Quick reference guide |
|
Chart |
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS! FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
ECO PROGRAM INDICATOR
When lit, it indicates that standard program is active.
MULTIZONE
INDICATOR
When lit, it indicates the wash in the upper or lower rack only.
WASH TIME DISPLAY
Indicates the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates the time remaining until program start: “h24” if above
10 hours delay time remain and “h:mm” if below 10 hours delay time remain.
If “Fx Ey” messages appears on the display, see page 8 - chapter “What to do if...”.
KEYBOARD LOCK INDICATOR
When lit, it indicates that keyboard lock is active.
PROGRAM
SELECTION BUTTON
Push “P” button (repeatedly) until selected program number is shown on the display (P1...Px) - see “Table of programs” - next page.
After 3 seconds the cycle remaining time is displayed.
MULTIZONE
Allows you to choose the washing zones. The appliance washes both racks by default (indicators are not lit).
To wash only in specific rack, press this button repeatedly:
only upper rack indicator lit
only lower rack indicator lit
KEYBOARD LOCK
This option allows you to lock the buttons on the control panel.
Children will not be able to accidentally start the dishwasher by pressing the buttons on the control panel when this option is selected. If you want to activate this option hold down the button for
3 seconds. Repeat the same
operation to unlock the panel.
POWERDRY®
This technology generates outstanding drying results thanks to a condensation process that occurs inside the dishwasher.
POWERCLEAN®
Thanks to the additional power jets this option provides a more intensive and powerful wash in the lower rack, in the specific area.
|
|
DELAY INDICATOR |
|
|
|
SALT INDICATOR |
|
RINSE AID |
||||||||||
|
When lit, it indicates that delay |
|
When lit (at the end of the |
|
INDICATOR |
|||||||||||||
|
is active. |
|
cycle), the salt reservoir needs |
|
When lit (at the end of the |
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
to be refilled. |
|
cycle), the rinse aid dispenser |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
needs to be refilled. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
WATER TAP CLOSED |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- Alarm |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Blinks when there is no inlet |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
water or water tap is closed. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TABLET
SETTING
This setting allows to optimize the cycle performances according the type of detergent used. Push the Tablet button (the indicator lights up) if you are using the combined detergents in tablet. If you are using powder or gel detergent, the Tablet indicator on the control panel has to be off.
DELAYED START BUTTON
Push the button (repeatedly) to delay the start of the program. Adjustable from 0:30 to 24 hours. With each press of the button, the delay start increases by: 0:30 if selection below 4 hours, 1:00 if selection is below 12 hours, 4 hours if selection is above 12 hours. If 24 hours reached, and the button is pressed, the delayed start is deactivated - “OFF” message is shown. Then press the START button. The delay time can be adjusted after Start key press. The dishwasher will start after the set time.
CANCEL/OFF |
START/PAUSE/ |
BUTTON |
RESUME |
Push this button to |
BUTTON |
switch off the control |
Push this button to |
panel. |
start the selected |
If pressed for 3 seconds |
program: the |
when a program is |
indicator lights up |
running it cancels this |
and goes off at the |
program. If pressed |
end of the program. |
for 3 seconds when |
Press Start button or |
the dishwasher is off, |
open the door |
it drains the water out. |
during washing cycle |
If pressed during |
to pause the cycle - |
program and delayed |
the Start Indicator |
start selection it |
blinks. |
cancels the selection |
To resume the cycle |
and returns to |
push Start button |
previous cycle and |
and close the door. |
option selection. |
|
5019 300 02471
Whirlpool is a registered trademark of Whirlpool USA |
EN -1- |
Quick reference guide |
Chart |
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
|
|
Table of programs |
|
Deter- |
|
Consumption |
Drying |
|||
|
|
|
Available |
|
|
|
|
|
||
Programs |
|
Loading instructions |
gent |
Litres |
kWh |
Minutes 1) |
Phase |
|||
|
options |
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Use for normal soiled dishes with dried-on food. |
|
|
|
|
|
|
|
|
|
Delay |
Senses the level of soiling on the dishes and adjusts the |
|
|
|
|
|
|
6th Sense® |
|
|
program accordingly. When the sensor is detecting the soil |
|
|
|
|
|
||
® |
40-70°C |
Multizone |
X |
7.5-13 |
0.95-1.45 |
85-165 |
Full |
|||
|
PowerClean® |
|
® |
|||||||
PowerClean |
|
|
PowerDry® |
level an animation appears in the display and the cycle |
|
|
|
|
|
|
|
|
duration is updated. The PowerClean option is activated |
|
|
|
|
|
|||
|
|
|
|
automatically with this program. To deactivate, press the |
|
|
|
|
|
PowerClean® button on the control panel.
