Whirlpool CA2762XYW0 Installation Guide

IMPORTANT:

Part No, 3360618

Read and save

these instructions

IMPORTANT:
Installer: Leave Installation Instructions

with the owner.

Owner: Keep Installation Instructions for

future reference.

Save Installation Instructions for local

electrical inspector's use.

www.whirlpool.com

COMMERCIAL

IC

120-volt, 60-Hz Models

®

COMMERCIAL
LAUNDRY
PRODUCTS

@

Before you start._

Your safety and the safety of

others is very important.

Wehaveprovided many important
safety messagesin this manualandon

your appliance.Always readand obey all
safety messages.

This is the safety alert
symbol. This symbol alerts

__ you to hazardsthat cankill or
hurt you andothers. All safety
messageswill be preceded by the safety
alert symbol and the word "DANGER"or

"WARNING".Thesewords mean:

Youwiii be killed or seriouslyinjuredif
youdon'tfollow instructions.

Youcanbe killed or seriously injured if
youdon'tfollow instructions.

All safety messageswill identify the hazard,
tellyou how to reducethe chance of injury,
andtell you what can happenif the

instructions arenot followed.

Do Not storeor operate washer below
32°F(some water may remain in

washer).
See Use& Care Guide for

"Winterizing" information.

Check location where washer
will be installed, Proper

installation is your responsibility,
Make sure you have everything
necessary for correct installation,

Untape and
open washer

lid, Remove
packages

and hoses
from washer,

No. T20 Torx

screws

On coin-operated washers, front
access to the pump area isavailable
by removing the two, No, T20 Torx
screws and then removing the front
panel, Non-coin-operated washers do
not have a removable front panel,
The cabinet and top assembly must
be removed by removing clips under
console on the non-coin-operated

washer,

PAGE 2

Single washer
installations require 12

inch minimum risers to
provide an air cushion

and prevent noise and
damage to valves,

Non-coin-operated washers are
equipped with a console, push to start

timer, selector switches and indicator
lights (net pictured),

A floor drain should be provided
under the bulkhead, Prefabricated

bulkheads with electrical outlets,
water supply lines and drain facilities

should be used only where local
codes permit,

Grounded
electrical outlet

isrequired, See
Electrical

requirements,

Level floor:

Maximum

slope under

washer-- ] inch,

Hot and cold wafer faucets must be
within 4 feet of the back of the washer

and provide water pressure ] 0-1 O0 PSI,
A pressure reduction valve should be
used in the supply line where inlet
pressure entering the building
exceeds ] O0 PSIto prevent damage
to the washer mixing valve,

Wafer heater: Set to deliver

140°F to 160°F water to the

washer,

Standpipe drain system: Needs a two-
inch minimum carry-away capacity
of 17gallons per minute, Top of
standpipe must be at least 34 inches
high and no higher than 72 inches

from bottom of washer,

Support: Floor must be sturdy enough
to support loaded washer weight of
315 pounds,

Important: Observe all governing
codes and ordinances.

Tools needed for
installation:

Electrical requirements

3-prong type outlet ------_--J]lllllt_l
ground

3-prong ground-

level

Cii

utility

knife

fiat-blade
screwdriver

)liers

Parts supplied for
installation:

Electrical Shock Hazard

Plug into a grounded 3-prong outlet.
Do not remove ground prong.
Do not use an adapter.

Do not use an extension cord.
Failure to follow these instructions

can result in death, fire, or electrical
shock.

If codes permit and a separate ground
wire is used, it is recommended that a

qualified electrician determine that
the ground path is adequate.

Do Not ground to a gas pipe.
Check with a qualified electrician if

you are not sure the washer is properly
grounded.

Do Not have a fuse in the neutral or
ground circuit.

A 120-volt, 60-Hz, AC-only, 15- or
20-ampere fused electrical supply is
required, (Time-delay fuse or circuit
breaker isrecommended.) It is
recommended that a separate circuit
serving only this appliance be provided,

plug

power supply
cord

Figure ]

Now start...

With washer in laundry area.

Excessive Weight Hazard

Use two or more people to move

and install washer.

Failure to do so can result in back

or other injury.

shipping

Remove parts from packages. Check
that all parts were included,

I hose clamp

2 inlet hoses
4 flat water hose washers
2 front-leveling legs with nuts

I drain hose

PAGE 3

Recommended
ground method

For your personal safety, this appliance
must be grounded. This appliance is
equipped with a power supply cord
having 3-prong ground plug. To
minimize possible shock hazard, the
cord must be plugged into a mating
3-prong ground-type outlet, grounded

in accordance with local codes and
ordinances. See Figure 1. If a mating

outlet isnot available, it is the personal
responsibility and obligation of the
customer to have a properly grounded
3-prong outlet installed by a qualified

electrician.
WARNING - Improper connection of

the equipment-grounding conductor
can result in a risk of electric shock.

Check with a qualified electrician or
serviceman if you are in doubt as to
whether the appliance is properly
grounded, Do not modify the plug
provided with the appliance - if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.

Remove tape that covers

[] shipping strap, Pull to
completely remove the shipping
strap with 2 cotterpins from the inside

of the washer,

Pull firmly to remove the
end of shipping strap from
the back of the washer, The shipping
strap plug must be completely

removed from the washer for the
self-leveling legs to be released,

Save the shipping strap for use in
Step 6.