Whirlpool ECKMF-86 Installation Instructions Manual
1108108
HOW TO INSTALL
YOUR AUTOMATIC ICE MAKER
ECKMF-86
KEEP ALL PARTS IN THEIR OWN PACKAGE UNTIL NEEDED
PARTS ARE LISTED BY STEPS IN WHICH THEY ARE USED. ARRANGE IN ORDER BEFORE STARTING
INSTALLATION. REFER TO SERVICE PARTS LIST FOR INDIVIDUAL REPLACEMENT PARTS.
PART
USED IN
NUMBER
NAME QUANTITY STEP NUMBEI
# 1 944811
WIRING ASSEMBLY
1 4, 13
# 2 836489
WATER TUBE FllTlNG
1 3
# 3 470168
GRAY SEALER (PERMAGUM)
1 3
# 4 939027
WATER INLET TUBE (ALUMINUM)
1 13
# 5 489069
SCREW, STAINLESS (NO. 8 x
l/2”)
1 15
# 6 627910
WATER VALVE ASSEMBLY
1 5, 6, 7, 9
# 7 939529
ICE BUCKET
1 15
if 8 488878 CLAMP 1 11
# 9 488645
SCREWS, SHEET METAL (NO. 8 x
l/2”)
4 8, 9, 10, 11
#lO 841707
TUBE INSERT
1 11
#l 1 488366
CLAMPS
2 10
#12 488649
SCREW, SELF TAPPING (NO. 8-32 x l/z”) 2
9
#13 549193
CLAMP
1 10
#14 946335
PLASTIC TUBE ASSEMBLY
1 6, 11
#15 627886
COPPER TUBE ASSEMBLY
1
7
Water hook-up parts available from your Whirlpool dealer or local hardware store.
Installation Steps
These instruclions cover models wilh and without a condenser coil
on the back of the cabinet. See illustrations below and
follow instructions thal apply to your model
1
Unplug Electric Plug
From Outlet
Tools and Other Items You Will Need
2
Install Water Tube
TOOIS
Waler Hook Up
l-Phillips head screwdriver (Malerials needed, not included in Ice Maker Kit.)
1 -Pliers
j/4” O.D. Copper Tubing-See step 2 (back page)
I
1-W’ nut driver
Or
for length.
1 -Shut-off Valve-%” outlet
I
6” flat blade screwdriver l-Tube &won--1/4” x l/4”
I\
11
Plastic Tube
II
Connection -
Place Clamp onto inlet
tube.
Place tuba insert in end
of tube and slide into
inlet tuba, tighten clamp.
NOTE: Excess tube can
be cut off; ba sure to
allow line to go into tube
for full length of Insert.
10
Attach Wire
and Water
ThS par! may De
on your reehgmta
,3
Remove 2 Screws
(save for reuse)
Remove Water Fill Cover
4
Install Wiring Harness
-Remove wring hole cover. Pull insert pad from
cabinet hole and place around wires.
1 Push wiring harness #l into hole, being sure
grommet seals flush to prevent air entry
Connect plug firmly into receptacle.
Route wires behind condenser MIIS if present
INSTALL WATER VALVE
Connect valve wiring plug onto
5
terminals on valve coil.
Attach plastic water tube
assembly #14. Push tubing into
valve and tighten nylon nut (not
too tight) onto valve threads.
p&i tube
-8
straight up
Attach clamo with Sheet Metal
Screw #9
+9
Attach valve
with Self Tapping Screw #12.
’ 2 ~r!n?%ock-out from
fill cup facing the back
wall of freezer localed
on Ice Maker.
13
Remove Plugs and Cover
from Freezer Wall
15
Attach Ice Maker to Freezer Wall
16
Connect Ice Maker to Water Supply
Loading...