Whirlpool DU1015XTXT2, DU1015XTXS2, DU1015XTXQ2, DU1015XTXB2, MDB4630AWW4 Installation Guide

...

INSTALLATION INSTRUCTIONS

UNDERCOUNTER DISHWASHER

PLASTIC GIANT TUB MODELS

INSTRUCTIONS D'INSTALLATION

LAVE-VAISSELLE SOUS COMPTOIR

MODI_LES A TRI_S GRANDE CUVE EN PLASTIQUE

Table of Contents .............................................................. 2

Table des matieres .......................................................... 25

W10401503B

TABLE OF CONTENTS

DISHWASHER SAFETY ............................................................................... 2

INSTALLATION REQUIREMENTS ............................................................. 3

Tools and Parts ......................................................................................... 3

Location Requirements ............................................................................. 4

Drain Requirements .................................................................................. 6

Water Supply Requirements ..................................................................... 6

Electrical Requirements ............................................................................ 6

INSTALLATION INSTRUCTIONS ............................................................... 7

Prepare Cabinet Opening--Existing Utilities ............................................ 7

Prepare Cabinet Opening--New Utilities ................................................. 7

Prepare and Route Water Line ................................................................. 8

Install Drain Hose ...................................................................................... 9

Prepare Dishwasher ................................................................................ 11

Make Power Supply Cord Connection ................................................... 12

INSTALLATION INSTRUCTIONS (CONT.)

Determine Cabinet Opening ................................................................... 14

Choose Attachment Option .................................................................... 14

Prepare Water Supply Line..................................................................... 15

Move Dishwasher Close to Cabinet Opening ........................................ 15

Connect to Water Supply ....................................................................... 17

Connect to Drain ..................................................................................... 18

Make Direct Wire Electrical Connection ................................................. 18

Secure Dishwasher in Cabinet Opening ................................................ 20

Complete Installation .............................................................................. 21

Check Operation ..................................................................................... 22

If Dishwasher Does Not Operate ............................................................ 22

Additional Tips ........................................................................................ 22

DISHWASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

You Need to:

• Slowly open dishwasher door while someone grasps the rear of the dishwasher. Remove shipping materials, drain hose and

lower rack. Close dishwasher door until latched.

• Observe all governing codes and ordinances.

• Install this dishwasher as specified in these instructions.

• Installation should be performed by a qualified service technician. The dishwasher must be installed to meet all

Tip Over Hazard

Do not use dishwasher until completely installed.

electrical and plumbing national and local codes and ordinances.

Do not push down on open door. Doing so can result in serious injury or cuts.

INSTALLATION REQUIREMENTS

Parts needed:

Gather the recommended tools and parts before starting installation. Read and follow the instructions provided with any

tools listed here.

All Installations Toolsneeded:

Pliers

Phillips screwdriver

5 1

_ and V4 _,,,-_

nut drivers or _/_i_,y hex sockets 1_

or ruler

Measuring tape 10" adjustable wrench IC[_

that

opens to /_

11/8"(2.9 cm)

*Must be the proper size to connect your household wiring

to 16-gauge wiring in dishwasher.

Other useful items you may need:

Fl_sh ig Shallow _----__ Bath __ -_[

pan _--_ towel -_ I

Flat-blade screwdriver

Utility knife

UL Listed!CSA

Approved twist-on 0 _ wire connectors*

Small level S

%" open-end

wrench

%'!Comer X 3A"hose fitting For part 0r kit' see local

retailer or call Whirlpool Parts: 1-800-442.9991. Part Number W10273460

Other parts you may also need:

11/2,,.2,!

(3,81.5 cm) duct tape Screw-type

clamps (3 maximum)

Moisture Sid

barrier tape for Sol d surface (Part Numl countertops

4396277) (Part Number 8212560)

NOTE: Some parts available for purchase in plumbing supply stores. Check local codes. Check existing electrical supply. See

"Electrical Requirements" section. It is recommended that electrical connections be made by a licensed electrical installer.

