Whirlpool C 1010 IS, C 1010 NB PROGRAM CHART

Quick reference guide

PROGRAMME AND DELAY SELECTOR KNOB

(see at right for options description and table of programmes below)

1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of the appliance’s automatic calibration system.

2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

(**) It is recommended to check the cleanness of the filter and clean it if necessary, to assure the correct functioning of the washing

programme.

START BUTTON

The indicator lights up during operation, flashes when a fault occurs, and goes off at the end of the programme.

START BUTTON RESET FUNCTION:

Press this button for at least 2 seconds; the selected programme and options will be cancelled. Main failure displays (repeated flashing of the ST ART indicator lamp) can be cancelled by RESETTING. Detailed instructions are given in chapter “What to do if...”.

Table of programmes

Programmes

Eco Green 50°C

Pre-Wash cold

Quickwash 40°C

Eco

Intensive 70°C

Available

options

Delay

Delay Crockery to be washed later. — 5.0 0.02 10

Delay

Delay Normally soiled crockery. X 15.0 1.05 150

50°C

Delay

Loading instructions Litres kWh

Usual dirty dishes. Not for full load, for minimum consumptions

(**)

Lightly soiled crockery, with no dried-on food.

not recommended.

Recommended programme for heavily soiled crockery , especially suitable for pots and pans.

* Use of tablets

Detergent

X 13.0 0.90 126

X*13.0 0.70 30

X 17.0 1.65 145

ON/OFF

BUTTON

Consumption

Minutes

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE INSTALLATION INSTRUCTIONS! THE GUARANTEE IS NOT APPLICABLE IF FAULTS ARE CAUSED BY INCORRECT USE OF THE APPLIANCE.

Options and display description

Programme settings without start delay

Switch on the appliance

- press the ON/OFF button. OK/Start lamp flashes.

Set the desired start delay (3-6-9h). The

selected start delay lamp (3-6-9h)

Press the OK/Start button for

confirmation. After that the OK/Start

lamp switches off and the selected start

If you wish another time setting, press

Turn the programme knob to your

desired programme position.

Press the OK/Start button for

After that the OK/Start lamp lights up.

The dishwasher starts immediately or

after the start delay selected.

For a Reset, press the OK/Start button at

Indication:

described settings have to be selected

within 30 seconds, otherwise no settings

flashes.

delay lamp lights up.

OK/Start button again.

The OK/Start lamp flashes.

confirmation.

a minimum of 2 seconds. All settings are cancelled.

In the selection mode, all

will be saved.

Start delay and programme settings

5019 696 01532C1010

Chart

-1-

How to set detergent type: powder/gel/tablet (if option is available)

First time use

In order to always ensure the best cleaning results, you NEED to set: DETERGENT type and WATER HARDNESS.

1- salt reservoir 2- rinse aid dispenser 3- detergent dispenser 4- racks system 5,6,7,8- available functions on the

panel 9- filters 10- spray arms

Select 3rd programme (see Table of programmes

- page 1)

Press START button for 7 seconds

For models without “detergent type” option, the salt and rinse aid indicators will be lit when tablets are used.

How to set water hardness

before the first wash

only

water hardness has been changed

Ask your water supply company what the

hardness

is...

French

degrees °fH

0 - 9 Soft 1 1x go to step 2 go to step 3 10 - 18 Medium 2 2x 19 - 27 Average 3 3x 28 - 37 Medium-hard 4 4x 38 - 50 Hard 5 5x 51 - 63 Very hard 6 6x

64 - 107 Extremely hard 7 7x

water

Water

hardness

or if the

...enter this value on your dishwasher

Dishwasher with

display: insert value

in the display

3a.

Check your detergent type...

Detergent

types

Powder or gel

(factory setting)

Tablet 2 in 1

Tablet 3 in 1

Tablet All in 1

3b.

...and set it on your dishwasher

using the START button

(as per table below)

Dishwasher models

model without

display

3h 6h 9h

model with display

Remember to use salt and rinse aid when needed (as indicated below)

no symbol add salt add rinse aid

add salt

salt

rinse aid

Switch off and switch on again to save setting

Switch on the appliance

- Select the 2nd programme “P2” - consult the table in the Programme Chart.

- Press the START button for at least 5 seconds until the START indicator lamp flashes.

- The water hardness setting is shown on the display (if present) or the START button flashes.

- With each successive touch of the START button the setting increases and when it reaches 7 it returns to 1 again.

- The appliance must be switched off to memorise the new setting.

Suggestions for detergent use

Dishwasher without

display: count START

button led flashes

Gel or Powder

(rinse aid and salt)

Tablets

Water hardness level is factory set for medium hard water (a number “4” is shown on the display or the START indicator lamp flashes 4 times).

go to step 3

Even if you use tablets which include salt,

go to step 1

if extra salt is needed go

to step 1 and then 3

you must still add salt since such detergents are not effective enough at softening hard water.

-2-

Filling the salt reservoir -

Dissolve limescale (not necessary if water hardness level is set to “soft”!)

Daily check

The salt level indicator lamp may remain lit for the duration of several wash cycles. If the water hardness level falls within category (soft), no salt is required.

Adding rinse aid

(not necessary when you use tablets). How to adjust the rinse aid dosage regulator

Rinse aid

indicator (depending on model)

Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This p revents the formation of excess suds which can cause a fault function of the appliance. If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly d ry : incr e a s e the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid

setting will not improve the situation. Detergents with rinse aid incorporated may be effective only with longer programmes. In the case of shorter programmes, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend

to form excess suds.

Adding detergent -

Visual indicator (depending on model). Unscrew cap.

Visual indicator B

If required, open the cover (press lever).

The indicator lamp on the control panel lights up when RINSE AID NEEDS TO BE ADDED.

Fill the salt reservoir with water before the first wash only.

Salt indicator

(depending on

the model)

Add rinse aid to max. line ~100 ml

The indicator lamp on the control panel

lights up when SALT NEEDS TO BE

ADDED.

Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations.

Tablet / gel / powder

Add salt

(never add detergent!). min. 1.5 kg max. 2 kg

orange: OK. clear: NEEDS TO BE ADDED

The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the lever to open the cover. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.

dark: OK. clear: NEEDS TO BE ADDED

Visual indicator (depending on model). Screw on the cap. Salt residues around cap need to be removed.

Daily use

Open the cover A (press lever).

Only fill the detergent dispenser prior to starting a wash programme.

Use only one tablet per cycle, placed in the detergent dispenser.

-3-

+ 5 hidden pages