Whirlpool AFG 8180/IX, AFG 8084/IX, AFG 8160/IX, AFG 8060 Product sheet
60301008GB.fm Page 1 Tuesday, June 21, 2005 4:01 PM
PRODUCT SHEET
1.
Compartment for freezing
2.
Control unit
3.
Area for drawers and pull-out baskets
4.
Rating plate (inside the appliance)
5.
Note: the design of drawers and accessories may vary, depending on the model.
Controls
(depending on model)
compartment - ice packs (if provided) - ice
cubes
Storage compartment
Freezer compartment
GB
A
Digital temperature display.
B
Yellow LED: indicates that the fast freeze
function is in operation.
C
Red LED: flashes to indicate that the temperature
in the freezer compartment is too high.
Switching on
1.
Plug in the appliance.
Important
If the digital display shows only an
illuminated dot, press the freezer
on/off button D.
2.
Press button G to mute the acoustic
alarm.
3.
Wait until the temperature
indicated on the digital display
reaches -12°C.
4.
Place food to be frozen and/or
already frozen food in the freezer.
D
Freezer on/off button.
E
Internal temperature control.
F
Fast freeze button.
G
Acoustic alarm mute button.
Six horizontal lines appear on the digital
display.
After about 3 seconds, when the
appliance is warm, (internal
temperature above 10°C) only the two
lines in the middle remain illuminated;
The acoustic alarm and red led C are
activated.
The acoustic alarm stops while the red
led continues to flash.
When the temperature reaches -12°C,
the red led automatically stops flashing.
60301008GB.fm Page 2 Tuesday, June 21, 2005 4:01 PM
PRODUCT SHEET
Freezer compartment temperature adjustment
The appliance is normally factory set for optimum operation at a temperature of -18°C.
To alter the internal temperature between -16°C and -24°C, proceed as follows:
Press button E once to adjust the internal temperature: the digital display shows the temperature previously
•
set.
Each time the button is pressed, the temperature setting is changed by 1°C: the value (between -16°C and
•
-24°C) blinks cyclically on the display.
Approximately 5 seconds after the button has been pressed for the last time, the set temperature is stored,
•
the display stops flashing and the current internal temperature is shown on the display.
Note:
The digital display shows internal temperature values between +10°C and -24°C.
In the event of a power failure, selected functions remain stored in the memory.
Fast freezing
The fast freeze function switches off automatically when freezing is co mplete.
Alarm signals
Signalling Cause Solution
Door open alarm
The acoustic alarm is
activated
The door has been left open for
more than 1 minute
Close the door
Temperature
alarm
Temperature
sensor alarm
Prolonged power
failure alarm
The acoustic alarm and red
led C are activated
The acoustic alarm is
activated and the display
shows “SF”
The acoustic alarm and red
led C are activated; the
display flashes, indicating the
highest temperature reached
following the power failure
The internal temperature is
above -12°C
Temperature sensor fault Contact After-sales
Prolonged lack of power
supply, causing the internal
temperature to rise to very high
values at which correct food
storage cannot be guaranteed
Press button G; wait for
the temperature to fall
below -12°C again
service
Press button G; the
display now indicates the
current internal
temperture
Note:
The temperature alarm may activate if the door is left open for a prolonged period of time or following the
introduction of fresh food in the freezer compartment; this temporary rise in temperature does not affect the
storage of already frozen food in any way.
Defrosting
Press the freezer on/off button D. An illuminated dot appears on the digital display.
1.
Unplug the appliance or switch off at the main
2.
switch.
Fit the drain in place (see figure).
3.
Follow the instructions given in the
4.
instructions booklet.
Plug in the appliance once again.
5.
Press the freezer on/off button D. Follow the steps detailed in “Switching on the
6.
appliance”.
5019 603 01008
GB NLF ED I
P
Printed in Italy 06/05
DKN FINGR S
Loading...