and ‘dry thoroughly.
l
Replace defrost pan. Make sure to push it com-
pletely into the opening.
l
Replace base grille.
l
Remove base grille.
l
Vacuum coils when dusty or dirty. Coils may need to be cleaned as often as every other month.
l
Replace base grille.
2:
Vacation and moving care
Short vacations
No need to shut off the refrigerator if you will be away
for less than four weeks.
1. Use up any perishables.
2. Freeze other items.
3. Raise signal arm to OFF (up) position.
4. Shut off water supply to the ice maker.
5. Empty the ice bin.
Long vacations
If you will be gone a month or more:
1.
Remove all food from the refrigerator.
2. Turn off the water supply to the ice maker at least one day ahead of time.
3. When the last load of ice drops, turn off the ice maker. Make sure all ice is dispensed out of the ice
maker mechanism.
4. Unplug the refrigerator.
5. Clean it, wipe, and dry well.
6. Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and mold from building up.
Moving
When you are moving the refrigerator to a new home:
1.
Turn off the water supply to the ice maker at least one day ahead of time.
2. Disconnect the water line.
3. After the last load of ice drops, lift the signal arm to the OFF (up) position.
4. Remove all food from the refrigerator.
5. Pack all frozen food in dry ice.
6. Unplug the refrigerator.
7. Clean it thoroughly. Wipe and dry well.
8. Take out all removable parts, wrap them well, and tape them together so they don’t shift and rattle.
9. Screw in the leveling rollers.
10.
Tape the doors shut and tape the power supply cord to the cabinet.
When you get to your new home, put everything back and refer to page 6. Also, if your refrigerator has an automatic ice maker, remember to reconnect the water supply line.
Personal Injury Hazard
Do not allow children to climb on, play near, or climb inside the refrigerator when the doors are blocked open.
They may become injured or trapped.
To restart refrigerator, see page 7.
Power interruptions
If electricity goes off, call the power company. Ask how long power will be off.
1.
If service will be interrupted 24 hours or less,
both doors closed.
2. If service will be interrupted longer than 24 hours: (a) Remove all frozen food and store in a frozen
food locker. OR (b) Place two Ibs (907 g) of dry ice in freezer for
every cubic foot (liter) of freezer space. This will
keep food frozen for two to four days. Wear
gloves to protect your hands from dry ice burns. OR (c) If neither a food locker or dry ice is available,
use or can perishable food at once.
This helps foods stay frozen.
keep
3. A full freezer stays cold longer than a partly filled one. A freezer full of meat stays cold longer than a freezer full of baked goods. If food contains ice crystals, it may be safely refrozen, although the quality and flavor may be affected. If the condition of the food is poor, or if you feel it is unsafe, dispose of it.
Questions?
Call our Consumer Assistance Center telephone number, l-800-253-1301, from anywhere in the U.S.A.
24

Food Storage Guide

There is a correct way to package and store refrigerated or frozen food. To keep food fresher, longer, take the time to study these recommended steps.
Storing fresh food
Wrap or store food in the refrigerator in airtight and moisture-proof material. This prevents food odor and taste transfer throughout the refrigerator. For dated products, check code date to ensure freshness.
Butter or margarine
Keep opened butter in covered dish or closed compartment. When storing an extra supply, wrap in freezer packaging and freeze.
Leafy vegetables
Remove store wrapping and trim or tear off bruised and discolored areas. Wash in cold water and drain. Place in plastic bag or plastic container and store in crisper.
Vegetables with skins
(carrots,
Store in crisper, plastic bags, or plastic container.
peppers)
Fruit
Wash, let dry, and store in refrigerator in plastic bags or crisper. Do not wash or hull berries until they are ready to use. Sort and keep berries in original container in a crisper, or store in a loosely closed paper bag on a
refrigerator shelf.
Eggs
Store without washing in original carton on interior shelf.
On some models, an egg storage container is provided for your convenience.
Milk
Wipe milk cartons. For best storage, place milk on
interior shelf.
Cheese
Store in the original wrapping until you are ready to use it. Once opened, rewrap tightly in plastic wrap or alumi­num foil.
Leftovers
Cover leftovers with plastic wrap or aluminum foil. Plastic containers with tight lids can also be used.
Meat
Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following for storage times. When storing meat longer than the times given, freeze the meat.
Chicken . . . . . . . . . . . .
