Whirlpool ADPL7698WH User Manual

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

5019 300 01552

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

PROGRAM SELECTION BUTTON

Push “P” button (repeatedly) until selected program number is shown on the display (P1...Px) see “Table of programs” - next page. After 3 seconds the cycle remaining time is displayed.

START/PAUSE/ RESUME BUTTON

Push this button to start the selected program: the indicator lights up and goes off at the end of the program. Press Start button or open the door during washing cycle to pause the cycle the Start Indicator blinks. To resume the cycle push Start button and close the door.

CANCEL/OFF BUTTON

Push this button to switch off the control panel. If pressed for 3 seconds when a program is running it cancels this program. If pressed for 3 seconds when the dishwasher is off, it drains the water out. If pressed during program and delayed start selection it cancels the selection and returns to previous cycle and option selection.

WATER RECYCLING INDICATOR

When lit, it indicates that standard program uses water recycling system.

MULTIZONE INDICATOR

When lit, it indicates that Multizone option is active.

KEYBOARD LOCK

INDICATOR

When lit, it indicates that keyboard lock is active.

WATER TAP C LOSE D

- Alarm

Blinks when there is no inlet water or water tap is closed.

WASH TIME DISPLAY

Indicates the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates the time remaining until program start: “h24” if above 10 hours delay time remain and “h:mm” if below 10 hours delay time remain. If “Fx Ey” messages appears on the display, see page 9 - chapter “What to do if...”.

DELAY INDICATOR

When lit, it indicates that de lay is active.

RINSE AID

INDICATOR

When lit (at the end of the cycle), the rinse aid dispenser needs to be refilled.

SALT INDICATOR

When lit (at the end of the cycle), the salt reservoir needs to be refilled.

POWERCLEAN

Thanks to the additional power jets this option provides a more intensive and powerful wash in the lower rack, in the specific area.

TAB L ET SETTING

This setting allows to optimize the cycle performances according the type of detergent used. Push the Tablet button (the indicator lights up) if you are using the combined detergents in tablet. If you are using powder or gel detergent, the Tablet indicator on the control panel has to be off.

MULTIZONE

Allows you to choose the washing zones. Press this button (repeatedly) to select the wash zones:

KEYBOARD LOCK

This option allows you to lock the buttons on the control panel. Children will not be able to accidentally start the dishwasher by pressing the buttons on the control panel when this option is selected. If you want to activate this option hold down the button for 3 seconds. Repeat the same operation to unlock the panel.

both racks 2 indicator lights

only upper rack (including cutlery rack) indicator lights

only lower rack indicator lights

ANTIBACTERIAL RINSE

This function activates an antibacterial rinse at the end of the wash cycle, guaranteeing a further reduction of bacteria. Press the button to activate or deactivate the function. This function can be used with the programs indicated in the table of programs. The dishwasher door must be kept shut for the entire duration of the program in order to guarantee reduction of bacteria. If the door is opened the indicator lamp starts flashing.

DELAYED START BUTTON

Push the button (repeatedly) to delay the start of the program. Adjustable from 0:30 to 24 hours. With each press of the button, the delay start increases by: 0:30 if selection below 4 hours, 1:00 if selection is below 12 hours, 4 hours if selection is above 12 hours. If 24 hours reached, and the button is pressed, the delayed start is deactivated

- "OFF" message is shown. Then press the START button. The delay time can be adjusted after Start key press. The dishwasher will start after the set time.

Quick reference guide

Chart

Whirlpool is a registered trademark of Whirlpool USA

EN -1-

1) Program data obtained under normal conditions and with default options on. Data may vary depending on ambient conditions and used options. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “contact@whirlpool.com”.

RECYCLING WATER SYSTEM: these programs save water in a dedicated tank. A TANK CLEANING CYCLE (at least 45 min.) is automatically run every 30 cycles or after every power off, to assure the best product conditions.

Power consumption in: Left-on mode: 1.08 W / Off-mode: 0.40 W.

Table of programs

Deter-

gent

Consumption

Drying

Phase

Programs

Available

options

Loading instructions Litres kWh

Minutes

6th Sense

PowerClean®

40-70°C

Delay

Multizone

PowerClean

Antibacterial

Rinse

Use for normal soiled dishes with dried-on food. Senses the level of soiling on the dishes and adjusts the program accordingly. When the sensor is detecting the soil level an animation appears in the display and the cycle duration is updated. The PowerClean

option is activated

automatically with this program. To deactivate, press the PowerCl ean

button on the control panel.