In addition, for first-time installations Toolsneeded:

C_ wi

Parts supplied:

Drain hose Drain #10x½ 2, under- ClamPs (2)hose Ph II!pszhead counter (1 argeand _ screws(2) mounting

1 m I) O _ brackets

Make sure all these parts are included in the literature package.

t®TORX and T20 are registered trademarks of Saturn Fasteners, Inc.

Parts needed:

Copper tubing _y8 See "Electrical Requirements', section. O.D.suggested) or I _ ... ;, : ' _ .. _ , f exib e bra ded _or ulrect vwre: #or _'ower _upply

water suuU v ne Use UL Listed/ Cord: use UL

csA Appr0ved Listed/CSA

I Strain relief Approved power

I to fit %, (2:2 Cm)Supply Cordkit

hole marked for use with

dishWasher

Location Requirements

Grounded electrical supply required. Do not run drain lines, water lines or electrical wiring where they

can interfere with or contact dishwasher motor or legs. The location where the dishwasher will be installed must provide

clearance between motor and flooring. Motor should not touch the floor.

Do not install dishwasher over carpeted flooring. Shelter dishwasher and water lines leading to dishwasher against

freezing. Damage from freezing is not covered by the warranty. A side panel kit is available from your dealer for installing your

dishwasher at the end of your cabinetry. A moisture barrier accessory (Part Number 4396277) is available

from your dealer for installing underneath the countertop.

Check location where dishwasher will be installed. The location must provide:

• easy access to water, electricity and drain.

• convenient access for loading and unloading dishes.

Corner locations require a 2" (5.1 cm) minimum clearance

between the side of the dishwasher door and the wall or

cabinet.

• square opening for proper operation and appearance.

• cabinet front perpendicular to floor.

• level floor. (If floor at front of opening is not level with floor

at rear of opening, shims may be needed to level dishwasher.)

Helpful Tip: Be sure to accurately measure dimensions and ensure dishwasher is level if the floor in the dishwasher opening is

uneven (example: Flooring extends only partway into opening). NOTE: To avoid shifting during dishwasher operation, shims must

be securely attached to the floor. If dishwasher will be left unused for a period of time or in a

location where it may be subject to freezing, have it winterized by authorized service personnel.

Make sure pipes, wires and drain hose are within the shaded area shown in the "Product and Cabinet Opening Dimensions" section.

*insulation may

be compressed. (not used on all models)

Check that all surfaces

have no protrusions that wpuld

rohibit dishwasher installation.

NOTE: Shaded area of cabinet wails show

where utility connections may

be installed.

_Measured from the lowest point on the

underside of countertop. May be reduced to

33%" (86 cm) by removing wheels from dishwasher.

**Minimum, measured from narrowest point of opening.

©rain Requirements

A new drain hose is supplied with your dishwasher. If drain hose is not long enough, use a new drain hose with a maximum length of 12 ft (3.7 m) (Part Number 3885556) that meets all current AHAM/IAPMO test standards, is resistant to

heat and detergent, and fits the 1" (2.5 cm) drain connector of the dishwasher.

Make sure to connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.8 cm)

minimum above the floor. It is recommended that the drain hose either be looped up and securely fastened to the

underside of the counter, or be connected to an air gap.

Make sure to use an air gap if the drain hose is connected to house plumbing lower than 20" (50.8 cm) above subfloor or

floor. Use 1/2"minimum I.D. drain line fittings. If required, the air gap should be installed in accordance with

the air gap installation instructions. When you are connecting the air gap, a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet.

E)ectdca) Requirements

Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA

70 - latest edition and all local codes and ordinances. A copy of the above code standards can be obtained from:

National Fire Protection Association 1 Batterymarch Park

Quincy, MA 02169-7471

You must have:

• 120-volt, 60 Hz, AC-only, 15- or 20-amp, fused electrical supply.

• Copper wire only.

We recommend:

• A time-delay fuse or circuit breaker.

• A separate circuit.

If connecting dishwasher with a power supply cord:

Use UL Listed power supply cord kit (Part Number 4317824) marked for

use with dishwasher. Power supply cord must plug into a grounded

3 prong outlet, located in the cabinet next to the dishwasher opening. Outlet must meet all

local codes and ordinances.

