Whirlpool AKM891/BA, AKZ 200 IX INSTRUCTION FOR USE
3gb54361.fm5 Page 17 Thursday, May 9, 2002 6:01 PM
INSTRUCTIONS FOR USE
INSTALLATION
ELECTRICAL CONNECTION
BEFORE USING THE APPLIANCES
SAFEGUARDING THE ENVIRONMENT
EASYTRONIC SYSTEM
POWER ADJUSTMENT
PRECAUTIONS AND GENERAL RECOMMENDATIONS
ENERGY SAVING TIPS
OVEN ACCESSORIES
COOKTOP ACCESSORIES
OVEN FUNCTIONS
COOKTOP FUNCTIONS
CLEANING THE OVEN AND ACCESSORIES
CARE AND MAINTENANCE OF THE ELECTRIC COOKTOP
CARE AND MAINTENANCE OF THE GLASS-CERAMIC
COOKTOP
TROUBLESHOOTING GUIDE
AFTER SALES SERVICE
DECLARATION OF CONFORMITY CE
17
3gb54361.fm5 Page 18 Thursday, May 9, 2002 6:01 PM
INSTALLATION
Technical information for the installer
Oven
After removing the oven from its packaging, before making the
connections place it on the polystyrene foam base to protect it
from damage.
Do not attempt to lift the oven by the handle. Lift at the sides
as shown in the figure (see arrow).
Check that the appliance has not been damaged in transit.
Oven dimensions and kitchen unit dimensions are shown in the
opposite figure.
Kitchen units in contact with the oven must be heat resistant
(80° C).
If plastic laminates or sealants are not sufficiently heat-
resistant, warping, bubbling or detachment of the finish may
result.
Install the oven in the housing, lifting it at the sides, taking
care not to trap the power cable.
For correct ventilation, follow the ventilation opening
directions shown in the figure (500 x 80 min). An additional
opening of 5 mm is required between the oven top rim and the
cooktop lower rim: this opening must not be closed by strips or
housing crosspieces.
During oven installation, care must be taken to ensure that the
sides are not touching the front edges of the housing or
adjacent drawers and doors (see picture).
Carry out the electrical connections between cooktop and oven
(see chapter Electrical Connection).
Secure the oven to the kitchen unit with screws
18
(A)
as shown.
No contacts
3gb54361.fm5 Page 19 Thursday, May 9, 2002 6:01 PM
INSTALLATION
Cooktop
The cooktop must be set into a worktop between 20 mm and
50 mm thick. There must be nothing between the cooktop
and the oven (cross rails, brackets, etc.).
Cut an opening in the worktop of the dimensions shown in the
product description sheet supplied separately.
If not already present, fit the supplied seal to the cooktop
flange after cleaning the contact area as shown in the figure.
Conventional electric cooktop
If the worktop is made of wood, fit the supplied spring
clips.
1.
Position the 4 spring clips
on the underside of the cooktop.
2.
Fit the cooktop into the worktop.
If the worktop is made of marble, plastic, ceramics, natural
stone, etc.
be requested from After Sales Service under part number 4819
310 18528.
1.
Position the brackets over the holes and secure them with the
supplied screws.
2.
Fit the cooktop into the worktop.
, the cooktop must be secured with brackets
Glass-ceramic cooktop
N.B.:
remove the protective film before installing the cooktop.
If the worktop is made of wood,
1.
Position the 4 spring clips
dimensions.
2.
Secure the spring clips using screws
3.
Fit the cooktop into the worktop.
If the worktop is made of marble, plastic, ceramics, natural
stone, etc.
code 4819 404 78697 (to be requested from After Sales
Service).
1.
Fit the cooktop into the worktop.
2.
Position the 4 brackets
accordance with the thickness of the worktop.
3.
Fix the 4 screws
, the cooktop must be secured with brackets
(G)
(B)
and fit them in their locations
fit the supplied spring clips.
(D)
as shown and at the specified
(E)
(F)
as shown in the figure, in
in holes
(H)
.
(C)
to
Top 30÷50 mm.
.
(F)
Top 30÷50 mm.
19
3gb54361.fm5 Page 20 Thursday, May 9, 2002 6:01 PM
ELECTRICAL CONNECTION
Make sure the appliance is installed and connected to the
electricity supply by a qualified technician in accordance
with the manufacturers instructions and in compliance with
local regulations.
The installer is responsible for the correct electrical
connection of the appliances and the observance of the
relative safety recommendations.
The oven must be connected to the electricity supply by
means of an all-pole disconnect switch with minimum
contact gap of 3 mm.
Regulations require that the appliance is earthed.
Do not use multiple plug adapters or extension leads.
After the oven has been installed, the electrical components
must be concealed.
Connecting the oven to the power supply
Make sure that the voltage shown on the rating plate is the
same as the power supply voltage in your home.
The service number is located on the front edge of the oven
cavity (visible when the oven door is open).
Warning: All oven's and hob's components operate
at 230V.
Interconnecting cooktop and oven
Before connecting the oven to the power supply, check that the
cooktop is among the ones listed in the cooktop/oven pairing
product sheet.
Connect the 3 pole and 4 pole connectors to the respective
connectors on the oven. The 3 pole connector
the rear right hand side of the control panel, the 4 pole
connector
corner (see figure).
Connect the yellow/green striped earth wire ( )
cooktop to the screw located near the 3 pole connector.
IMPORTANT: DO NOT CONNECT TO THE POWER SUPPLY
BEFORE YOU HAVE FINISHED CONNECTING THE OVEN AND
COOKTOP.
Mount the oven in the kitchen unit. Make sure the power cable
is not trapped.
(J)
is located at the top of the oven in the left hand
(H)
is located at
(K)
from the
20
Loading...