INSTRUCTIONS FOR USE
BEFORE USING THE WASHING MACHINE
FIRST WASH CYCLE
PRECAUTIONS AND GENERAL RECOMMENDATIONS
DESCRIPTION OF THE WASHING MACHINE
CHILD SAFETY
DETERGENTS AND ADDITIVES
WASHING PROGRAMME
REMOVING THE FILTER
DRAINING RESIDUAL WATER
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
TRANSPORT AND HANDLING
INSTALLATION
BEFORE USING THE WASHING MACHINE
1.Removing the packaging and check
After unpacking, make sure that the washing
•
machine is undamaged. If in doubt, do not use the
washing machine. Contact After-Sales Service or
your local retailer.
Keep the packaging materials (plastic bags,
•
polystyrene parts, etc.) out of reach of children, as
they are potentially dangerous.
2.Remove the transit bolts
The appliance is fitted with transit bolts to prevent
•
internal damage during transport.
washing machine you must remove the transit
(see “Installation/Remove the transit bolts”).
bolts
Before using the
3.Install the washing machine
Remove the protective foil from the control panel.
•
Move the machine without carrying it at the top.
•
Install the appliance on a solid and level floor
•
surface, preferably in a corner of the room.
Adjust the feet to ensure that the machine is stable
•
and level (see "Installation/Adjust the feet").
4.Water supply
Connect the water supply inlet hose in accordance
•
with regulations of your local water company (see
“Installation/Connect the water inlet hose”).
Water supply: cold water only
•
Tap: 3/4” threaded hose connection
•
Pressure: 100-1000 kPa (1-10 bar).
•
For Australia, New Zealand, Great Britain &
Ireland:
Water inlet: hot and cold fill.
•
The warm water inlet temperature must not exceed
60° C.
The hot water fitting is the same size and the same
•
pressure requirements apply as per cold water.
6.Electrical connections
Electrical connections must be carried out by a
•
qualified technician in compliance with the
manufacturer's instructions and current standard
safety regulations.
Voltage information, power consumption and
•
electrical protection data are supplied on the inside
of the appliance door.
The appliance must be connected to the mains
•
exclusively by means of a socket with an earth
connection in accordance with established
regulations. The appliance must be earthed by law.
The manufacturer declines all liability for damage to
property or injury to persons or animals deriving
either directly or indirectly from failure to observe
the directions.
Do not use extension leads or multi sockets.
•
Before any maintenance on the washing machine
•
disconnect it from the mains supply.
Access to the mains plug or to disconnection from
•
mains supply via a double-pole switch must be
ensured at all times following the installation.
Do not operate the washing machine if it has been
•
damaged during transport. Inform the After-Sales
Service.
Mains cable replacement is only to be carried out by
•
After-Sales Service.
The washing machine must only be used in the
•
household for the prescribed uses.
Minimum housing dimensions:
Width: 600 mm
Height with worktop: 825 mm
Height with UBS cover panel (optional): 600 mm
Depth: 600 mm
5.Drain hose
Connect the drain hose to the siphon or hook it over
•
the edge of a sink by means of the “U” bend (see
“Installation/Connect the water drain hose”).
If the washing machine is connected to a built-in
•
drainage system, ensure the latter is equipped with
a vent to avoid simultaneous loading and draining
of water (siphoning effect).
Home
Appliances
FIRST WASH CYCLE
We recommend the first wash cycle be made without laundry. This will remove any residual water used
in testing your washing machine.
Turn on the tap.
1.
Close the appliance door.
2.
Pour a small amount of detergent (about 30 ml) into the detergent dispenser .
3.
Select a short program (see programme chart).
4.
Press the
5.
“Start/Pause”
button.
PRECAUTIONS AND GENERAL RECOMMENDATIONS
1.Packing
The packing box may be fully recycled as confirmed
•
by the recycling symbol. Adhere to local
regulations when disposing of packaging material.
2. Energy saving tips
Achieve the best use of energy, water, detergent and
•
time by using the recommended maximum load size.
Do not exceed the detergent dosages indicated in the
•
manufacturer’s instructions.
The Eco Flap - a special system in the outlet - will
•
prevent detergent loss from the drum to avoid
detergent loss into the environment.
Use “Prewash” for heavily soiled laundry only! Save
•
detergent, time, water and energy consumption by not
selecting “Prewash” for slight to normally soiled
laundry.
