Whirlpool AWV 516/IG, AWV 616, AWO 626 INSTRUCTION FOR USE

GB
PROGRAMME CHART
A. “Door open” indication
This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately, e.g.:
B. “Service” indication C. “
Water tap closed
” indication
D. “Clean pump” indication
Care
Programme
Cotton
60 - 95°C
Cotton
40°C
Synthetics
30 - 40 - 60°C
Delicates
30 - 40°C
Daily load
40°C
Quick wash
30°C
Wool
Cold - 40°C
Handwash
30 - 40°C
Rinse & Spin
Spin Centrifugeren / Essorage
Gentle Spin
Drain Afpompen / Vidange
: option / Yes : dosing required
1)
For improved garment care spin speed is restricted in these programmes.
Katoen/ Coton
60 - 95°C
Katoen/ Coton
40°C
Synthetisch
Synthétiques
30 - 40 - 60°C
Fijne was/ Délicat
30 - 40°C
Gemengde was
40°C
Snelwas Chrono
30°C
Wol/ Laine
Koud/Froid - 40°C
Handwas
Lavage main
30 - 40°C
Spoelen+Centrifugeren
Rinçage + Essorage
Kort centrifugeren
Essorage doux
Labels
Max. Load
kg
Normally to heavily soiled bed linen, table linen and underwear,
6.0 towels, shirts etc. made of cotton and linen.
With heavily soiled laundry the additional “Prewash” option can be
5.0
additionaly selected.
Normally soiled blouses, shirts, overalls etc. made of polyester
2.5 (Diolen, Trevira), polyamide (Perlon, Nylon) or blends with cotton.
1.5 Curtains and delicate clothing, dresses, skirts, shirts and blouses.
Shortly worn outer clothing made of cotton, polyester, polyamide
3.0 and blends with cotton.
Shortly worn outer clothing made of cotton, polyester, polyamide
3.0 and blends with cotton.
Only woollens with a felt-free finish, labelled with the woolmark and
1.0 identified as machine washable.
Textiles made of linen, silk, wool and viscose marked as
1.0 “handwashable”.
6.0 Same as the last rinse and the final spin in the “Cotton” programme.
In this programme spinning is intensive. Same as the spin cycle in the
6.0
“Cotton” programme.
In this programme spinning is gentle. Same as the spin cycle in the
1.0
“Wool” programme.
Drain only - no spinning. Alternative method of terminating programme after “Rinse hold”.
C
D
Type of wash / Notes
E. Programme selector
H
A
B
IJ
F. “Start/Pause” button G. Spin speed selector H. Programme sequence indicator and Start delay indicators I. “Reset” button J. “Start delay” button
E
F
Detergents and Additives Special options Max
Pre-
Main
Wash
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Softener
wash
G
Start
delay
Start-
selectie
Pre-
wash
Voor-
was
Eco Intensive
rinse
Whirlpool is a registered trademark of Whirlpool USA.
Rinse
hold
Variable
spin
Spin
Speed
rpm
Max.
1000
1000
Max.
Max.
1000
400
Max.
Max.
1000
1)
1)
1)
1)
1)
5019 301 01087
CONSUMPTION DATA
Temperature
Load
Water
Energy
Programme
(°C)
Cotton 95 6.0 59 * 1.90 2:00
Cotton with “Eco”** 60 6.0 49 1.02 2:20
Cotton 60 6.0 49 1.14 2:10
Cotton 40 5.0 56 0.70 2:00 Synthetics 60 2.5 50 * 0.80 1:35 Synthetics 40 2.5 46 0.50 1:20
Delicates 30 1.5 60 0.50
Daily load 40 3.0 41 0.50
Quick wash 30 3.0 41 0.40
Wool 40 1.0 60 0.50 Handwash 40 1.0 45 0.50 Handwash 30 1.0 45 0.40
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. * To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out. ** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE PROGRAMME
Add detergent as indicated on the front page and as described in the chapter “Detergent and Additives” in your Instructions for Use. Close the door and turn the programme selector to the desired programme and temperature. The indication lamp next to the “Start/Pause” button blinks and the indication lamp of the predefined spin speed lights up.
