Whirlpool AKZ 131/IX/01, BMZH 5900 IN, AKZ 131/NB/01 INSTALLATION

10200198GB.fm Page 2 Wednesday, November 16, 2005 12:38 PM
INSTALLING THE BUILT-IN / UNDERCOUNTER COLUMN OVEN
The installer is responsible for connecting
Recommendations
Important: Disconnect the oven from the mains before carrying out any installation work or servicing.
technician in accordance with the manufacturer's instructions and in compliance with local regulations. Unpack the oven and make sure that the
appliance has not been damaged durin g transport and that the oven door closes properly.
are not sure contact the dealer or the nearest service centre.
After removing the oven from its packaging,
leave it on the polystyrene base to prevent it from being damaged. When installing the oven it is advisable to wear
protective gloves. Do not lift the oven by the door handle. Get hold
of it using the side openings provided.
If you
Preparing the housing unit
Kitchen units in contact with the oven must be
heat resistant (80 °C min). Cut the kitchen unit to fit before installing the
appliance. Carefully remove any shavings or sawdust that could prevent the appliance from running properly. The dimensions of the oven and unit are shown
in figures 1-2-3. To allow for proper ventilation, an opening
should be left at the bottom of the kitchen unit. Pay attention to the dimensions in the diagram.
When installation has been completed, the bottom of the oven must be inaccessible.
When installing, make sure that the sides of the oven
do not touch the adjacent kitchen units (fig.4-5). When installing ovens under the worktop, leave
a minimum clearance of 5 mm between the upper edge of the oven and the lower edge of the worktop (fig.6).
operate properly, this clearance must never be obstructed.
If the kitchen unit is not securely fixed to the wall,
it must be anchored with standard brackets (G) (fig. 7) available on the market.
In order for the appliance to
Electrical connection
Regulations require that the appliance be earthed.
Connection to the mains must be carried out by a
qualified electrician in accordance with the manufacturer's instructions and in compliance with local regulations.
2
appliances correctly to the mains and for observing the safety regulations. The oven power cable must be long enough to
connect the built-in appliance to the mains. Observance of safety directives requires that a
multi pole switch with a minimum contact gap of 3 mm be used for the installation. Do not use multiple plug adapters or extension
leads. After the oven has been installed, the electrical
components must be inaccessible.
Connecting the oven to the power supply
Make sure that the voltage indicated on the rating
plate is the same as the mains voltage. The rating plate is on the front edge of the oven (visible when the door is open). If the oven does not have a power supply cable
proceed as follows:
Remove the two fastening screws of the
1.
terminal box cover located on the bottom par t of the oven's rear covering. Remove the cover to gain access to the terminal
2.
box and insert the power cable (see table) through the opening located on the bottom of the oven. Connect the cable to the terminal box, tighten
3.
the screws as far as they will go and secure it to the cable fastener. Put the cover back on by inserting the two
4.
blades in the slots and fasten it with the two screws.
Power supply cable table
N° of conductors Type of cable 1N+
2+
~
~
Securing the oven
Lift the oven getting hold of it by the openings on
the sides and insert it into the housing unit, being careful not to trap the power supply cable (fig. 8). Center the oven in the housing unit before
securing it. Make sure that the plastic spacers (if provided)
are positioned correctly in the fastening holes. Then anchor the oven to the housing unit with the screws provided.
H05 RR-F 3 X 1.5 mm² H05 RR-F 3 X 1.5 mm²
(Switzerland only)
Fig. 3
Copertina Colonne.fm Page 1 Wednesday, January 14, 2004 10:39 AM
Fig. 2
Fig. 1
Loading...
+ 2 hidden pages