X 7.5-13 0.95-1.45 85-175 Full

Pre-Wash cold

Delay

Multizone

Crockery to be washed later. — 4.0 0.01 14-16 NO

Fragile 40°C

Delay

Multizone

Lightly soiled crockery, for example glasses and cups. X 10.5 0.85 105-114 Light

Rapid 45°C

Delay

Multizone

Lightly soiled crockery, with no dried-on food. X 11.0 0.85 30-50 NO

Eco

50°C

Delay

Multizone

PowerClean

Antibacterial

Rinse

Normally soiled crockery. Standard program the most efficient in terms of its combined energy and water consumption.

X 6.0 0.92 230 Full

Daily 60°C

Delay

Multizone

Antibacterial

Rinse

Normally soiled crockery. X 11.0 1.30 80-95 Full

Intensive 65°C

Delay

Multizone

PowerClean

Antibacterial

Rinse

Recommended program for heavily soiled crockery, especially suitable for pans and saucepans.

X 11.0 1.60 165-175 Full

Steam

Delay

Multizone

PowerClean

Antibacterial

Rinse

Program including steam action dedicated for heavily soiled crockery, pots and pans. Soaking or hand pretreatment is no longer needed.

X 11.0 1.75 180-190 Full

Quick reference guide

Chart

EN -2-

1- salt reservoir 2- rinse aid dispenser 3- detergent dispenser 4- racks system 5,6,7,8- available functions on the panel 9- filters 10- spray arms

Water hardness should be set

before the first wash or if water

hardness has been changed

Visual indicator (depending on the model). Unscrew cap.

Fill the salt reservoir with water

before the first wash only.

(depending on the model)

The salt level indicator lamp may remain lit at the end of several wash cycles. If the water hardness is set to level 1 (soft), no salt is required and salt indicator lamp will remain off.

Salt indicator on the control panel Salt indicator on the salt reservoir cap

The indicator lamp lights up when SALT NEEDS TO BE ADDED.

green: OK.

clear: NEEDS TO BE ADDED

Daily check

Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft 1”!)

Screw on the cap. Salt residual around the cap needs to be removed. Some salt reservoirs have a level indicator integrated in the cap (see below how to check).

- Press and hold together Program and buttons for minimum 3 seconds.

- The current water hardness setting will be visible on the display.

- Press the Program button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of the

start button will set the level back to 1).

- Wait 30 seconds (control panel switches off) or press Start/

Pause

button to save setting.

1. Ask your water supply company what the water hardness is... 2. ...enter this value

on your dishwasher

Salt required

German

degrees °dH

French

degrees °fH

English

degrees °eH

Water hardness

level

Insert value is shown

in the display

0 - 5 0 - 9 0 - 6.3 Soft 1 NO

6 - 10 10 - 18 7 - 12.6 Medium 2

YES

11 - 15 19 - 27 13.3 - 18.9 Average 3

16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4

22 - 28 38 - 50 26.6 - 35 Hard 5

29 - 35 51 - 63 35.7 - 44.1 Ve ry ha rd 6

36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7

Add salt (never add detergent!)

min. 0.8 kg/max. 1 kg

Water hardness level is factory set for medium-hard water (level 4).

Detergents

When powder or gel detergent is used, regeneration salt must be added and water hardness level must be set as indicated in the table on the right.

Also, when tablets which include salt functionality are used, regeneration salt still must be added.

Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient). Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components. The guarantee is not applicable if faults are caused by such circumstances.

How to set water hardness in order to always assure the best cleaning results

First time use

Before first use, run the appliance with detergent and without loading.

EN -3-

Daily use

Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations

Open the cover A

(press the dedicated button).

Only fill the detergent dispenser prior to starting a wash program.

Shut the cover

by pressing dedicated ribs.

If required, open the cover B (press the dedicated button).

Add rinse aid to the max. line ~150 ml

The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.

Visual indicator

Check the rinse aid indicator to check the level into the dispenser.

(depending on the model) Rinse aid indicator on the control panel Rinse aid indicator on the dispenser

The indicator lamp lights up when RINSE AID NEEDS TO BE ADDED.

dark: OK. clear: NEEDS TO BE ADDED

Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.

If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.

Use only one tablet per one cycle, only placed in detergent dispenser.

Some types of tablets may not dissolve completely during the short cycles (Fragile, Rapid, Handwash); placing the tablet on the tub bottom can help dissolving and washing.

Insert detergent: Tablet / powder / gel into the big chamber.

Please look for the recommendation of the detergent manufacturer

on the packaging of the detergent product.

Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator

Daily check

EN -4-

+ 8 hidden pages