(kg)
(l)
(kWh)
“Intensive rinse” button
More water is added and rinse cycle is prolonged.
This option is particularly suitable for areas with
very soft water, washing baby linen and helps people with allergies.
“Rinse hold” button
The laundry remains in the last rinse water
without pregressing to the final spin cycle to avoid creasing and prevent colours from changing.
This option is particularly recommended for the programmes “Synthetics”, “Daily load” and
Approx. Programme
Duration
(hours : minutes)
0:41 1:00 0:30 0:46 0:41 0:37
“Delicates”.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the respective indication lamp lights up. When the combination of programme and additional option(s) is not possible, the indication lights switch off automatically. Unsuitable combinations of options are deselected automatically.
“Prewash” button
Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by approximately 15 min.
Do not use liquid detergent for the main wash when activating the “Prewash” option
.
“Eco” button
With a modified temperature profile and a slightly
It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
If you select “Rinse hold” do not leave items to soak for too long. Note: The programme stops to “Rinse hold” at the time the “Rinse hold” lights in the preogramme sequence indication is on. The indication lamp next to the “Start/Pause”
button flashes.
Terminate the “Rinse hold” option:
Press the “Start/Pause” button; the programme
will terminate automatically with the final spin cycle for the present wash programme.
If you do not wish to spin the clothes, turn the programme selector knob to the “Drain” programme and press the “Start/Pause”
button.
prolonged washing duration, the optimum combination of excellent washing result and even lower energy consumption is achieved.
“Variable spin” button
Every programme has a predefined spin speed.
Press the button to set another spin speed.
If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during the rinse. The water is drained out only.
START DELAY
The “Start Delay” allows to run the machine at the consumer’s convenience, for example at night when electricity is cheaper. Do not use liquid detergent when activating “Start delay” option.
• Select programme, temperature and options.
• Press the “Start Delay” button to select the delay time by 1, 3, 6, 9 or 12 hours.
• Press the “Start/Pause” button. The indication over to the “Start Delay” button lights up and goes off when the programme starts.
• Once having pressed the “Start/Pause” button, the countdown of the time delay begins. When the programme starts, the start delay indicator light goes off and is replaced by the programme sequence indication.
• After the “Start/Pause” button has been pressed, the number of hours preselected can be reduced by pressing again the “Start Delay” button.
To cancel the “Start Delay” ..before you press the “Start/Pause” button:
• Turn the programme selector to another position or press the “Reset” button.
..after having pressed the “Start/Pause” button:
• Press the “Reset” button for at least 3 seconds ­ the start delay indicator light goes out.
PROGRAMME START
Open the tap and press the “Start/Pause” button. The indication lamp next to the “Start/Pause” button lights up. The programme sequence indicator shows the current programme phase, running from left to right through Wash, Rinse, Spin/Drain. When the programme phase is finished, the corresponding indication goes out.
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp lights to show the the door can be opened. As long as a wash programme is running, the door remains locked and must on no account be forced open. In case you have an urgent need to open it during a running programme, refer to “Cancel (Reset) a running programme before the end”.
RED INDICATIONS
“Service”
Lighting up of the “Service” indication can be caused by a fault in an electrical component. Refer to the “Troubleshooting Guide” in your “Instructions for Use”; if the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open the water tap: if the indications still lights up, refer to the “Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain hose is kinked or the filter must be cleaned: in the latter case refer to the Instructions for Use (“Removing the Filter”).
PROGRAMME END
All the lights of the programme sequence indicator
are off, and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS AFTER PROGRAMME START
1. Press the “Start/Pause” button to pause the programme. The light flashes.
2. Select the new programme (with temperature), any options and another spin speed if you want.
3. Press the “Start/Pause”
button again. The new programme continues at the same position where the previous programme was interrupted. Do not add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME BEFORE THE END
The “Reset” button cancels a programme before the end.
Press the “Reset” button for at least 3 seconds. Any existing water is drained out before the door can be opened.
Whirlpool is a registered trademark of Whirlpool USA.
5019 301 01087
Loading...