Pretreat stains with stain remover or soak dried in
•
stains in water before washing to reduce the necessity
of a hot wash program.
Save energy by using a 60° C instead of a 90° C wash
•
programme or a 40° C instead of a 60° C wash
programme.
Save energy and time by selecting a high spin speed to
•
reduce the water content in laundry before using a
tumble dryer (for machines with adjustable spin
speed).
3.Disposing of packaging and old appliances
The washing machine is built from reusable
•
materials. The washing machine must be disposed of
in compliance with local waste disposal regulations.
Before scrapping, cut off the power cable so that the
•
washing machine cannot be connected to the
mains.
Remove detergent from compartment if you intend
•
scrapping your appliance.
4.Child safety
Children must not be allowed to play with the
•
washing machine.
5.General recommendations
When the appliance is not in use unplug it and turn
•
off the tap.
Before cleaning or carrying out maintenance, switch
•
off the washing machine and disconnect it from the
mains supply.
To clean the outside of the washing machine, use a
•
neutral detergent and a damp cloth.
Do not use abrasive detergents.
•
Do not attempt to force the door open.
•
If necessary, the power cable may be replaced with
•
an identical one obtained from our After-Sales
Service. The power cable must only be replaced by a
qualified technician.
6.EC Declaration of Conformity
This washing machine has been designed,
•
constructed and distributed in compliance with the
safety requirements of EC Directives:
93/68/EC.
DESCRIPTION OF THE WASHING MACHINE
Worktop
1.
Control panel
2.
Detergent dispenser
3.
After-Sales Service sticker (on
4.
the back side of the door)
Door
5.
Door handle
6.
To open the door press the
•
button on the inside of the
handle and pull
Close the door by pushing it
•
firmly (the lock will click into
place)
Child safety (inside door)
7.
Filter (behind cover)
8.
Plinth
9.
Adjustable feet
10.
3
9
10
1
2
4
5
6
7
8
CHILD SAFETY
To protect the appliance from improper use, turn the
plastic screw on the interior of the door using a coin or
the thick rounded plastic projection on the coloured
insert from the detergent dispenser:
Slot vertical: safety position, i.e. the door will not lock.
•
Slot horizontal: normal position, i.e. the door can be
•
locked again.
DETERGENTS AND ADDITIVES
B
Filling the detergents and additives
Pull out the detergent to its full extent.
1.
Filling the detergent:
2.
Programme with pre- and main wash.
•
Main wash programme without prewash.
•
When using liquid detergent, extract the coloured
insert from the detergent dispenser and put it
in the compartment.
The insert has a scale to make dosing easier.
Add fabric softeners and conditioners - no
•
further than the “Max” mark
(three chamber model “B”) or the“100 ml” mark
(four chamber model “A”).
Fill chlorine bleach only to the “Max” mark
•
(four chambers model “A”)
Stain remover
•
Water softener (water hardness class 4)
•
Starch (diluted in water). In this case select
•
the programme “Rinse and Spin”. After pouring
the starch fill about 1 litre of water into chamber.
Slide the detergent dispenser in until it clicks shut.
3.
Home
Appliances
A
B
Notes:
Keep detergents and additives in a dry place and out of reach of children.
•
If you use descaling agents, dyes or bleaches, make sure they are suitable for washing machine use. Descaler
•
could contain components that can attack parts of your washing machine.
Do not use solvents (turpentine, benzine, etc.).
•
Do not machine wash fabrics that have been treated with solvents or flammable liquids.
You can use liquid detergent in the “Prewash” phase for programmes with this option. In this case put only
•
powder detergents in the compartment for the main wash .
When using concentrated fabric softeners, add hot water in the softener dispenser up to “MAX” level mark.
•
To prevent dispensing problems when using highly concentrated liquid and powder detergents or
•
tablets, use the special detergent ball or bag supplied with the detergent and place it inside the drum.
WASHING PROGRAMME
Selecting the programme:
Plug in the appliance.
1.
Turn on the water supply tap.
2.
Set the
3.
4.
6.
Programme Selector
Depending on model the recommended temperature can be altered by pressing “+” or “-” button.
Select additional
5.
By pressing the button once more, this option can be turned off again.
Press the
The indicator light will come on and the programme duration is shown on the display (if available).
The indicator lamps show the sequence reached in the programme. After starting the programme, the
sequence indication runs from left to right through Wash, Rinse, Spin.
When the sequence of the programme is finished the corresponding lamp goes out.
