Whirlpool AKZ 307, AKZ 307 WH, AKZ 313 INSTRUCTION FOR USE
TABLE OF CONTENTS GB
INSTALLATION
ELECTRICAL CONNECTION
BEFORE USING THE APPLIANCES
PROTECTING THE ENVIRONMENT
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
ENERGY SAVING TIPS
OVEN ACCESSORIES
COOKTOP ACCESSORIES
COOKING CHARTS
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
4
6
7
7
7
8
9
9
10
CLEANING THE OVEN AND ACCESSORIES
CARE AND MAINTENANCE
OF CONVENTIONAL ELECTRIC COOKTOPS
CARE AND MAINTENANCE
OF GLASS-CERAMIC COOKTOPS
TROUBLESHOOTING GUIDE
AFTER SALES SERVICE
DECLARATION OF CONFORMITY CE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
11
13
13
13
14
14
3
INSTALLATION
Technical information for the installer
OVEN
After removing the oven from its packaging, before
•
making the connections place it on the polystyrene
foam base to protect it from damage.
Do not attempt to lift the oven by the handle.
•
Lift at the sides as shown in the figu re (see arrow).
Check that the appliance has not been d amaged in
•
transit.
Oven dimensions and kitchen unit dimensions are
•
shown in the opposite figure.
Kitchen units in contact with the oven must be heat
•
resistant (80° C).
If plastic laminates or cement are not sufficiently
•
heat-resistant, warping, bubbling or detachment of
the finish may result.
For correct ventilation, follow the ventilation
•
opening directions shown in the figure (at least
500 x 80 mm). Also provide for at least 5 mm
clearance between the top of the oven and the
lower edge of the worktop. This space must not
be obstructed by cross rails or other structural
elements.
During oven installation, care must be taken to
•
ensure that the sides are not touching the front
edges of the housing or adjacent drawers and
doors (see picture).
Carry out the electrical connections between
•
cooktop and oven (see chapter “Electrical
connection”).
Secure the oven to the kitchen unit with screws (A)
•
as shown.
4
No contacts
INSTALLATION
Cooktop
• The cooktop must be set into a worktop
between 20 mm and 50 mm thick.
There must be nothing between the cooktop
and the oven (cross rails, brackets, etc.).
• If the cooktop is to be installed next to a
column unit, leave a distance of at least 10 0mm
from the edge of the cooktop to the side of the
column unit.
Cut an opening in the worktop of the dimensions
•
shown in the Product Description Sheet supplied
separately.
If not already present, fit the supplied seal to the
•
cooktop flange after cleaning the contact area as
shown in the figure.
Cooktop with electric hotplates
• If the worktop is made of wood, fit the supplied
clips.
Position the 4 spring clips (B) and fit them in their
1.
locations on the underside of the cooktop.
Fit the cooktop into the worktop.
2.
• If the worktop is made of marble, plastic,
ceramics, natural stone, etc.,
be secured with brackets (C) code 4819 310
18528 (to be requested from After Sales Service).
Position the brackets over the holes and secure
1.
them with the supplied screws.
Fit the cooktop into the worktop.
2.
Glass-ceramic cooktop
Remove the protective film before installing the
N.B.:
cooktop.
• If the worktop is made of wood,
spring clips and screws.
Position the 4 clips (D) as shown and at the
1.
specified dimensions.
Secure the clips using screws (E).
2.
Fit the cooktop into the worktop.
3.
• If the worktop is made of marble, plastic,
ceramics, natural stone, etc.
be secured with brackets (F) code 4819 404 78697
(to be requested from After Sales Service).
Fit the cooktop into the worktop.
1.
Position the 4 brackets (F) as shown in the figure,
2.
in accordance with the thickness of the worktop.
Fix the 4 screws (G) in holes (H).
3.
the cooktop must
use the supplied
, the cooktop must
5
ELECTRICAL CONNECTION
• Make sure the appliances are installed
and connected to the electricity supply
by a qualified technician in accordance
with the manufacturer’s instructions and
in compliance with local regulations.
• The installer is responsible for the correct
electrical connection of the appliances
and the observance of the relative safety
regulations.
Connecting the oven to the power supply
Make sure that the voltage shown on the rating
•
plate is the same as the power supply voltage in
your home. The rating plate is on the front edge of
the oven cavity (visible with oven door open).
Use a type H05RR-F power cord (minimum
•
length 800 mm).
• Warning: All the oven’s components operate at
230-240 V. When using a 400 V connection,
make sure that the voltage reaching the oven is
230-240 V, as illustrated in the side table.
Conductors X
number
1N+
~
Connection
H05 RR-F 3X4 mm²
• The appliance must be connected to the
electricity supply by means of an all-pole
disconnect switch with minimum contact
gap of 3 mm.
• The appliances must be earthed by law.
• Do not use multiple plug adapters or
extension leads.
• After the appliances have been installed,
the electrical components must be
inaccessible.
2N+
3+
3N+
~
~
~
H05 RR-F 4X2,5 mm²
H05 RR-F 4X2,5 mm²
H05 RR-F 5X1,5 mm²
Interconnecting cooktop and oven
Before connecting the oven to the power supply,
•
check that the cooktop is among the ones listed in
the cooktop/oven pairing product sheet.
Connect the 3 pole and 4 pole connectors to the
respective connectors on the oven.
The 3 pole connectors (H) is located at the rear
•
right hand side of the control panel, the 4 pole
connector (J) is located at the top of the oven in the
left hand corner (see figure).
Connect the yellow/green striped earth wire ( )
•
(K) from the cooktop to the screw located near the
3 pole connector.
WARNING: DO NOT CONNECT TO THE
POWER SUPPLY BEFORE YOU HAVE
FINISHED CONNECTING THE OVEN AND
COOKTOP.
Mount the oven in the kitchen unit.
•
Make sure the power cord is not trapped.
6
Loading...