Page 1
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
EN
Quick guide
DEMO
1
3
2
9
7
8
4 56
3’’
3’’
h
In order to receive a more complete assistance,
please register your product on
www.whirlpool.com.sg
Before using the appliance carefully read the Safety Instructions.
Before using the appliance carefully read the Safety Instructions.
CONTROL PANEL
1 ON/OFF button (Reset if long pressed)
2 Programme selection Knob
3 Start/Pause
Options buttons*
4 Dryness level
5 Start delay
6 Timed drying
7 Cycle end
8 Rapid (Key lock if long pressed)
9 Fresh care+ (Mute if long pressed)
2
INDICATORS
Cycle phase: Drying - Cool down - End of cycle.
Empty water tank - Clean door lter - Clean bottom lter -
Refer to Troubleshooting section: Failure: Call after sales service
*Note: some models may have the wording in full instead of the icons
Demo mode
h
4 56
9
3’’
8
3’’
7
1
3
FIRST TIME USE
Make sure that the water tank is correctly inserted. Make sure
that the drain hose on the back of the dryer is xed correctly,
either to the dryer’s water tank, or to your domestic sewage
system.
DAILY USE
Doing this will keep your machine working at its BEST!
Remember to empty your water tank after each drying cycle.
Remember to clean your lters after each drying cycle. (Refer
to section Care & Maintanence).
1. Open the door and load garments. Always refer to instructions
on clothing labels and the max loads indicated in the programme
section. Empty pockets. Make sure garments do not get caught
between the door and/or the door lter.
2. Close the door.
3. Press the button On/O.
4. Select the programme according to the laundry type.
5. Select the options, if necessary.
6. To start the cycle, press the Start/Pause button.
7. At the end of the drying cycle, a buzzer will beep. An indicator on
the control panel signals the end of the cycle. Pull the load out
immediately to prevent the formation of creases on laundry
8. Turn the machine o by pressing the button On/O, open the
door and pull clothing out. If the machine is not switched o
manually, after about a quarter of an hour from the cycle end, the
appliance turns o automatically to save energy.
If this last stage is not carried out immediately, some machines
and/or some programmes/options are equipped with Crease Care
system. For some hours, after the end of drying, the drum rotates
at regular intervals to prevent the formation of creases. In case of
power failure, it is necessary to press the button Start/Pause to
restart the cycle.
OPENING OF THE DOOR DURING THE CYCLE
During operation, it is possible to open the door. After having
closed it, press the button Start/Pause again to restart the dryer.
PROGRAMS
Eco cotton kg Max*
Standard cotton programme, suitable to dry normally wet cotton
laundry. Most ecient programme in terms of energy consumption
for drying cotton laundry. The values on the Energy Label are based on
this programme.
Mixed kg 4
This programme is ideal for drying cotton and synthetic fabrics
together.
Bed linen Kg Max*
This programme is intended for drying cotton sheets.
Shirts kg 3
This is a programme for Shirts made from cotton or cotton
blend/synthetics.
Sport kg 4
For drying sports garments made of synthetics or cotton.
Duvet
Programme intended to dry bulky garments, as single duvet.
Jeans kg 3
For drying cotton jeans-wear and garments made of robust
cotton, like denim, such as trousers and jackets.
Easy ironing
This cycle allows to extend the bres of garments thus making
ironing and folding easier. Do not use in case of garments that are
still wet. Suitable for small loads of cotton textiles or cotton blends.
Refresh
A short programme suitable for refreshing bres and garments by
means of fresh air. Do not use with garments that are still wet. It can be
used on with any load size but is more eective with small loads. The
cycle duration is about 20 minutes.
*MAX LOAD 8 Kg (Dry load)
CARE LABEL
Always check the care labels, especially when placing garments in
the tumble dryer for the rst time. Below are the most commonly
used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
Page 2
h
The duration of these programs will depend on the size of the
load, types of textiles, the spin speed used in your washer and
any extra options selected. In machines equipped with display,
the duration of the cycles is shown on the control panel. The
remaining time is constantly checked and adjusted during the
drying cycle to show the best possible estimate.
Rapid 30' kg 0,5
Ideal for drying cotton garments spun at high speed in the
washing machine.
Coloured kg Max*
Programme for gentle drying suitable for coloured garments.
Silk kg 0,5
Gentle drying of silk garments.
Wool kg 1
Programme for drying wool clothing. It is advisable to turn
the garments inside out before drying. Leave to dry naturally the
heaviest edges that are still damp.
