Page 1
31833182.fm Page 5 Wednesday, November 16, 2005 4:56 PM
GB
INSTALLATION AND USE
For installation:
coal cookers. If the installation instructions for a gas cooker specify a greater distance, then this distance must be
observed.
For installation and use:
front of the manual. The Manufacturer declines all liability for any faults, damage or fires caused by the appliance
as a result of failure to observe the instructions and recommendations given in this manual.
To install, follow steps (1Ö2Ö3Ö.....). Do not connect the appliance to the electrical power supply until
installation is completed. If the exhaust pipe is not provided, it must be purchased separately.
The hood must be installed at least 65 cm from electric cookers and 75 cm from gas, gas oil or
Before installing or using the hood, read this manual carefully. The drawings are at the
1. Control panel
2. Extractor grille or grease filter/s (on some models the filter is behind the grille)
3. Lighting unit
4. Grease filter surround (selected models only)
5019 318 33182
GB
D F NL E
P IGR
Page 2
31833182.fm Page 6 Wednesday, November 16, 2005 4:56 PM
The discharge air must not be ducted to a flue used for removing fumes produced by appliances using gas or other fuels,
but must have a separate outlet. All national regulations governing extraction of fumes must be observed.
Extractor surface release
For selected models: 292 - 515
Measurements in proportion to hood size
For selected models:
tighten the screws of the fixing clips to the
wall unit
Secure using the screws provided
Present on some models
5019 318 33182
GB
D F NL E
P IGR
To fit the grill,
use components L or
N
Page 3
31833182.fm Page 7 Wednesday, November 16, 2005 4:56 PM
PRODUCT SHEET
REPLACING BULBS:
1. Disconnect the electrical power supply.
2. Remove the grease filter support grille (
to access the lamp housing (
cover can simply be prised off using standard screwdriver (
Fig. 1
3. Remove the burnt-out bulb.
4. Refit the extractor grille or lighting unit.
).
Replace using 40 W max E14 bulbs only.
Fig. 1
REMOVING AND REPLACING OR CLEANING
THE GREASE FILTER:
1. Disconnect the electrical power supply.
2. Remove the extractor grilles or the grease filters - using parts L or
N
Fig. 1
, (
3. Release the grease filter (selected models -
4. Remove the dirty grease filter.
5. After the grease filter has been replaced or cleaned (depending on
model), refit the parts in reverse order, making sure the entire
extraction surface is covered.
).
FITTING OR REPLACING THE CARBON FILTER:
1. Disconnect the electrical power supply.
2. Remove the extractor grilles or the grease filters (
surround (
3. Rectangular filter: position the filter A so that it covers the motor
protection grille and turn the knob clockwise. To release,
proceed in reverse order.
Round filter: Insert the carbon filter over the motor protection
grille, on some models the reference mark B must line up with
the arrow C printed on the fan shroud; next, turn clockwise.
4. To remove the filter, turn the filter or knob anti-clockwise.
5. Refit the grille, the filter or the grease filter surround.
Change the carbon filter every four months.
Fig. 2
).
Fig. 2
). On some models the lamp
) or the grease filter
A -
Fig. 3
).
Fig. 1
) or the
CONTROL PANEL
A.
Light switch.
B.
Speed selector switch.
Fig. 2
Fig. 1
Fig. 3
5019 318 33182
GB
D F NL E
Fig. 4
P IGR
Page 4
31833182.fm Page 8 Wednesday, November 16, 2005 4:56 PM
SAFEGUARDING THE ENVIRONMENT
1. Packaging
Packaging materials are 100% recyclable and are marked with the
recycling symbol .Dispose of the appliance in conformity with
local environmental regulations. Packaging materials can be
dangerous for children. Keep packaging materials (plastic bags,
polystyrene, etc.) well out of their reach.
2. Product
This appliance is marked in compliance with European Directive
2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).