Ground beef
Steaks/roasts . . . . 3-5 days
l-2 days Bacon . . . . . . . . . . . . . . . . . .
. . . . . l-2 days
Cold cuts . . . . . . . . . . . . .
Variety meats . . . . . . l-2 days
Cured meats . . . 7-10 days NOTE: Use fresh fish and shellfish the same day as
purchased.
5-7 days 3-5 days
Storing frozen food
The freezer section is designed for storage of commer-
cially frozen food and for freezing food at home.
NOTE:
freezing or food storage times, check a freezer guide or
reliable cookbook.
Packaging
The secret of successful freezing is in the packaging.
The way you close and seal the package must not
allow air or moisture in or out. Packaging done in any
other way could cause food odor and taste transfer
throughout the refrigerator and drying of frozen food.
Packaging recommended for use:
l
l
l
l
l
Follow package or container instructions for proper freezing methods.
For further information about preparing food for
Rigid, plastic containers with tight-fitting lids
Straight-sided canning/freezing jars
Heavy-duty aluminum foil Plastic-coated paper Non-permeable plastic wraps (made from Saran film)
Do not use:
l
Bread wrappers
l
Non-polyethylene plastic containers
l
Containers without tight lids
l
Wax paper
l
Wax-coated freezer wrap
l
Thin, semi-permeable wrap
The use of these wrappings could cause food odor, taste transfer, and drying of frozen food.
Freezing
Do not expect your freezer to quick-freeze any large quantity of food. Put no more unfrozen food into the freezer than will freeze within 24 hours (no more than two to three Ibs of food per cubic foot [907-l ,350 g per liter] of freezer space). Leave enough space for air to circulate around packages. Be careful to leave enough room at the front so the door can close tightly.
Storage times will vary according to the quality of the food, the type of packaging or wrap used (airtight and moisture-proof), and the storage temperature, which should be 0°F (-17.8%).
25

Troubleshooting

Performance problems often result from little things you can fix without tools. Please read through “Before calling
for assistance . . .‘I
Before calling for assistance . . .
Listed in this chart are the most common problems consumers run into with their appliances. Please read through
this and see if it can solve your problem.
below before calling for service on your appliance.
PROBLEM Your refrigerator
will not operate
The lights do not work
The ice maker does not work
Dispensers do not work
Unfamiliar sounds or a rattling/
jingling noise
There is water in the defrost pan
CHECK THE FOLLOWING
Is the power supply cord firmly plugged into a live circuit with proper voltage? Has a household fuse or circuit breaker blown/tripped? Is the Refrigerator Control set to the OFF position? Is the power supply cord firmly plugged into a live circuit with proper voltage? Has a household fuse or circuit breaker blown/tripped? Is a bulb burned out? Is the freezer cold enough to make ice? It could take overnight for the freezer to reach
the proper temperature.
Is the ON/OFF lever in the ON (down) position? (See page 16.) Is the water valve turned on? Does the water line have a clog or leak? Is the freezer door closed?
Is something on top of or behind the refrigerator?
Some new sounds are normal. See “Understanding the sounds you may hear” on
page 22.
This is normal on hot, muggy days. Make sure the refrigerator is level so the pan does
not overflow.
1
The motor seems to run too much
Are the condenser coils dirty?
Has the door been opened often? Has a large amount of food been added at one time? The motor naturally runs longer if these things happen.
Is the room hot? If the room is too warm, the motor runs longer to keep the unit cool.
26
Reauestina Assistance or Service
- -w -~ - - - u
Before calling for assistance or service, please check “Troubleshooting” on page 26. It may save you the service call. If you still need help, follow the instructions below.
For assistance or service in the U.S.A.:
1. If you need assistance+ . . .
Call the Whirlpool Consumer Assistance Center
r-1 telephone number. Dial toll-free from
. ~ 1 anywhere in the U.S.A.:
1-800-253-l 301
and talk with one of our trained consult-
ants. The consultant can instruct you in how to obtain satisfactory operation from your appli­ance or, if service is necessary, recommend a qualified service company in your area.
If you prefer, write to:
Mr. William Clark Consumer Assistance Representative Whirlpool Corporation
2000
North M-63
Benton Harbor, Ml 49022-2692
Please include a daytime phone number in your correspondence.