Delicates kg 2
For drying delicate laundry which needs gentle treatment.
Synthetics kg 4
For drying laundry made of synthetic bres.
OPTIONS
After selecting the programme, the various options can be
set, if necessary.
Dryness level
Press the related button several times to obtain a dierent
level of residual moisture on garments. An indicator signals the
level being selected.
Iron dry: a very delicate ironing. Suitable for making ironing of
garments easier immediately after the end of the cycle.
Hanger dry: a level intended for delicate garments ready to
be hanged.
Cupboard dry: the garments are ready to be folded and put
away.
Extra dry: used for garments to be worn at the end of the
cycle.
Timed drying
This option allows to set the drying time. Press the
corresponding button to set the required time for drying. An
indicator on the control panel signals the time being selected.
Start delay
This option allows you to set the delay of the cycle start. Press
the corresponding button several times to obtain the required
delay. After having reached the max. settable time, the option is
reset by pressing the button again. An indicator on the control
panel signals the time being selected. After having pressed the
button Start/Pause, the machine signals the remaining time
for the cycle start. In case of door opening, after closing, it is
necessary to press the button Start/Pause.
Rapid
Enables quicker drying.
Fresh care+
If garments are left inside the drum after the end of the
cycle, they are subject to bacterial proliferation. This option allows
to prevent this proliferation by controlling the temperature and
the rotation of the drum. This treatment has a max. duration of 6
hours after the end of the programme set. This option remains in
memory if selected in the previous drying.
If this option is used together with the Start Delay, a crease
treatment (a periodic rotation of the drum) is added in the Start
Delay phase.
Key lock
This option makes all machine controls inaccesible, except
the button On/O. When the machine is on: to activate the
option, keep the button pressed until the indicator goes on. To
disable the option, keep the button pressed until the indicator
goes o. This option remains in memory if selected in the previous
drying.
Mute
This option turns o all sounds of control panel. Only
warnings remain active.
• to activate the option, keep the button pressed until the
indicator goes on.
• to disable the option, keep the button pressed until the indicator
goes o.
Cycle end
This option activates a prolonged buzzer at the end of the
cycle. Enable it if you are not sure to hear the normal sound at the
end of the cycle. This option remains in memory if selected in the
previous drying.
OPTIONS BUTTONS
These buttons serves to personalise the selected programme
according to personal requirements. Not all options are available
for all programmes. Some options are incompatible with the
ones previously set. The buzzer and/or blinking indicators will
signal the incompatibility. If the option is available, the option
indicator will stay on. Some options may be kept in the memory
of the programme if selected in the previous drying.
Page 3
EN
Quick guide
CARE AND MANTENANCE
AB
1
4
2
3
CD
Unplug the dryer during the cleaning and maintenance
procedures.
Emptying the water tank after each cycle (see Fig. A).
Pull the container out of the dryer and and empty it into a
sink or other suitable drain, then place it back. Do not use the dryer
without having inserted the container back in place.
Cleaning the door lter after each cycle (see Fig. B).
Pull the lter out and clean it by removing the lint from the
lter surface under running water or using a vacuum cleaner. For
optimal performance, dry up all the lters before inserting them
back in place. Do not use the dryer without having reinserted the
lter in place.
Remove the door lter as described below:
1. Open the door and pull upwards.
2. Open the lter and remove lint from all its parts. Replace it
correc tly.
Ensure it is completely inserted ush with the dryer seal.
Cleaning the bottom lter when the relevant indicator
turns on (see Fig. C).
Pull the lter out and remove the lint from its surface by washing
it under runing water or by using a vacuum cleaner.
However, it is advisable to clean this lter after each cycle to
optimise drying performance. Do not use the dryer without
having inserted the lter in place rst.
Remove the bottom lter and the condenser as described
below:
1. Open the bottom door.
2. Take the handle and pull the bottom lter out.
3. Open the rear side of the lter and remove the lint from the
inner surface of the mesh.
4. Clean the bottom lter chamber (there might be residual
water: this is normal).
5a. Approximately every 3 months, clean the condensing unit
(gure D) situated behind the bottom lter.
5b. Lower the levers situated on the sides of the condenser. After
having removed the condenser, clean it under running water.
5c. Place the condenser back in place and lift the levers.
6. Close the rear side of the bottom lter and place it back by
checking it is perfectly integrated in place.