By ensuring that this appliance is scrapped suitably, you can help
prevent potentially damaging consequences for the environment and
health.
The symbol on the appliance or accompanying documentation
indicates that this product should not be disposed of as unsorted
municipal waste but must be taken to a collection point for the
treatment of WEEE.
Disposal must be carried out in accordance with local environmental
regulations for waste disposal.
For further information on the treatment, recovery and recycling of
this appliance, contact your competent local authority, the collection
service for household waste or the shop where you purchased the
appliance.
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
WARNING!
• Do not allow children or infirm persons to operate the
appliance without supervision.
• Make sure children do not play with the appliance.
1. Do not connect the appliance to the mains electricity supply until
installation is completed. Always disconnect the hood from the
mains before performing any cleaning or maintenance.
2. Do not “flambé” food under the hood. Naked flames could
cause a fire.
3. Do not leave pans unattended when frying. Cooking oil can
catch fire.
4. Regular cleaning and maintenance is essential to correct
functioning and good performance. Regularly remove dirt
deposits. Regularly clean or replace filters. Never use flammable
materials as hoses for extracted air.
5. If the hood is used together with non-electrically powered
appliances, ambient negative pressure must not exceed 4Pa (4 x
-5
bars). Make sure the room is adequately ventilated.
10
Electrical connections
Before connecting the hood to the power supply, make sure the
voltage specified on the dataplate matches that in your home. The
dataplate is located inside the hood behind the grease filter.
If the appliance is fitted with a power cable and plug, the plug must
be placed in an accessible position.
If the hood does not come pre-fitted with a mains plug, fit one that
conforms to applicable standards or use a double-pole switch with a
minimum breaking gap of 3 mm.
Replacement of the power supply cable with power plug or flexible
cable may only be carried out by an authorized Service Centre or a
qualified electrician.
Cleaning the hood
Warning!
could lead to fire.
Use a soft cloth with a neutral detergent. Never use abrasive
substances or alcohol.
Failure to remove oil and g r ease at least once a month
Before using the hood
Please read these instructions carefully and keep them for future
reference, in order to ensure best use of your hood.
Packaging materials can be dangerous for children. Keep packaging
materials (plastic bags, polystyrene, etc.) well out of their reach.
Make sure the hood has not been damaged during transport.
Installation, electrical connections and replacement of the mains lead
with a plug or new flexible cable must be carried out by a qualified
technician in compliance with local safety regulations.
Declaration of conformity
This product has been designed, manufactured and sold in
conformity to the following standards:
- the safety standards of the "Low Voltage" Directive 73/23/EEC
- protection requirements of “EMC” Directive 89/336/EEC
amended by Directive 93/68/EEC.
Troubleshooting guide
The hood does not work:
• Is the plug properly inserted in the power socket?
• Is there a power failure?
• Is the fuse blown?
The hood is not extracting efficiently:
• Is the right speed selected?
• Do the filters need cleaning or replacing?
• Are the air outlets blocked?
The light does not work:
• Does the bulb need replacing?
• Is the bulb correctly fitted?
• Is the fuse blown?
TECHNICAL ASSISTANCE SERVICE
Before calling the Assistance Service
1. Check if you can fix the problem yourself (see ”Troubleshooting
guide”).
2. Switch the hood off and then on again to check if the problem
has gone.
3. If the problem persists, contact the Assistance Service.
Specify:
•the nature of the problem,
• the model of hood, stated on the data plate inside the hood,
accessible by removing the grease filters.
• your full address,
• your telephone number and area code.
• the service code (the number appearing below the word
SERVICE on the data plate inside the hood behind the grease
filter).
If any repairs are needed, contact an authorised Service Centre (to
ensure that only original spare parts are used and that repairs are
made correctly).
Failure to comply with these instructions may compromise the safety
and quality of the product.
5019 318 33182
GB
GB
D F NL E
D F NL E
P IGR
P IGR
Loading...