Whirlpool C 900, C 847, C 844 BR, C 848 BL, C 859 User Manual

...

INSTRUCTIONS FOR USE

BEFORE USING THE DISHWASHER/ CONNECTIONS

ELECTRICAL CONNECTION PRECAUTIONS AND GENERAL

RECOMMENDATIONS HOW TO FILL THE SALT CONTAINER HOW TO FILL THE RINSE AID DISPENSER HOW TO FILL THE DETERGENT DISPENSER CARE AND MAINTENANCE

BEFORE USING THE DISHWASHER/ CONNECTIONS

1. Removing the packaging and controls:

After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly . If in doubt, contact a qualified technician or your local retailer.

Keep the packaging materials (plastic bags,

•

polystyrene parts, etc.) out of reach of children, as they are potentially dangerous.

This dishwasher has been factory tested to ensure

•

it functions correctly. Such testing may leave slight water marks that will disappear with the first wash.

2. Water and electrical connections:

All water and electrical connections must be carried out by a qualified technician in compliance with the manufacturer's instructions (refer to the enclosed installation booklet) and current local safety regulations. The appliance must only be used in the household for the prescribed uses.

Do not use the dishwasher if it has been damaged in transit. Consult your local retailer or our AfterSales Service.

(Refer to the separate installation instructions booklet)

3. Water inlet and drain:

Observe any special regulations issued by your local

•

Water Board. Water supply pressure: 0.3 - 10 bar.

Make sure the inlet and drain hoses are kink-free

•

and are not crushed. If the hose length is not sufficient, please contact

•

your local dealer or our After-Sales Service. The inlet hose must be securely clamped to the

•

water tap to prevent leaks. The inlet water temperature varies according to

•

the model installed. Inlet hose marked “25°C Max”: maximum temperature 25°C. All other models: maximum temperature 60°C. When installing the appliance, make sure the drain

•

water discharges correctly (if necessary, remove the wire gauze from the sink siphon). Fix the drain hose to the spigot with a clamp to

•

prevent it from coming off during operation. For appliances with water-stop system only: If the water connections are made correctly, the waterstop system safeguards your home against damage caused by flooding.

4. Electrical connection:

Closely adhere to local Electricity Board

•

regulations. Voltage information is shown on the rating plate

•

mounted inside the door on the right hand side. The appliance must be earthed as prescribed by law.

•

Do not use extension leads or multiple adapters.

•

Before carrying out maintenance, disconnect the

•

mains plug. If necessary, the power cable may be replaced with

•

one the same obtained from our After-Sales Service. The power cable must only be replaced by a qualified technician.

Warning for models provided with LCD display:

The mains plug must be positioned in an easily accessible place.

•For Austria:

a fault current switch, this must be sensitive to the pulsating current.

EC Declaration of conformity

This appliance has been designed, constructed and distributed in compliance with the safety requirements of EC Directives: 73/23/EEC

•

89/336/EEC

•

93/68/EEC

•

Load capacity:

12 place settings.

if the apparatus is series connected to

ELECTRICAL CONNECTION

1) For Great Britain only Warning - this appliance must be earthed Fuse replacement

If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A.S.T.A. approved fuse to BS 1362 type and proceed as follows:

Remove the fuse cover (A) and fuse (B).

Fit replacement 13A fuse into fuse cover.

Refit both into plug.

3. Important:

The fuse cover must be refitted when changing a fuse and if the fuse cover is lost the plug must not be used until a correct replacement is fitted.

Correct replacement are identified by the colour insert or the colour embossed in words on the base of the plug. Replacement fuse covers are available from your local electrical store.

2) For the Republic of Ireland only

The information given in respect of Great Britain will frequently apply, but a third type of plug and socket is also used, the 2-pin, side earth type.

3) Socket outlet / plug (valid for both countries)

If the fitted plug is not suitable for your socket outlet, please contact Whirlpool Service for further instruction. Please do not attempt to change plug yourself. This procedure needs to be carried out by a qualified Whirlpool technician in compliance with the manufactures instructions and current standard safety regulations.

+ 6 hidden pages