“Start/Pause”
options
knob to the desired programme.
, if desired, pressing the corresponding button.The indicator lights up.
button.
Start delay
Select the programme and temperature, any additional options and the spin speed.
Pressing the “Start Delay” button the associated display comes on. Press the “Start Delay” button
repeatedly until the desired number of hours is reached. If the maximum number of hours is reached
for the delayed start, further pressing of the button starts the counter at zero again.
Press the “Start/Pause” button in order to start the programme, it will start after the selected time.
Correct the start delay
The start delay hours can be corrected even after the “Start/Pause” button has been pressed: press it
repeatedly until the desired number of hours is reached. Once the display has counted down the
selected programme is started and the related programme remaining time is displayed.
Cancel the start delay
Turn the programme selector and set it to the desired programme. The remaining time of the selected
programme is displayed and the “Start/Pause” button flashes. The programme can now be started
immediately by pressing this button.
N.B.
(if available)
With liquid detergent, a dosing aid placed directly in the drum should be used if a start delay has
been selected.
Door lock
The door locks automatically after the programme start until the end of the programme.
The “Door Free” indicator is on, before the starting and at the end of the programme.
If the programme selector is moved to the “” position or if the electricity supply is interrupted, then
after approximately one minute the door is released.
In this case do not open the door, because hot water could be released from the appliance.
Programme end
The programme end is indicated by:
the “Door Free” indicator coming on and the remaining time indicator (if available) showing “0:00”.
•
the programme sequence indicators are all off.
•
Turn the water supply tap off.
1.
Wait for the door to unlock (about one minute).
2.
Open the door and unload the machine.
3.
Do not fully close the door but leave it ajar to allow the drum to dry out.
N.B.
Home
Appliances
Changing programme and options
Press the
1.
Select the new programme, options and spin speed.
2.
Press the
3.
“Start/Pause”
“Start/Pause”
which the preceding one was interrupted.
For this programme do not add any further detergent.
button. The
“Start/Pause”
button flashes.
button. The new programme resumes the wash programme at the same stage at
Programme interruption or pause
To interrupt the running programme for a certain period and continue it at a later time:
Press the
1.
“Start/Pause”
button.
The indicator flashes.
Following the desired pause press the
2.
“Start/Pause”
button once again.
Cancelling the programme
If the current programme is to be terminated prematurely and cancelled, the water must be pumped
out first before the door can be opened:
Set the programme selector to programme setting
1.
The indicator above the
“Start/Pause”
button flashes. The spin indicator shows “0” and the remaining time
indicator (if available) shows “0:02” minutes.
Press the
2.
“Start/Pause”
button in order to start the
“Drain”
.
“Drain”
programme.
REMOVING THE FILTER
Switch off the appliance and unplug it.
1.
Remove the coloured insert from the detergent
2.
dispenser and use it to open the filter cover.
Place a bowl beneath the filter cover.
3.
Turn the filter slowly anti-clockwise until the grip is
4.
vertical; do not extract filter as yet.
Wait until all the water has drained out.
5.
Now unscrew the filter completely and extract it.
6.
Remove any foreign material from the filter.
7.
Make sure the pump impeller is not obstructed.
8.
Insert the filter and screw it fully down in a clockwise
9.
direction (until the grip is horizontal).
Close the cover.
10.
Pour 0.5 l of water into the detergent dispenser to
11.
reactivate the “Eco System”.
Connect the appliance to the electrical socket.
12.
Select a programme and start it.
13.
Check the filter two or three times a year and clean it if
necessary.
Check the filter if the appliance is not draining properly or
•
if it fails to perform spin cycles.
Remove the filter if the pump is blocked by an object
•
(buttons, coins, safety pins, etc.).
IMPORTANT: Make sure the water has had time to cool
before draining the appliance.
DRAINING RESIDUAL WATER
Drain the residual water as described in the “Removing the filter” chapter (points 1 to 8).
•
To drain the residual water from the pump, bend the machine frontward and operate as per points 9 and 10
•
of the previous chapter.
When should I drain residual water?
Before transporting (moving) the machine.
•
If the appliance is installed in a room subject to sub-zero temperatures. It is best in this case to drain the
•
machine after every wash.
CARE AND MAINTENANCE
Home
Appliances
Appliance exterior and control panel
Clean using a normal mild household cleaner (do not
•
use abrasive products and no solvents).
Do not use powerful cleaners that may attack the
plastic components on your washing machine.
