Whirlpool ADP 7669 IX PROGRAM CHART

.

Quick reference guide

PROGRAMME
SELECTOR
KNOB

(See Table of
programmes
below)

START BUTTON

The indicator lights up during operation, flashes when a fault occurs, and goes off
at the end of the programme.

START BUTTON RESET FUNCTION:

Press this button for at least 2 seconds; the selected programme and options will
be cancelled. Main failure displays (repeated flashing of the START indicator lamp)
can be cancelled by RESETTING. Detailed instructions are given in chapter
“What to do if...”.

START
DELAY

option

(see at right for options description)

ON/OFF

BUTTON

BEFORE USING THE APPLIANCE FOR THE
FIRST TIME CAREFULLY READ THIS QUICK
REFERENCE GUIDE AND THE INSTALLATION
INSTRUCTIONS! THE GUARANTEE IS NOT
APPLICABLE IF FAULTS ARE CAUSED BY
INCORRECT USE OF THE APPLIANCE.

Options and display description

SALT INDICATOR

When lit, the salt reservoir
needs to be refilled.

Chart

Table of programmes

P

1

2

3

4

5

6

1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary
depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of the appliance’s automatic calibration system

2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the
EN/Standard loading comparison test and other tests, contact the following address: “[e-mail]”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.

Programmes

Pre-Wash cold

Quickwash 40°C

2)

Eco

Antibacterial

Intensive 70°C

Half Load 50°C

3)

Available

options

Delay Croc ker y to b e wa shed la te r. — 5.0 0.02 10

Delay

Delay Normally soiled crockery. X 15.0 1.05 160

50°C

Delay

60°C

Delay

Delay

Loading instructions Litres kWh

Lightly soiled crockery, with no
dried-on food.

not recommended.

Normally or heavily soiled crockery,
with additional ant i bac t er ial wash.
Programme interruption (e.g. due to
door opening) can compromise
elimination of germs.

Recommended programme for
heavily soiled crockery, especially
suitable for pots and pans.

Ideal for washing a half load of
lightly or normally soiled crockery.

* Use of tablets

Detergent

X*13.0 0.70 30

X 16.0 1.75 120

X 17.0 1.65 145

X 13.0 1.00 130

Consumption

Minutes

RINSE AID INDICATOR

When lit, the rinse aid dispenser
needs to be refilled.

1)

DELAYED START
BUTTON

Press the button
(repeatedly) to delay the
start of the programme by
3, 6 or 9 hours. Then press
the START button. The
dishwasher will start at the
set time.

5019 396 01749ADP 7669

GB -1-

How to set detergent type: powder/gel/tablet (if option is available)

First time use

In order to always ensure the best cleaning
results, you NEED to set:
DETERGENT type and WATER HARDNESS.

10

S

E

L

1

3

5

1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms

2

7

9

86

1.

Select 3rd programme
(see Table of programmes

- page 1)

2.

Press ST ART button
for 7 seconds

3a.

Check your
detergent type...

Detergent

Powder or gel

(factory setting)

Tablet 2 in 1

Tablet 3 in 1

Tab l et A l l i n 1

For models without “detergent type” option, the salt and rinse aid indicators will be lit when tablets are used.

4

How to set water hardness

Switch on the appliance

*

only

before the first wash

water hardness has been changed

1.

Ask your water supply company what the

hardness

is...

German

degrees °dH

degrees °fH

0 - 5 0 - 9 0 - 6.3 Soft 1 1x

6 - 10 10 - 18 7 - 12.6 Medium 2 2x

11 - 15 19 - 27 13.3 - 18.9 Average 3 3x

16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4 4x

22 - 28 38 - 50 26.6 - 35 Hard 5 5x

29 - 35 51 - 63 35.7 - 44.1 Very hard 6 6x

36 - 60 64 - 107 44.8 - 74.9 Extremely hard 7 7x

French

or if the

English

degrees °eH

- Select the 2nd programme “P2” - consult the table of programmes.

- Press the START button for at least 5 seconds until the START indicator lamp flashes.

- The water hardness setting is shown on the display (if present) or the START button flashes.

- With each successive touch of the START button the setting increases and when it reaches 7 it returns to 1 again.

- The appliance must be switched off to memorise the new setting.

water

hardness

Water

2.

...enter this value on your dishwasher Suggestions for detergent use

Dishwasher with

display: insert value

in the display

types

3b.

...and set it on your dishwasher

using the START button

(as per table below)

Dishwasher models

model without

display

3h 6h 9h

Dishwasher without

display: count START

button led flashes

model with display

Gel or Powder

(rinse aid and

salt)

go to step 1

(see “Daily

check”)

4.

Remember to use salt and rinse
aid when needed (as indicated
below)

no symbol add salt add rinse aid

add salt

salt

Tablets

rinse aid

rinse aid

Water hardness level is factory set for
medium hard water (a number “4” is
shown on the display or the START
indicator lamp flashes 4 times).

if extra salt

is needed go

to step 1

(see “Daily

check”)

Even if you use tablets which include salt,
you must still add salt since such
detergents are not effective enough at
softening hard water.

5.

Switch off and switch on
again to save setting

GB -2-

1

Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)

Daily check

Visual indicator
(depending
on model).
Unscrew cap.

The salt level indicator lamp may remain lit for the duration of several wash cycles. If the
water hardness level falls within ca teg or y (s oft), n o s a lt is re qu ir e d.

Fill the salt
reservoir with
water before the
first wash only.

Salt indicator

(depending on

the model)

Add salt

(never add
detergent!).
min. 1.5 kg
max. 2 kg

The indicator lamp on the control panel

lights up when SALT NEEDS TO BE

ADDED.

orange: OK. clear: NEEDS TO BE ADDED

Visual indicator (depending
on model). Screw on the cap.
Salt residues around cap
need to be removed.

Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator

Visual

2

Rinse aid

indicator (depending on model)

Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.

If there are streaks: reduce the do s ag e b y tur n in g the d ia l to a low er se ttin g (1 - 3). If cr o ckery is n ot p er fe ctly d ry: in cr e as e the d os a ge by tur n in g the dia l to a hig her se ttin g (5 -6). Pla s tic dis he s have mo r e d iffic ul ty dr yin g a nd a higher ri n se ai d
setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programmes. In the case of shorter programmes, detergent residue may be a problem (if necessary, use powder detergent). Detergen ts with ri nse ai d in c or p or a ted ten d
to form excess suds.

indicator B

If required, open
the cover (press
lever).

The indicator lamp on the control panel lights up when RINSE AID NEEDS TO BE
ADDED.

Add rinse aid
to max.
line ~100 ml

The rinse aid dosage can be adjusted to the
detergent used. The lower the setting, the less
rinse aid is dispensed (factory setting: position 4).
Press the lever to open the cover. Using a coin or
similar object, turn the arrow to the desired
setting. After adjusting the rinse aid setting, shut
the cover again.

dark: OK. clear: NEEDS TO BE ADDED

Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations

Tablet / gel / powder

3

Open the cover A
(press lever).

Only fill the
detergent dispenser
prior to starting a
wash programme.

Use only one tablet per cycle,
placed in the detergent
dispenser.

Daily use

GB -3-