Whirlpool AKZ 104/WH, AKZ 531 WH, AKZ 531 NB, AKZ 531 IX, AKZ 194/IX Installation Manual
...
10200155aGB.fm Page 9 Monday, September 5, 2005 3:32 PM
INSTALLING THE UNDER THE COUNTER
OVEN
Recommendations
Important: Disconnect the oven from the
mains before carrying out any installation
work or servicing.
Installation must be carried out by a qualified
•
electrician in accordance with the manufacturer's
instructions and in compliance with local
regulations.
Unpack the oven and make sure that the
•
appliance has not been damaged during transport
and that the oven door closes properly.
are not sure contact the dealer or the
nearest service centre.
After removing the oven from its packaging,
•
leave it on the polystyrene base to prevent it
from being damaged.
When installing the oven it is advisable to wear
•
protective gloves.
Do not lift the oven by the door handle. Get hold
•
of it using the side openings provided.
If you
Preparing the housing unit
Built-under oven
Kitchen units in contact with the oven must be
•
heat resistant (80 °C min).
Cut the kitchen unit and worktop to fit before
•
installing the appliances. Carefully remove any
shavings or sawdust that could prevent the
appliances from running properly.
The dimensions of the oven and unit are shown
•
in figures 1-2-3.
To allow for proper ventilation, an opening
•
should be left at the bottom of the housing unit.
Pay attention to the dimensions in fig.3.
Leave a minimum clearance of 5 mm between
•
the upper edge of the oven and the lower edge
of the worktop (fig. 2)
never be obstructed.
When installing, make sure that the sides of the
•
oven do not touch the adjacent units.
If the kitchen unit is not securely fixed to the wall,
•
it must be anchored with standard brackets (G)
available on the market, see fig. 3.
This clearance must
Cooktop
Attention:
surface made of material other than wood (marble,
plastic, ceramic, stone, etc.) remember to ask After
Sales Service for the fixing plates (fig. 6-8).
The cooktop must be fitted in a worktop with a
•
minimum thickness of 20 mm and a maximum of
50 mm.
There must be nothing between the cooktop and
•
the oven (e.g. cross rails, insulating material, etc.).
An adjacent column unit must be installed at le ast
•
100 mm from the edge of the cooktop (fig. 4).
Cut an opening in the worktop of the dimensions
•
shown on the Product Description Sheet
provided with the worktop.
We recommend you seal the internal edges of
•
the worktop with wood glue or silicone.
If not already in place, apply the supplied seal to
•
the cooktop, after cleaning the adhesive surface
thoroughly.
Conventional electric cooktop
Important: Remove any protective film before
installing the cooktop.
• If the worktop is made of wood, use the
spring clips and screws provided.
1.
2.
• If the worktop is made of marble or other
material (plastic, ceramics, stone, etc.)
cooktop must be secured with special brackets
(C) (fig. 6), Code 4819 310 18528, (available as a
complete set from After Sales Service).
1.
2.
when installing the cooktop on a
Insert the 4 spring clips (B) (fig. 5) in their guides
on the bottom of the cooktop.
Fit the cooktop into the worktop.
, the
Fasten the brackets into the holes with the
screws provided.
Fit the cooktop into the worktop.
Glass-ceramic cooktop
Important: Remove any protective film before
installing the cooktop.
Make sure that that the opening in the worktop for
the cooktop is cut according to the dimensions
given in the drawing on the Product Description
Sheet. Pay attention to the tolerance range.
The cooktop should not be forced into the
worktop. Forcing the glass-ceramic top may cause
it to crack (even at a later date)!
9
10200155aGB.fm Page 10 Monday, September 5, 2005 3:32 PM
• If the worktop is made of wood
clips and screws provided.
1.
Secure the spring clips (D) (fig. 7) with the
screws provided (E) (fig.7) as shown, paying
attention to the specified distances.
2.
Fit the cooktop into the worktop.
• If the worktop is made of marble, plastic,
ceramics, stone, etc.
secured with special brackets (F) (fig. 8), Code
4819 404 78697, available from After Sales Service.
1.
Fit the cooktop into the worktop.
2.
Place the 4 brackets (F) in position in
accordance with the thickness of the worktop
as shown in fig. 8.
3.
Fasten the 4 screws (G) in the positions (H)
(fig. 8).
, the cooktop must be
, use the spring
Electrical connection
• Regulations require that the appliance be
earthed.
•
Connection to the mains must be carried out by a
qualified electrician in accordance with the
manufacturer's instructions and in compliance
with local regulations.
•
The installer is responsible for connecting
appliances correctly to the mains and for
observing the safety regulations.
•
The oven power cable must be long enough to
connect the built-in appliance to the mains.
•
Observance of safety directives requires that a
multi pole switch with a minimum contact gap of
3 mm be used for the installation.
•
Do not use multiple plug adapters or extension
leads.
•
After the oven has been installed, the electrical
components must be inaccessible.
Connecting the oven to the power supply
•
Make sure that the voltage indicated on the rating
plate is the same as the mains voltage. The rating
plate is on the front edge of the oven (visible
when the door is open).
•
Remove the two fastening screws of the terminal
box cover (if supplied) located on the bottom
part of the oven's rear covering. Remove the
cover to gain access to the terminal box and
insert the power cable (see table) through the
opening located on the bottom of the oven.
Connect the cable to the terminal box and secure
it to the cable fastener. Put the cover back on by
inserting the two blades in the slots and fasten it
with the two screws.
Power supply cables table
1N+
2+
2N+
3N+
3+
~
~
~
~
~
H05 RR-F 3 X 4 mm²
H05 RR-F 3 X 4 mm²
H05 RR-F 4 X 2.5 mm²
H05 RR-F 5 X 1.5 mm²
H05 RR-F 4 X 2.5 mm²
Interconnecting cooktop and oven
Important: do not connect the oven to the
power supply before you have finished
connecting the oven and cooktop.
•
Before connecting the oven to the power supply,
make sure that the cooktop is among the ones
listed in the cooktop/oven pairing product sheet
provided.
•
Connect the two male 3 pole (H) (fig. 9) and 4
pole (J) (fig. 9) connectors of the cooktop to the
respective female connectors located on the
right hand side of the top covering of the oven.
•
Unscrew the nut of the ground screw (K) (fig. 9)
on the left hand side of the top covering of
the oven and insert the yellow/green earth cable,
leaving the washer in place.
•
Screw the nut back onto the screw and tighten it
as far as it will go.
Securing the oven
•
Lift the oven getting hold of it by the openings on
the sides and insert it into the housing unit, being
careful not to trap the power supply cable (fig. 10).
•
Center the oven in the housing unit before
securing it.
•
Make sure that the plastic spacers (if provided)
are positioned correctly in the fastening holes.
Then anchor the oven to the housing unit with
the screws provided.
10
Loading...