If connecting dishwasher with direct wiring:

• Use flexible, armored or nonmetallic sheathed, copper wire with

grounding wire that meets the wiring requirements for your home

and local codes and ordinances.

• Use a UL Listed/CSA Approved strain relief.

Water Supp)y Requirements

A hot water line with 20 to 120 psi (188 to 862 kPa) water pressure can be verified by a licensed plumber.

120°F (49°C) water at dishwasher. 3/8"O.D. copper tubing with compression fitting or flexible

braided water supply line (Part Number 4396897RP). NOTE: 1/2"minimum plastic tubing is not recommended.

A 90 ° elbow with 3/4"hose connection with rubber washer. Do not solder within 6" (15.2 cm) of the water inlet valve.

INSTALLATION

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

INSTRUCTIONS

Prepare Cabinet Opening- Existing

Cable

i DisConnect eleCtr ical power at the fuse box 0[ Ci[cui t

3_Do you already utility

have

hookups?

If the water line and the cable extend to the locations shown, proceed to the "Install Drain Hose" section. If they do not reach far

enough, follow the instructions in the "Prepare Cabinet Opening-- New Utilities" section.

P_epa_e Cabinet Opening-- Hew

Prepare and route the electrical supply

connection will you use?

PoWer Supply Cord: I

Follow oPti0n A instrictionS I

Diiect wire:

Fo,owoptj0oB!nstwct!aoSJ

Option A, Power Supply Cord:

NOTE: A grounded 3 prong outlet is required inside a cabinet next to the dishwasher cabinet opening.

Drill a 11/2"(3.8 cm) hole in cabinet side or rear. See "Product and Cabinet Opening Dimensions" section.

Woodcabinet:Sandtheholeuntilsmooth. Metalcabinet:Coverholewithgrommetincludedwithpower

supplycordkit.

Route cable from power supply through cabinet hole (cable must extend to the right front side of cabinet opening). Tape cable to the floor in area shown. This will prohibit cable from moving when dishwasher is moved into cabinet opening.

Option B, Direct Wire:

Helpful Tip: Wiring the dishwasher will be easier if you route the cable into the cabinet opening from the right-hand side.

Drill a 1V2"(3.8 cm) hole in right-hand cabinet side or rear. See "Product and Cabinet Opening Dimensions" section.

Prepare and Route Water Line

Helpful Tip: Routing the water line through the left side of cabinet opening will make water connection easier.

Drill a V2"(1.3 cm) hole in the cabinet side or rear.

Wood cabinet: Sand the hole until smooth. Metal cabinet: Cover hole with grommet (Part Number 302797 -

not provided).

Measure overall length of copper tubing for the water supply line.

Attach the water supply line (copper tubing or flexible braided line) to the hot water line using a connection configuration that is in compliance with local codes and ordinances. The water supply to

the dishwasher should have a manual shutoff valve located under the sink.

Slowly route water supply line through hole in cabinet. (If you are using copper tubing, it will bend and kink easily, so be gentle.) It should be far enough into the cabinet opening to connect it to the dishwasher inlet on the front left side of the dishwasher.

Route water line and tape it to the floor in area shown. This will keep it from moving when dishwasher is moved into cabinet opening.

IMPORTANT: Always use a new drain hose. Check local codes to determine whether an air gap is required.

If needed, drill a 1Y2"(3.8 cm) diameter hole in cabinet wall or side of the opening closest to the sink.

Slowly turn water shutoff valve to "ON" position. Flush water into a shallow pan until clear to get rid of particles that could clog the

inlet valve. Turn shutoff valve to "OFF" position.

Route drain hose as shown through hole in cabinet to the front center of opening where drain connection will be made. Tape

drain hose to the floor in area shown. This will prohibit it from moving when dishwasher is moved into cabinet opening.

, OptionA,Wastedisposer-noairgap , OptionB,Nowastedisposer--noairgap

"OptionC,Wastedisposer_withairgap

'Option D,Nowastedisposer'withairgap

IMPORTANT:Thedrainhoseconnectionofthedisposerora wasteteemustbemadebeforethedraintrapandatleast 20"(50.8cm)abovethefloorwherethedishwasherwillbe

installed. HelpfulTip:Toreducevibrationofthehose,keepthehoseaway

fromthefloor.