Dry with a soft cloth.
•
Door seal
•
•
Filter
•
Detergent dispenser
Disengage the detergent dispenser by pressing the release lever
1.
in the prewash compartment and lately remove the drawer.
Remove the inserts softener compartment, the insert for
2.
liquid detergents and the siphon from the chlorine bleach
compartment, (if available, four chambers model “A”).
Wash all the parts under running water.
3.
Replace the parts and refit the detergent dispenser.
4.
Push the siphon firmly into place.
Do not operate washing machine with the detergent
N.B.
drawer removed.
Clean with a damp cloth when necessary.
Periodically check the fold of the seal for foreign
objects.
Check and clean the filter two or three times a year
(see “Removing the filter”).
A
Water hose mesh filter
Check and clean periodically.
For machines with a straight water supply hose “A”
Turn off the tap.
1.
Unscrew the hose from the tap.
2.
Clean the internal filter.
3.
Screw the supply hose back onto the tap.
4.
Unscrew the hose from the machine.
5.
Remove the filter from the washing machine with pliers and
6.
clean it.
Replace the filter and screw the hose connection back on to the
7.
machine.
Turn on the tap and
8.
completely water-tight.
ensure that the connections are
For machines with Water Stop hose “B”
Turn off the tap.
1.
Unscrew the hose from the tap.
2.
Clean the filter.
3.
Screw the Water Stop hose back onto the tap.
4.
Turn on the tap and
5.
completely water-tight.
ensure that the connection is
A
B
TROUBLESHOOTING GUIDE
Home
Appliances
This washing machine is equipped with automatic
safety functions which detect and diagnose faults
at an early stage and react appropriately.
Often, however, the faults detected are small
enough to be solved in a matter of minutes.
For example:
The appliance will not start, no lamp lights up.
Check whether:
the appliance is plugged in;
•
the wall socket is functioning correctly
•
(use a table lamp or similar);
a programme is selected correctly.
•
The appliance will not start, but the
“Start/Pause” lamp is flashing.
Check whether:
the appliance door is properly closed
•
(child safety);
the programme has been changed;
•
the water tap is open. If not, open the tap and press
•
the
“Start/Pause”
button.
The appliance stops during the programme.
Check whether:
the
•
“Rinse Hold”
by pressing the button again;
another programme has been selected.
•
Reselect the desired programme and press the
“Start/Pause”
•“Start/Pause”
button;
Pause”
Safety system of the appliance was activated.
•
See fault description table.
lamp is on, terminate this option
button;
lamp is flashing. Press
“Start/
Detergent and additive product residues in
dispenser at end of wash.
Check whether:
the siphon is correctly installed and clean
•
(see “Care and Maintenance”);
enough water is being supplied. The mesh filters
•
between the inlet hose and the tap could be clogged
(see “Care and Maintenance”). Check and clean the
filter two or three times a year (see “Removing the
filter”).
The appliance vibrates during the spin cycle.
Check whether:
the appliance is levelled and solidly installed on all
•
four feet (see “Installation Instructions”);
the transit bolts have been removed. The transit
•
bolts must be removed before the appliance can be
used (see “Installation Instructions”).
Final spin results are poor:
The appliance has an imbalance detection and
correction system. If individual heavy articles are
loaded (bathmat, bathrobe, etc.) this system may
reduce the spin speed automatically to protect the
appliance or even interrupt the spin cycle
altogether, if the imbalance is too great even after
several spin starts.
If the laundry is still too wet at the end of the cycle,
•
add smaller articles of laundry to balance the load
and repeat the spin cycle.
Excessive foam formation may prevent spinning.
•
Ensure correct amount of detergent is used
No water or insufficient water supply:
the appliance has a safety hose and the safety valve
•
has opened (red indicator in the safety valve
inspector window).
In this case replace it with a new safety hose.
What should I do when the automatic safety system detects a malfunction?
The programme is interrupted and various indicators (if available) point to the source of the fault.
Fault description table
Small lamp lights up Digital display Fault description
“Water tap” “FH”“Water inlet fault”
- “FP”“Draining fault”
- from “F4” to “F15”“Electrical components fault”
“Water Stop”“FA”“Water Stop fault”
a. Water inlet fault (no or insufficient water supply)
The “Water tap” indicator is on or the display
alternately shows “FH”. Switch off the appliance
by turning the programme selector to the “”
position and unplug it.
