Whirlpool ADP 7772 BR, ADP 7772 WH INSTRUCTION FOR USE

Before using the dishwasher, read the user instructions!

ADP 7772

Program selector knob

On / Off

Mains

Start button

Switches “on” when the dishwasher is operating.
Flashes when a fault occurs. Switches off at the end
of the programme.

Indicators

Add rinse aid

Add regeneration salt

Only add regeneration salt immediately
before starting a wash programme.

Wash cycle

Pre-Rinse Washing Drying

Programmes Loading instructions A B

Pre-Rinse cold
Glass 40°C
Quickwash 40°C

5)

Eco
Normal
Normal

Intensive

1) Reference programme for energy label in compliance with EN
50242 regulations;

2) Refer to “User instructions“;

3) Program data obtained in conformity with European standard EN

50242. Values may vary in relation to usage, e.g.: different loads,
water temperatures - above or below 15°C - as well as water
hardness and power supply voltage, etc.

Important information for Test Laboratories:
For detailed information on the EN comparison test and other tests, contact the following address: “[e-mail]”.

Whirlpool is a registered trademark of Whirlpool USA

Quick Reference Guide

Options

Programme

end

Programme chart

Crockery to be washed later. - - 5.0 0.02 10
Light soiling, for example glasses and

cups.
Lightly soiled crockery with no

dried-on food.
Normally soiled crockery. X - 13.0 1.35 80

50°C

1) 5)

5)

5)

Normally soiled crockery. X X 16.0 1.05 130

50°C

Normally or heavily soiled crockery. X X 16.0 1.65 90

65°C

Recommended programme for heavily
soiled crockery, especially suitable for

70°C

pans and saucepans.

4) The bacteria removal efficiency has been tested by the Institut
Pasteur de Lille (France), based on the NF EN 13697 standard of
November 2001.

5)

These programmes can be used with the Antibacterial rinse option.

Time and failure display

Indicates in hours the time remaining until the
start of the wash cycle. Toward the end of the
programme, during the drying cycle, the display
will indicate the time remaining in minutes.

“F....” Identification of faults for service technician

“Delayed start” button

The wash cycle can be programmed to start after
1 - 24 hours. With each successive touch of the
button, the delayed start indicator increases by 1
hour, and after 24 returns to 00. Then press the Start
button. The dishwasher will start at the set time.

Antibacterial rinse

This function adds an antibacterial rinse at the end
of the wash cycle, thereby guaranteeing a perfectly
clean and sanitized load. The lamp will light up when
the function is activated. If the temperature is not
maintained during the antibacterial cycle (e.g. if the
door is opened and remains open for a long time),
the lamp will start blinking to indicate that
sanitation is not guaranteed.

Detergent

2)

X - 13.0 0.90 55

X - 13.0 0.70 30

X X 17.0 1.90 125

3)

4)

Consumption

Litres kWh Minutes

5019 396 91345

(We reserve the right to make technical modifications)

GB

3)

WH/I/K/GB

How to use the appliance

Further indications are given in the single chapters and in the user instructions.

Switch on the appliance

How to fill the

detergent dispenser

Check the rinse aid level

Check the regeneration

salt level

Load the racks

Close the dishwasher door,

turn on the water tap

Select a programme

Automatic start by turning the programme selector knob (in case of
retractable knob, first press the knob to access it).

Large compartment A:
With each wash cycle.
Small compartment B:
For programmes with pre-wash only.

Mechanical indicator C.
Electric indicator on control panel (if provided).

On models with water softener
system only.

Mechanical indicator D. Electric
indicator on control panel (if provided).

Refer to the dishwasher loading instructions.

Select the desired programme.
The corresponding indicator lamp comes on.

ABC

Select options

Press the Start button

Wash cycle

Switch off the appliance

Turn off the water tap,

unload the racks

If necessary (and if provided) the corresponding indicator lamp lights up.

The selected programme is
then memorised (even in the
event of power failure).

Only after the START button has switched off: Access the knob (in case of
retractable knob, press and then release the knob).

Warning: when the door is opened steam comes out!

Unload the appliance, starting from the lower rack.

“Change programme”

Press the START button for 2 sec. until
the Start indicator lamp switches off;

Select another programme and
press the START button again.

- Only open the dishwasher if necessary
(Warning: beware of hot steam).

- If the appliance is switched off during a
wash cycle, when switched on again it
will resume the cycle from where it was
interrupted.