Pre-Wash |
cold |
Delay |
Crockery to be washed later. |
— |
4.0 |
0.01 |
14-16 |
NO |
|
Multizone |
|||||||||
|
|
|
|
|
|
|
|
||
Fragile |
40°C |
Delay |
|
|
|
|
|
|
|
Multizone |
Lightly soiled crockery, for example glasses and cups. |
X |
10.5 |
0.85 |
105-114 |
Light |
|||
|
|
PowerDry® |
|
|
|
|
|
|
|
Rapid |
45°C |
Delay |
Lightly soiled crockery, with no dried-on food. |
X |
11.0 |
0.85 |
30-50 |
NO |
|
Multizone |
|||||||||
|
|
|
|
|
|
|
|
||
|
|
Delay |
Normally soiled crockery. |
|
|
|
|
|
|
Eco 2) |
50°C |
Multizone |
|
|
|
|
|
||
Standard program the most efficient in terms of its |
X |
10.0 |
0.822 |
200 |
Full |
||||
PowerClean® |
|||||||||
|
|
PowerDry® |
combined energy and water consumption. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
1hour Wash & Dry |
55°C |
Delay |
Light to normally soiled crockery. |
|
|
|
|
|
|
Multizone |
X |
11.0 |
1.30 |
60 |
Full |
||||
Suitable for non-dried and fresh soiling. |
|||||||||
|
|
Power Dry® |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
||
Daily |
60°C |
Delay |
|
|
|
|
|
|
|
Multizone |
Normally soiled crockery. |
X |
11.0 |
1.15 |
80-90 |
Full |
|||
|
|
PowerDry® |
|
|
|
|
|
|
|
|
|
Delay |
|
|
|
|
|
|
|
Intensive |
65°C |
Multizone |
Recommended program for heavily soiled crockery, |
X |
15.0 |
1.60 |
145-155 |
Full |
|
PowerClean® |
especially suitable for pans and saucepans. |
||||||||
|
|
PowerDry® |
|
|
|
|
|
|
|
Silent |
50°C |
Delay |
Normally soiled crockery, gentle and quiet thanks to the |
X |
14.0 |
1.20 |
290-299 |
Light |
|
Multizone |
lower spray pressure. |
||||||||
|
|
|
|
|
|
|
|||
|
|
Delay |
Program including steam action dedicated for heavily |
|
|
|
|
|
|
Steam |
|
Multizone |
|
|
|
|
|
||
|
soiled crockery, pots and pans. Soaking or hand |
X |
14.5 |
1.75 |
165-175 |
Full |
|||
|
PowerClean® |
||||||||
|
|
PowerDry® |
pretreatment is no longer needed. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1)Program data obtained under normal conditions and with default options on. Data may vary depending on ambient conditions and used options. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.
2)Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “contact@whirlpool.com”.
Power consumption in: Left-on mode: 1.50 W / Off-mode: 0.50 W.
EN -2-
How to set water hardness in order to always assure the best cleaning results |
First time use |
|
11 |
10 |
|
9 |
4 |
1 |
|
Water hardness should be set before the first wash or if water hardness has been changed
Water hardness level is factory set for medium-hard water (level 4).
Detergents
When powder or gel detergent is used, regeneration salt must be added and water hardness level must be set as indicated in the table on the right.
Also, when tablets which include salt functionality are used, regeneration salt still must be added.
-Press and hold together Program and buttons for minimum 3 seconds.
-The current water hardness setting will be visible on the display.
-Press the Program button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of the start button will set the level back to 1).
-Wait 30 seconds (control panel switches off) or press Start/Pause button to save setting.
