Whirlpool AWO/D 6041 PROGRAM CHART

GB AWO/D 6041

A. “Door open” indication

This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately, e.g.:

B.“Service” indication

C.“Water tap closed” indication

D.“Clean pump” indication

PROGRAMME CHART

C A

D B G

H

E F

E.Programme selector

F.“Start/Pause” button

G.Programme sequence indicator

H.“Reset” button

							Type of wash/Notes	Max	Detergents and additives					Special options				Spin
								Load
Programme				Care					Pre-	Main	Softener			Half	No Spin			Speed
				Labels					wash	Wash				load
							- for temperature selection, respect the manufacturer’s recommendations on the care label
								kg										rpm
Cotton with prewash							Heavily soiled, long wearing and temperature stable textiles in cotton and linen (bed linen,	5.0	Yes	Yes								600
95 °C							table linen, underwear, shirts etc.).
Cotton							Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made of	5.0	—	Yes								600
40 - 60 - 95 °C							cotton and linen.
Synthetics with prewash							Heavily soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide	2.5	—	Yes								600
60 °C							(Perlon, Nylon) or blends with cotton.
Synthetics							Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide	2.5	—	Yes								600
30 - 40 - 60 °C							(Perlon, Nylon) or blends with cotton.
Delicates							Curtains and delicate clothing, dresses skirts, shirts and blouses.	1.5	—	Yes				—				600
30 °C
Quick wash							Shortly worn outer clothing made of cotton, polyester, polyamide and blends with cotton.	3.0	—	Yes				—				600
30 °C
Wool							Only woollens with a felt-free finish, labelled with the woolmark and identified as machine	1.0	—	Yes				—				600
Cold - 40 °C							washable.
Handwash							Textiles made of linen, silk, wool and viscose marked as “handwashable”.	1.0	—	Yes				—				400 1)
30 - 40 °C
Rinse & Spin				—			Same as the last rinse and the final spin in the “Cotton” programme.	5.0	—	—								600
Spin				—			In this programme spinning is intensive. Same as the spin cycle in the “Cotton” programme.	5.0	—	—	—			—				600
Gentle Spin				—			In this programme spinning is gentle. Same as the spin cycle in the “Wool” programme.	1.0	—	—	—			—				600

Drain

—

Water is drained only without any spinning.

— — — — — — —

: optional / Yes : dosing required		Whirlpool is a registered trademark of Whirlpool USA
1)	For improved garment care, spin speed is restricted to 400 rpm in this programme.
		5019 301 10426

CONSUMPTION DATA

	Temperature	Load	Water	Energy	Approx. Programme
Programme					Duration
	(°C)	(kg)	(l)	(kWh)	(hours : minutes)
Cotton	95	5.0	49*	1.90	2:00
Cotton**	60	5.0	44	0.95	2:20
Cotton	40	5.0	44	0.60	2:00
Synthetics	60	2.5	50*	0.70	1:30
Synthetics	40	2.5	45	0.55	1:15
Delicates	30	1.5	50	0.50	0:45
Quick wash	30	3.0	40	0.40	0:30
Wool	40	1.0	55	0.60	0:45
Handwash	40	1.0	45	0.60	0:40
Handwash	30	1.0	45	0.50	0:40

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

*To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

**Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE PROGRAMME

Add detergent as indicated on the front page and as described in your Instructions for Use. Close the door and turn the programme selector to the desired programme and temperature. The indication lamp next to the “Start /Pause” button flashes.

SELECT ANY DESIRED OPTION

Push the button(s) of any option(s) desired - the respective indication lamp lights up.

When the combination of programme and additional option(s) is not possible, the indication lights switch off automatically. Unsuitable combinations of options are deselected automatically.

“Half load” button

•Reduces water consumption, above all during rinsing.

•Suitable for lightly soiled laundry and small loads (max. 3 kg).

“No Spin” button

•Especially for delicate garments to avoid wear and tear caused by the spin.

Note: with the “Cotton” and “Synthetics” programmes, a short spin cycle is provided in any case, even if the “No spin” option has been selected, in order to optimize rinsing results.

PROGRAMME START

Open the tap and press the “Start/Pause” button

. The indication lamp next to the “Start/Pause” button lights up. The programme sequence indicator shows the current programme phase, running from left to right through Wash, Rinse, Spin/ Drain.

When the programme phase is finished, the corresponding indication goes out.

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the lamp lights to show that the door can be opened. As long as a wash programme is running, the door remains locked and must on no account be forced open. In case you have an urgent need to open it during a running programme, refer to “Cancel (Reset) a running programme before the end”.

RED INDICATIONS

“Service”

Lighting up of the “Service” indication can be caused by a fault in an electrical component. Refer to the “Troubleshooting Guide” in your “Instructions for Use”; if the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open the water tap; if the indication still lights up, refer to the “Troubleshooting Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the drain hose is kinked or the filter must be cleaned; in the latter case refer to the Instructions for Use (“Removing the Filter”).

PROGRAMME END

•All the lights of the programme sequence

indicator are off, and the “Door open” indication lights up.

1.Turn the programme selector to the “Off/O” position.

2.Close the water tap.

3.Open the door and unload the machine.

4.Leave the door ajar to allow the drum to dry.

CHANGE PROGRAMME AND/OR OPTIONS AFTER PROGRAMME START

1.Press the “Start/Pause” button to pause the programme. The light flashes.

2.Select the new programme (with temperature), any options and another spin speed if you want.

3.Press the “Start/Pause” button again. The new programme continues at the same position where the previous programme was interrupted. Do not add detergent for this programme.

CANCEL (RESET) A RUNNING

PROGRAMME BEFORE THE END

The “Reset” button	cancels a programme
before the end.

•Press the “Reset” button for at least 3 seconds. Any existing water is drained out before the door can be opened.

Whirlpool is a registered trademark of Whirlpool USA

5019 301 10426