Check whether:
• the water tap is completely open, and the water
supply pressure is sufficient;
• the water inlet hose is kinked;
• the mesh filters are clogged (see “Care and
Maintenance” / “Water Hose Mesh Filters”);
• the water inlet hose is frozen.
Connect the appliance to the electrical supply.
Reselect the desired programme and press the
“Start/Pause” button again to continue with
the programme (do not add detergent for this
programme)
b.Draining out fault
The display alternately shows “FP”. Switch off
the appliance by turning the programme
selector to the “” position and unplug it.
Check whether:
• the drain hose is kinked (see “Installation
Instructions”);
• the pump / filter are blocked (see “Removing the
Filter / Draining Residual Water”).
IMPORTANT: before draining, allow the wash
water to cool down.
• the drain hose is frozen.
Connect the appliance to the electrical supply.
Reselect the desired programme and press the
“Start/Pause” button again to continue with
the programme (do not add detergent for this
programme). If the fault re-occurs, contact
After-Sales Service (see “After-Sales Service”).
c. Electrical module fault
The display shows “F4” to “F15”.
•Switch off the appliance. Select a programme
and press the “Start/Pause” button once
again. The programme will continue.
•If the fault re-occurs, contact After Sales
Service (See “After-Sales Service”).
d.Water Stop fault (if available)
An audible tone sounds. The light of the Water
Stop indication is on. The display shows “FA”
and the pump is running. Switch off the
appliance by turning the programme selector to
the “” position, unplug the appliance and
make sure that the water tap is closed.
The “Water Stop” may have been triggered by:
1.too much foam.
2.a leak in the inlet hose or in the appliance.
Tilt the appliance forwards carefully to allow
the collected water to flow out from the bottom
of the appliance.
Clean up the water and make the area safe.
Then:
1.connect the appliance to the electrical supply,
2.open water supply to machine (if “Start/Pause”
button is not pressed, but machine begins to fill,
close water supply and call After-Sales Service),
3. reselect the desired programme and press the
“Start/Pause” button (there is no need to add
additional detergent). The programme will continue.
If the faults occurs again, call After-Sales
Service with details about the fault (see “AfterSales Service”).
AFTER-SALES SERVICE
Before contacting After-Sales Service:
1. Try to remedy the problem yourself (see
“Troubleshooting guide”).
2.Restart the programme to check whether the
problem has solved itself.
3.If the machine continues to function incorrectly,
call After-Sales Service.
Specify:
• The nature of the problem.
The After-Sales Service sticker is on the inside
of the door.
• The exact model of the appliance (number after
the word SERVICE).
• The serial number. The number is directly below
the model number.
• Your full address.
• Your telephone number and area code. After-Sales
Service phone numbers and addresses are given on
the guarantee card. Alternatively, consult the
dealer where you purchased the appliance.
TRANSPORT AND HANDLING
Never move the appliance by carrying by the worktop.
Unplug the appliance.
1.
Turn off the tap.
2.
Remove the water supply and drain hose.
3.
Eliminate all water from the hoses and from the appliance (see “Removing the Filter”, “Draining
4.
Residual Water”).
Fit the transit bolts (obligatory)
5.
(see “Installation Instructions”).
INSTALLATION
Remove the transit bolts
Slacken the four bolts with the spanner supplied
1.
Fully unscrew the bolts by hand.
2.
Holding the bolt head, pull each bolt and plastic spacer
3.
through the wide part of the holes
Close the holes with the plastic covers supplied; insert
4.
the covers in the wide part of the hole and slide them
toward the narrow part until they click into place
Keep the transit bolts and plastic spacers for future use.
5.
Whenever the appliance is transported, the transit bolts
•
must be refitted:
Pry off the plastic covers with a screwdriver, slide them
1.
in the opposite direction of the arrow and remove.
Insert the transit bolts, performing the steps for
2.
removal in reverse order.
(Fig B)
.
(Fig A)
(Fig C)
.
.
Home
Appliances
A
B
C
Adjust the feet
If the floor is uneven, adjust the levelling feet as required
(do not insert pieces of wood etc. under the feet):
Slacken the locknut using the spanner supplied.
1.
Adjust the height of the foot, turning it by hand.
2.
Tighten the locknut by turning it anti-clockwise towards
3.
the appliance casing.
If the appliance is to be installed on a wooden floor,
distribute the weight by placing it on a 60 x 60 cm sheet
of plywood at least 3 cm in thickness.