Option A, Waste disposer - no air gap

1. Fit rubber end of drain hose to waste tee and cut if needed.

NOTE: Do not cut ribbed section.

2= Attach rubber end of drain hose to

waste tee with a large drain hose clamp (provided). Use pliers to squeeze clamp open and move into

position. If the drain hose was cut,

use a 1V2"to 2" (3.8 to 5 cm) screw- type clamp (not provided).

Option C, Waste disposer - with air gap

Drain trap

1. Using a hammer and screwdriver, knock plug into disposer.

2. Use needle-nose pliers to remove plug.

Attach drain hose to disposer inlet with large drain hose clamp

(provided). Use pliers to squeeze clamp open and move into position.

Option B, No waste disposer - no air gap

1. Using a hammer and screwdriver, knock plug into disposer.

2. Use needle-nose pliers to remove plug.

3. Connect rubber end of drain hose to

air gap and cut if needed.

NOTE: Do not cut ribbed section.

Attach drain hose to air gap with

large drain hose clamp (provided). Use pliers to squeeze clamp open

and move into position. If the drain hose was cut, use a 11/2"to 2" (3.8 to 5 cm) screw-type clamp (not

provided).

Use a rubber hose (not provided)

with screw-type clamps (not

provided) to connect from air gap to

disposer inlet.

Drai

Option D, No waste disposer - with air gap

Tip Over Hazard

Do not use dishwasher until completely installed. Do not push down on open door.

Doing so can result in serious injury or cuts.

iiliiliiliiliiliiliiliili¸i{¸:;!!!(;!_;i¸i!¸I!!ii !!};i 1=

Connect rubber end of drain hose to air gap and cut if needed.

NOTE: Do not cut ribbed section.

Attach drain hose to air gap with large drain hose clamp (provided). Use pliers to squeeze clamp open and move into position. If the drain

hose was cut, use a 11/2'' to 2" (3.8 to 5 cm) screw-type clamp (not provided).

Use a rubber hose (not provided) with screw-type clamps (not provided) to connect from waste tee

to air gap.

Excessive Weight Hazard

Use two or more people to move and install dishwasher.

Failure to do so can result in back or other injury.

Using the precut slots in the insulation, fasten the insulation over the molded hooks on the tub. Be sure to fasten the insulation

down on both sides of the tub. Helpful Tip: Place cardboard under dishwasher until installed in

cabinet opening to avoid damaging floor covering. Do not use door panel as a worktable without first covering with a towel to

avoid scratching the door panel.

Using 2 or more people, grasp sides of dishwasher door frame and place dishwasher on its back.

Install a UL Listed/CSA Approved strain relief. Make sure screw heads are facing to the left when tightening conduit nut. Strain

relief is provided with the power supply cord kit.

Direct W re:

' .......... Follow QptJon B instructions

NOTE: If using Option B, proceed to "Determine Cabinet Opening," to continue with the installation of your dishwasher.

Using a flat-blade screwdriver, turn the plastic fasteners 1/4turn counterclockwise to unlock them. Remove panel. Do not remove tech sheet from access panel.

Using a 1/4"hex head socket, nut driver or Torx _T20 screwdriver, remove terminal box cover. Retain for later use.

® ®

Make Power Supply Cord Connection

Option A, Power Supply Cord:

Route cord so that it does not touch dishwasher motor to lower part of dishwasher tub. Pull cord through strain relief interminal

box.

Select UL Listed/CSA Approved twist-on wire connectors rated to connect your power supply cord to 16-gauge dishwasher wiring.

Connect wires black to black and white to white, using UL Listed/CSA Approved twist-on wire connectors.

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Connect wire

urounu ............... .....................................

d O

_ashe)

If needed, see website for animated representation of this step. Visit www.whirlpool.com/electrical under FAQ tab.

Tighten strain relief screws to secure cord.

Remove the green grounding screw and place through the ring terminal of the green ground wire. Reattach and tighten the green

screw.