7. Lower the lter handle and close the bottom door.
8. Make sure the air intake is free.
The lters are essential parts for drying. They are intended
to collect the lint formed during drying process. In case
of clogged lters, the air ow inside the dryer would be
seriously aected: the drying times would be longer, the
energy consumption would increase and the dryer could be
damaged. If these procedures are not carried out properly,
the dryer may not start.
TRANSPORT AND HANDLING
Never lift the dryer by holding it at the worktop.
1. Unplug the dryer.
2. Make sure that door and water tank are properly closed.
3. If the drain hose is connected to your sewage system, x the
drain hose on the rear of the dryer again (see Installation Guide).
Power consumption
o-mode (Po) - Watts 0.50
left-on mode (Pl) - Watts 1.00
Programs Kg kWh Minutes
Eco Cotton *
Eco Cotton
Synthetics 4 1.83 90
*Test programme according to AS/NZS 2442.2 standard. Tested with
maximum rated load capacity and dryness level Extra Dry.
8 4.74 130
4 2.59 80
PRODUCT DESCRIPTION
1. Water Tank
2. Air Intake
3. Bottom lter and condenser
4. Door lter
Page 4
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance,
please register your product on
www.whirlpool.eu/register
EN
Quick guide
Before using the appliance carefully read the Safety Instructions.
Before using the appliance carefully read the Safety Instructions.
Malfunction
Possible cause
Solution
The plug is not inserted into the socket.
Insert the plug into the socket.
The door is open.
Close the door.
set or switch the machine o to reset it. Refer to the section Options.
the program.
out.
described.
The programme, the time and/or the drying
amount of load inserted into the dryer.
Carry out a washing cycle with higher spin speed to remove as much
water as possible.
programme.
did not end.
to restart the cycle.
Lights on or ashing
Door lter
lter*
Clean the door lter and the bottom one and check whether air
damages.
turns o .
For instance: F3 and E2
W11385486
TROUBLESHOOTING
Before contacting the Service Centre, refer to the table below. Often the malfunctions are minor and can be solved in few minutes
The tumble
dryer does not
The plug is faulty.
Try to plug another appliance in the same socket. Do not use
connecting electrical devices to the socket, as adapters or extensions
turn on.
A power failure occurred. Await the reactivation of the power supply.
For machines equipped with this function: await the end of the delay
Press the button Start/Pause.
Refer to the option section and, if the Key Lock is present, disable it.
Switching the machine o is not enough to disable this option.
Refer to the section Care & Maintenance and perform the operations
Refer to the section programmes and options to nd the programme
and the options most suitable for the type of load.
Refer to the programme section to check the max. load for each
In case of power failure, it is necessary to press the button Start/Pause
The tumble
dryer does not
start
The drying
times are very
long
The programme
A time delay for the cycle start was set.
The button Start/Pause was not pressed to start
The function Key Lock was enabled (in case of
machines equipped with this option).
An appropriate maintenance was not carried
level set are not suitable for the type and the
The garments are too wet.
The dryer may be overloaded.
A power failure occurred might have occurred.
Water tank The water tank is full. Emtpy the water tank. Refer to the section Care & Maintenance.
and/or bottom
Failure of the air ow necessary for machine
operation.
intake is free. Carrying out these operations improperly may cause
Bottom lter* The bottom lter requires cleaning. Clean the bottom lter. Refer to section Care & Maintanence.
Disable the DEMO mode. The following actions must be carried out
DEMO
The cycle lasts
few minutes.
The dryer is in DEMO mode. The DEMO
indicator is on.
in sequence, without breaks. Switch the machine on and then switch
it o again. Press the Start/Pause button until the buzzer is heard.
Switch the machine on again. The “DEMO” indicator ashes and then
Switch the dryer o and unplug it. Open the door immediately and
The presence
of wrench
symbol signals a
malfunction.
The machine sensors detected a failure.
pull laundry out, to allow the heat to dissipate. Wait for about 15
minutes. Reconnect the dryer to the power supply, load the laundry
and restart the drying cycle. If the problem still occurs, contact
the After-Sales Service Centre and communicate the letters and
digits ashing on the display.
*Note: some models are self-cleaning and not equipped with bottom lter. Please refer to the section Care & Maintenance.
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
• Visiting our website - docs.whirlpool.eu
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product’s identi cation plate.
08/2019
xxxxxxxxxxxx
xxxxxxxxxxxx
xxxx
xxxx
Loading...