2. If you need service+ . . .
Whirlpool has a nationwide network of authorized
Whirlpool service companies. Whirlpool service technicians are trained to fulfill
SERVICE
Ii3 Whirlpool service company in your area, call our Consumer Assistance Center telephone number (see Step 1) or look in your telephone directory Yellow
Pages under:
‘APPLIANCE-HOUSEHOLD
MAJOR, SERVICE IL REPAIR
-Seer Whirlpool Appliances or Authorized Whirlpool Service (ExampIer XYZ service CO.)
the product warranty and provide after­warranty service, anywhere in the United States. To locate the authorized
*WASHING MACHINES IL
DRYERS, SERVICE & REPAIR
- See: Whirlpool Appliances or Aulhormd Whirlpool Service (Example: XYZ Service Co.)
3. If you need FSP* replacement parts . . .
FSP is a registered trademark of Whirlpool Corpora­tion for quality parts. Look for this symbol of quality whenever you need a replacement part for your
WHIRLPOOL’ appliance. FSP replacement parts will fit
right and work right, because they are made to the
same exacting specifications used to build every new
WHIRLPOOL appliance.
To locate FSP replacement parts in your area, refer to Step 2 or call the Whirlpool Consumer Assistance Center number in Step 1.
4. If you are not satisfied
with how the problem
was solved . . .
l
Contact the Major Appliance Consumer Action
Program (MACAP). MACAP is a group of indepen­dent consumer experts that voices consumer views at the highest levels of the major appliance industry.
l
Contact MACAP only when the dealer, authorized servicer, and Whirlpool have failed to resolve your
problem.
Major Appliance Consumer Action Program 20 North Wacker Drive Chicago, IL 60606
l
MACAP will in turn inform us of your action.
cost Of
a
+When asking for help or service:
Please provide a detailed description of the problem, your appliance’s complete model and serial numbers, and the purchase date. (See page 1.) This information will help us respond properly to your request.
27
For assistance or service in Canada:
1. If the problem is not due to one of the items listed in
“Troubleshooting”...
Contact the dealer from whom you purchased
your appliance,or your nearest lnglis Limited Appliance Service Branch. Please include a daytime phone number in your correspondence.
lnglis Limited Appliance Service - Consumer Services
Direct service branches:
BRITISH COLUMBIA Vancouver
Victoria
ALBERTA Calgary
Edmonton
ONTARIO
Toronto
(Mlsslssauga) Toronto
(Markham) Ottawa
*
2. If you need service . . .
Contact your nearest lnglis Limited Appliance
Service Branch or an authorized servicing outlet.
lnglis Limited Appliance Service 3627 E. 4th Avenue
lnglis Limited Appliance Service 3117 Steele Street
lnglis Limited Appliance Service #15, 6025 12th Street S.E.
lnglis Limited Appliance Service 16236 116th Avenue
lnglis Limited Appliance Service 5945 Ambler Drive
lnglis Limited Appliance Service Unit #l , 110 Torbay Road
lnglis Limited Appliance Service 26 Capital Drive
(604) 291-6426
1-600-665-6766
(604) 383-2298
1-600-665-6766
(403) 453-9267
l-600-661 -1022
(403) 453-3900
l-600-661 -6291
(905) 821-3900
l-600-807-6777
(905) 475-9511
l-600-607-6777
(613) 225-0510
l-800-267-3456
MANITOBA
SASKATCHEWAN QUEBEC
NOVA SCOTIA
Winnipeg lnglis Limited Appliance Service
Montreal (Laval)
Brossard
Quebec city
Sherbrooke (Rock Forest)
Dartmouth
For service in areas other than those listed, contact your Appliance Dealer.
1663 Church Avenue lnglis Limited Appliance Service
2750 Francis Hughes
lnglis Limited Appliance Service
9605 F. lgnace Street
lnglis Limited Appliance Service
5275 Blvd. Wilfrid Hamel, Suite 140
lnglis Limited Appliance Service
3475 Industrial Blvd.
lnglis Limited Appliance Service
900 Windmill Road
(204) 694-5308
l-600-665-1 663 (514) 3626110
l-800-361 -3032
(514) 397-l 640
l-600-361 -0950
(416) 671-5251
l-600-463-1 523
(819) 564-6565
l-600-567-6966
(902) 4666634
l-600-565-1 596
28
Loading...
+ 65 hidden pages