Power Cord--Connect

J '_

remaining wires

' /

NOTE: Do not pre-twist stranded wire. Twist on wire connector. Gently tug on wires to be sure both are secured.

Place wires inside terminal box. Insert tabs on left side of cover. Make sure wires are tucked inside box. Close cover ensuring

wires are not pinched. Use 1/4"nut driver or Torx®T20®screwdriver and previously removed screw to secure cover.

NOTE: Do not plug into outlet until instructed to do so.

Determine Cabinet Opening

Measure height of cabinet opening from underside of countertop to floor where dishwasher will be installed (you will need to measure the lowest point on the underside of the countertop and

the highest point on the floor). Refer to "Dishwasher Height Adjustment Chart" for wheel position and the number of turns

needed.

33%" (86,0 cm) Removed All the way up

341/2"(87,6 cm) i 3 I 0

NOTE: If the minimum cabinet opening height is less than 34" (86.4 cm), the rear wheels can be removed for additional

clearance. This will allow the dishwasher to fit into a 337/8'' (86 cm) high cabinet opening, but the dishwasher will be more difficult to move. (Measurements are approximate. Wheels and legs are

preset at the factory for 341/2"[87.6 cm].)

Adjust wheels and legs

Built-up floors: If the kitchen floor is higher than the cabinet opening's floor - for example, the kitchen floor tile does not extend into the cabinet opening - add shims as needed in the area

shown to bring the dishwasher up to 34" (86.4 cm) below the countertop.

NOTE: Shims must be securely attached to floor to avoid movement when the dishwasher is in use.

Choose Attachment Option

Excessive Weight Hazard

Use two or more people to move and install dishwasher.

Failure to do so can result in back or other injury.

Turn both leveler legs to the same height. Put wheels in the required position determined from "Dishwasher Height Adjustment Chart." To change wheel position, use a flat-blade

screwdriver to pop out the wheel, then snap into the new position.

Using 2 or more people, stand the dishwasher up. IMPORTANT: The dishwasher must be secured to the cabinet. There are two brackets found in the parts bag. Attach the

brackets using Option Number 1 if the countertop is wood, laminate or another similar surface. If your countertop is marble,

granite or another hard surface, install using Option Number 2.

Option1,CountertopAttachment

Remove the brackets from the package and insert into the open slots on the left and right-hand top of the dishwasher collar as

shown.

Connect the 3/8"compression fitting to the water supply line prior to installing the unit into the cabinet opening. Attach such that the

3/4"connection is facing upward as shown above. Copper tubing only: Put the tubing into the 90° elbow fitting as far

as it will go (the copper tubing bends and kinks easily). Slide the nut and ferrule forward and start the nut onto the elbow threads.

Flexible braided connection: Secure nut to elbow using 5/8"open ended wrench or adjustable wrench.

NOTE: Do not use Teflon ®ttape with compression fittings.

Move Dishwasher C ose to Cabinet

Using a pair of pliers, bend the tab down to secure the bracket in place. Repeat this step for the other side.

NOTE: Do not attach the dishwasher. This will be done later.

Option 2, Side Attachment

For marble, granite, or other hard surface countertops

Order Mounting Bracket Kit Part Number 8212560.

Prepare Water Supply Line

tu ,n0,co00ertu ,n0

Copper tubing only: Slide nut, then ferrule, about 1" (2.5 cm) onto copper tubing.

NOTE: To avoid vibration during operation, route the water supply line so that it does not touch the dishwasher base, frame or motor.

Excessive Weight Hazard

Use two or more people to move and install dishwasher.

Failure to do so can result in back or other injury.

NOTE: Do not install kick plate until instructed to do so

)

IMPORTANT: Double-check correct placement of utilities. Grasp the sides of the dishwasher at the edges of the door panel. Tilt

dishwasher backward on wheels and move dishwasher close to cabinet opening.

NOTE: Do not push on the front of the panel or on the console. Panel or console may dent.

Helpful Tip: Temporarily tape utilities to the floor in the locations shown to prohibit them from moving when dishwasher is moved

into the cabinet opening.

1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

+ 33 hidden pages