Secure the plywood sheet to the floor.
Worktop for built-under models
The appliance
If the appliance is to be built under and the worktop removed,
UBS. This can be obtained from specialist shops or from After-Sales Service.
Unplug the appliance.
1.
Unscrew the worktop fixing screws from the rear of the appliance.
2.
Slide the worktop fully backward and lift it upwards to remove. Install the cover panel following the
3.
relative instructions.
Refit the fixing screws and tighten them.
4.
Plug the appliance only into the mains power socket.
5.
only be installed beneath a continuous fitted kitchen worktop.
must
it is mandatory
to use the cover panel
Connect the water inlet hose
For models with straight hose “A”
Insert the dirt strainer (already premounted on the hose end or
1.
included in the accessories) into the threaded tap coupling.
Carefully screw the hose connection onto the tap preferably
2.
by hand.
Make sure there are no kinks in the hose.
3.
Check water-tightness of tap and appliance connections by
4.
turning the tap completely on.
If the hose is too short, replace it with a suitable length of
pressure resistant hose (1000 kPa min, EN 50084 approved
type).
Periodically check the hose for brittleness and cracks and
replace if necessary.
The appliance can be connected without an anti-backpressure
valve.
For models with Water Stop hose “B”
If the flexible hose is damaged, unplug the appliance from
the mains immediately.
Screw the threaded connector with the filter inserted onto the
1.
tap.
Check water-tightness of tap and appliance connections by
2.
turning the tap completely on.
If the hose is too short, replace it with a 3 m Water Stop hose
(available from After-Sales Service or from your dealer). This
operation must be carried out exclusively by a licensed
electrician.
The appliance
must not
non-pressurized water heater.
The inlet hose and the plastic enclosure at the tap connection
contain electrical components.
not immerse the plastic enclosure in water.
be connected to the mixing tap of a
Do not cut the hose and do
Home
Appliances
A
B
Connect the water drain hose
Connect the drain hose to the siphon or hook it over the edge of a sink by means of the “U” bend.
1.
Make sure there are no kinks in the hose.
2.
Secure the hose so that it cannot fall down while the appliance is running.
3.
The drain hose should not be hooked onto small washbasins.
If you need to add an extension, use a flexible hose of the same type and secure the union with screw-
on hose clips.
Max. drain hose length: 2.50 m
Max. drain height: 1.25 m
U.K. ONLY
ELECTRICAL CONNECTION
Do not use extension leads or multi sockets.
Electrical connections must be made in accordance with local regulations.
1) Warning - this appliance must be earthed
This appliance is normally supplied with a mains lead having a plug fitted in the factory which has been
checked for correct earth continuity.
If the fitted plug is not suitable for your socket outlet, or if the machine’s mains lead is not fitted with a
plug, you should fit a suitable new, good quality plug by following the instructions in (2) below.
Any unsuitable plug should be cut off and disposed of in order to avoid a possible shock hazard should it
be inserted into a socket.
2) CONNECTION TO A REWIRABLE PLUG - to be carried out only by a qualified electrician
The wires in the mains lead are coloured in accordance with the following code:
BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN AND YELLOW - “EARTH” (“E”)
To fit a new plug, proceed as follows:
2.1 Polarized Plugs (e.g. 3 pin, 13 amp plug conforming to BS
1363A)
a. The GREEN AND YELLOW wire must be connected to the
terminal in the plug which is marked with the letter “E” or by
the Earth symbol or coloured green and yellow.
b. The BLUE wire must be connected to the terminal which is
marked with the letter “N” or coloured blue.
c. The BROWN wire must be connected to the terminal which is
marked with the letter “L” or coloured brown.
2.2) Non-polarized plugs (e.g. 2 pin with side earth contact)
The wire which is coloured GREEN AND YELLOW must be connected to the earth contact. The other two
wires should be connected to the two pins, irrespective of colour.
FUSE REPLACEMENT
If the mains lead of this appliance is fitted with a BS 1363A 13
amp fused plug, replace the fuse only with an A.S.T.A. approved
type conforming to BS 1362 and proceed as follows:
Remove the fuse cover (A) and the fuse (B).
Fit the replacement 13 A fuse into the fuse cover.
Refit both into the plug.
For all other types of plug, the supply socket should be protected
by a 16 A fuse or circuit breaker at the distribution board.
Printed in italy
5019 108 00366
GB
Ecological Paper
1/ 0201
Loading...