WH/II/K/GB

Dishwasher loading instructions and racks provided

Upper rack:

Multi-purpose support (A):

Depending on the position, for
long-handles utensils, cups and
glasses. May be used in three
different positions.

Crockery holders (B):

Depending on the position,
for example plates, cups and
long-stemmed glasses.

Revolving glass support (C):

Depending on the position, for
example small or long-stemmed
glasses.

Half Load:

Load the upper rack only.
Place the cutlery basket (D) in the

upper rack.

Rack height adjustment

(also when loaded):

• Lower adjustment: pull out the
two rack handles outwards (E)

and lower the rack.

• Upper adjustment: pull the two
handles (E) upwards until the rack
clicks into place (Factory setting).

The rack must be level on both
sides.

1)

2)

depending on the model

Lower rack:

Depending on the model with fixed
or tilting plate holders (F).

Half Load:

Load the lower rack only.
Greater washing power,

particularly for plates and
saucepans.

Cutlery basket (G) or (H):

Some models are provided with a
grid (I) that can be fitted onto the
cutlery basket to keep items
separated. Cutlery basket (D) for
appliances with half load only.
Sharp knives and forks that might
cause injury must be placed in the
cutlery basket with the handles
positioned upwards.

Only use dishwasher-proof crockery and dishes. Do not use the appliance for items not suitable for washing in a
dishwasher, for example wooden items, aluminium, plastic utensils, tin, hand-decorated crockery (unglazed), silver cutlery.

Spare parts which are sold separately:

1)

Multi-purpose support (A) - N. AMH 369 series.

2)

Revolving glass support (C) - N. WGH 1000 series.

What to do if...

If a fault occurs, before contacting our After-Sales Service, m ak e the fo ll owing che c ks to tr y and re me dy the problem
(* see also the corresponding chapter in the user instructions).

Problem Cause Remedy

The appliance is not

• No water supply. • Open the tap.

working

If crockery is not

• The appliance does not load
sufficient water.

• There is a power failure. • Insert the plug into the mains socket.

• Starting the selected programme. • The programme can be set to “0” to start.

• Insufficient rinse aid. • Increase dosage *.

• Clean the water supply tap filter.

• Ensure there are no kinks in the water hose.

• Press the Start button.

• Close the door.

• Check the domestic circuit fuse.

perfectly dry

• Residual water in cavities. • Load crockery at an angle.

If crockery is not
perfectly clean

Sandy or grainy residues

Colour of plastic parts
faded

• The water jet does not reach
the crockery.

• Insufficient detergent. • Follow recommended detergent dosage.

• Unsuitable programme. • Select a more intense wash cycle.

• Spray arms blocked. • The spray arms must be able to turn freely.

• Spray arm nozzles clogged. • Remove any impurities obstructing the water flow *.

• Incorrect detergent/detergent too old. • Use a good quality detergent.

• Clogged filters. • Check filters regularly/if necessary clean *.

• Filters incorrectly assembled. • Insert the filter correctly *.

• Tomato/carrot juice,... • Depending on the material, if necessary use a

• Arrange crockery so that items do not touch each
other.
Load crockery upside down.

detergent with a greater whitening power.

Deposits on crockery

• removable • Streaks on the crockery/glasses. • Increase the rinse aid dosage *.

• Streaks on glasses. • Reduce the rinse aid dosage *.

• Layer of salt on crockery/glasses. • Close the salt container lid properly *.

• not removable • Insufficient water softening,

Opaque glasses/ glasses

calcium deposits.

• Cannot be washed in the dishwasher. • Use suitable glasses.

• Change water hardness setting, if necessary add
salt *.

not sparkling
Rust on cutlery
Identifying appliance

faults

• Not made of stainless steel. • Use suitable cutlery.

• The START indicator lamp flashes. • Ensure that the filter assembly is not clogged and
if necessary clean it *.
Start the programme again. Press the Start button for
2 seconds, until the Start indicator lamp switches
off. Select a new programme and press the Start
button again.

• Indicator F... (if provided). • Call the After-Sales Service.

If after carrying out the above checks the malfunction persists or ap pears again, turn the appliance off and turn off the
water supply tap, then call our After-Sales Service (see guarantee).

Before contacting our After-Sales Service, take note of the following:

• The nature of the fault.

• The appliance type and model.

• The service code (the number indicated on the adhesive rating
plate) inside the door on the right-hand side.

WH/IV/GB