Whirlpool C 2010 BL PROGRAM CHART
r
Quick reference guide
PROGRAMME
AND DELAY
SELECTOR
KNOB
(see at right for
options description
and Table of
programmes below)
P
1
2
3
4
5
1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions
(without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible
with sensor programmes as a result of the appliance’s automatic calibration system.
2) Reference programme for energy label in complian ce with EN 50242 regul ations. - No te for Testing Institutes: fo
detailed information on the EN/Standard loading comparison test and other tests, contact the following address:
“nk_customer@whirlpool.com”.
START BUTTON
The indicator lights up during operation, flashes when a fault occurs, and goes off at the
end of the programme.
START BUTTON RESET FUNCTION:
Press this button for at least 2 seconds; the selected programme and options will be
cancelled. Main failure displays (repeated flashing of the START indicator lamp) can be
cancelled by RESETTING. Detailed instructions are given in chapter “What to do if...”.
Table of programmes
50°C
Available
options
Loading instructions
Crockery to be washed
Delay
later.
Light soiling, for example
Delay
glasses and cups.
Lightly soiled crockery , with
Delay
no dried-on food. * Use of
tablets not recommended.
Delay Normally soiled crockery. X 12.0 1.05 150
Recommended programme
for heavily soiled crockery,
Delay
especially suitable for pots
and pans.
Programmes
Pre-Wash cold
Glasses 40°C
Quickwash 45°C
2)
Eco
Intensive 70°C
Consumption
Deter-
gent
Litres kWh
— 4.0 0.03 14
X 10.0 0.85 100
X * 11.0 0.80 30
X 14.0 1.55 155
ON/OFF
BUTTON
Minutes
BEFORE USING THE APPLIANCE FOR THE
FIRST TIME CAREFULLY READ THIS QUICK
REFERENCE GUIDE AND THE ASSEMBLY
INSTRUCTIONS! THE GUARANTEE IS NOT
APPLICABLE IF FAULTS ARE CAUSED BY
INCORRECT USE OF THE APPLIANCE.
Options and display description
Programme settings
without start delay
1
1)
2
3
Switch on the appliance
- press the ON/OFF button.
OK/Start lamp flashes.
Set the desired start delay (3-6-9h). The
selected start delay lamp (3-6-9h)
Press the OK/Start button for
confirmation. After that the OK/Start
lamp switches off and the selected start
delay lamp lights up.
If you wish another time setting, press
OK/Start button again.
Turn the programme knob to your
desired programme position.
The OK/Start lamp flashes.
Press the OK/Start button for
After that the OK/Start lamp lights up.
The dishwasher starts immediately or
For a Reset, press the OK/Start button at
Indication:
described settings have to be selected
within 30 seconds, otherwise no settings
confirmation.
after the start delay selected.
a minimum of 2 seconds.
All settings are cancelled.
In the selection mode, all
will be saved.
flashes.
Start delay and
programme settings
5019 696 01536C 2010
1
2
3
4
5
Chart
GB
-1-
How to set detergent type: powder/gel/tablet (if option is available)
First time use
In order to always ensure the best cleaning
results, you NEED to set:
DETERGENT type and WATER HARDNESS.
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
1.
Select 3rd programme
(see Table of programmes
- page 1)
2.
Press START button
for 7 seconds
3a.
For models without “detergent type” option, the salt and rinse aid indicators will be lit when tablets are used.
How to set water hardness
Switch on the appliance
* only before the first wash or if
the water hardness has been
changed
1.
Ask your water supply company what
water hardness
the
French
degrees °fH
0 - 9 Soft 1 1x
10 - 18 Medium 2 2x
19 - 27 Average 3 3x
28 - 37 Medium-hard 4 4x
38 - 50 Hard 5 5x
51 - 63 Very hard 6 6x
64 - 107 Extremely hard 7 7x
is...
Water
hardness
- Select the 2nd programme “P2” - consult the table of programmes.
- Press the START button for at least 5 seconds until the START indicator lamp flashes.
- The water hardness setting is shown on the display (if present) or the START button flashes.
- With each successive touch of the START button the setting increases and when it reaches 7 it returns to 1 again.
- The appliance must be switched off to memorise the new setting.
2.
...enter this value on your dishwasher
Dishwasher with
display: insert value
in the display
Check your
detergent type...
Detergent
types
Powder or gel
(factory setting)
Tablet 2 in 1
Tablet 3 in 1
Tablet All in 1
Dishwasher without
display: count
START button led
flashes
3b.
...and set it on your dishwasher
using the START button
(as per table below)
Dishwasher models
model without
display
3h 6h 9h
Gel or Powder
(rinse aid and salt)
(see “Daily check”)
model with display
Suggestions for detergent use
go to step 1
4.
Remember to use salt and rinse
aid when needed (as indicated
below)
no symbol add salt add rinse aid
add salt
salt
Tablets
rinse aid
rinse aid
Water hardness level is factory set for
medium hard water (a number “4” is
shown on the display or the START
indicator lamp flashes 4 times).
if extra salt is
needed go to step 1
(see “Daily check”)
Even if you use tablets which include salt,
you must still add salt since such
detergents are not effective enough at
softening hard water.
5.
Switch off and switch on
again to save setting
GB
-2-
1
Filling the salt reservoir -
Dissolve limescale (not necessary if water hardness level is set to “soft”!)
Daily check
The salt level indicator lamp may remain lit for the duration of several wash cycles. If the
water hardness level falls within category (soft),
Adding rinse aid
(not necessary when you use tablets). How to adjust the rinse aid dosage regulator
2
Rinse aid indicator (depending on model)
Only use rinse aids recommended for use in domestic dishwashers.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly d ry : incr e a s e the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid
setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programmes. In the case of shorter programmes, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend
to form excess suds.
Adding detergent -
3
S
E
L
Visual indicator
(depending
on model).
Unscrew cap.
Visual
indicator
If required,
open the cover
B (press right
button).
no
salt is required.
The indicator lamp on the control panel lights up when RINSE AID NEEDS TO BE
ADDED.
Immediately
Fill the salt
reservoir with
water before the
first wash only.
S
E
L
Salt indicator
(depending on
the model)
Add rinse aid
to the max.
line ~150 ml
wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.
The indicator lamp on the control panel lights
up when SALT NEEDS TO BE ADDED.
Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Tablet / gel / powder
Use only one tablet per one
Open the cover A
(press left button).
Only fill the
detergent dispenser
prior to starting a
wash programme.
cycle, only placed in detergent
dispenser.
All types of tablets can be
used, but for 2 in 1 type
adding of salt is mandatory.
S
Add salt
(never add
detergent!).
min. 1.5 kg
S
max. 2 kg
E
L
orange: OK. clear: NEEDS TO BE ADDED
The rinse aid dosage can be adjusted to the
detergent used. The lower the setting,
the less rinse aid is dispensed
(factory setting: position 4).
Press the button to open the cover B. Using a
coin or similar object, turn the arrow to the
desired setting. After adjusting the rinse aid
setting, shut the cover again.
dark: OK. clear: NEEDS TO BE ADDED
By pressing
dedicated ribs
shut the cover.
E
L
Visual indicator (depending
on model). Screw on the cap.
Salt residues around cap
need to be removed.
Daily use
GB
-3-
Loading...