1. Ask your water supply company what the water hardness is... |
2. ...enter this value |
|
||||||
|
|
|
|
|
|
on your dishwasher |
Salt required |
|
German |
French |
English |
Water hardness |
Insert value is shown |
||||
|
||||||||
degrees °dH |
degrees °fH |
degrees °eH |
level |
in the display |
|
|||
0 |
- 5 |
0 |
- 9 |
0 - 6.3 |
Soft |
1 |
NO |
|
|
|
|
|
|
|
|
||
6 - 10 |
10 |
- 18 |
7 - 12.6 |
Medium |
2 |
|
||
|
|
|
|
|
|
|
|
|
11 |
- 15 |
19 |
- 27 |
13.3 - 18.9 |
Average |
3 |
|
|
|
|
|
|
|
|
|
|
|
16 |
- 21 |
28 |
- 37 |
19.6 - 25.9 |
Medium-hard |
4 |
YES |
|
|
|
|
|
|
|
|
||
22 |
- 28 |
38 |
- 50 |
26.6 - 35 |
Hard |
5 |
||
|
||||||||
|
|
|
|
|
|
|
|
|
29 |
- 35 |
51 |
- 63 |
35.7 - 44.1 |
Very hard |
6 |
|
|
|
|
|
|
|
|
|
|
|
36 |
- 50 |
64 |
- 90 |
44.8 - 62.4 |
Extremely hard |
7 |
|
|
|
|
|
|
|
|
|
|
3 |
|
2 |
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft 1”!) |
|
Daily check |
|||
|
1 |
Visual indicator |
|
|
|
Screw on the cap. |
||
|
|
|
(depending |
|
|
|
Salt residual |
|
|
|
|
on the model). |
|
|
|
around the cap |
|
|
|
|
|
Unscrew cap. |
|
|
|
needs to be |
|
|
|
|
|
|
|
|
removed. Some |
5 |
6 |
7 |
8 |
|
|
|
|
salt reservoirs |
|
|
|
|
have a level |
||||
|
|
|
|
|
|
|
|
indicator |
|
|
|
|
|
|
|
|
integrated in the |
1- salt reservoir |
|
|
|
Fill the salt reservoir with water |
Add salt (never add detergent!) |
|
cap (see below |
|
2- rinse aid dispenser |
|
|
how to check). |
|||||
|
|
before the first wash only. |
min. 0.8 kg/max. 1 kg |
|
|
|||
3- detergent dispenser |
|
|
|
|
||||
|
Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient). |
|
|
|||||
4- racks system |
|
|
|
|
|
|||
|
|
|
Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components. |
|
||||
5,6,7,8- available functions on the panel |
The guarantee is not applicable if faults are caused by such circumstances. |
|
|
|
||||
9- filters |
|
|
|
|
(depending on the model) |
|
|
|
10spray arms |
|
|
|
The salt level indicator lamp may remain lit |
Salt indicator on the control panel |
Salt indicator on the salt reservoir cap |
||
11Power Dry Technology |
|
at the end of several wash cycles. If the |
|
|
|
|
||
|
|
|
|
water hardness is set to level 1 (soft), no |
The indicator lamp lights up when |
green: OK. |
clear: NEEDS TO |
|
|
|
|
|
salt is required and salt indicator lamp will |
SALT NEEDS TO BE ADDED. |
BE ADDED |
||
|
|
|
|
|
||||
|
|
|
|
remain off. |
|
|
|
|
Before first use, run the appliance with detergent and without loading. |
EN -3- |
Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator |
Daily check |
2 |
Visual |
|
|
|
indicator |
If required, open the cover B (press the dedicated button).
(depending on the model)
Add rinse aid to the max. line ~150 ml
The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.
Check the rinse aid indicator to check the |
Rinse aid indicator on the control panel |
Rinse aid indicator on the dispenser |
|
level into the dispenser. |
The indicator lamp lights up when |
dark: OK. |
clear: NEEDS TO BE ADDED |
|
RINSE AID NEEDS TO BE ADDED. |
||
|
|
|
|
|
|
|
|
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.
Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations |
Daily use |
|
|
|
|
|
|
Open the cover A |
|
3 |
(press the dedicated button). |
||
|
|
|
|
Insert detergent: Tablet / powder / gel into the big chamber. Please look for the recommendation of the detergent manufacturer
Only fill the detergent dispenser prior to starting a wash program.
on the packaging of the detergent product.
Use only one tablet per one cycle, only placed in detergent dispenser.
Some types of tablets may not dissolve completely during the short cycles (Fragile, Rapid, Handwash); placing the tablet on the tub bottom can help dissolving and washing.
Shut the cover
by pressing dedicated ribs.
EN -4-