Whirlpool ADP 7652 A PC 6S WH INSTRUCTION FOR USE

Quick reference guide

Chart

(see at right for options description)

PROGRAM SELECTION		START/RESUME BUTTON
BUTTON		Push this button to start the selected program: the
Push “P” button (repeatedly)		indicator lights up and goes off at the end of the
until selected program number		program.
is shown on the display		When the door is opened during a washing cycle,
(P1...Px) - see “Table of		the cycle is temporarily paused: the Start indicator
programs” below.		blinks. To resume the cycle close the door and
		push Start button again.

CANCEL/OFF BUTTON

Push this button to switch off the control panel. If pressed when a program is running it cancels the program ongoing draining water for 1 minute (0:01 is shown into the display).

If pressed when the dishwasher is switched off, it drains any possible liquids from dishwasher (1 minute process).

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY

BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

Options and display description

SALT INDICATOR				RINSE AID INDICATOR
When lit (at the end of the cycle),				When lit (at the end of the cycle),
the salt reservoir needs to be				the rinse aid dispenser needs to
refilled.				be refilled.

		Table of programs			Deter-		Consumption		Drying
	Programs		Available	Loading instructions	gent	Litres	kWh	Minutes 1)	Phase
			options
P1	Sensor	40°-70°C	Delay	Recommended program for routine	X	7-14	1.00-1.60	70-155	Full
			Power Clean	washes, with dried-on food (e.g. EN
				50242).
P2	Pre-Wash	cold	Delay	Crockery to be washed later.	—	4.0	0.03	14	NO
P3	Fragile	40°C	Delay	Light soiling, for example glasses and	X	10.0	0.85	100	Light
				cups.
P4	Rapid	45°C	Delay	Lightly soiled crockery, with no dried-	X	11.0	0.80	30	NO
				on food.
P5	Eco 2)	50°C	Delay	Normally soiled crockery.	X	11.0	1.03	150	Full
			Power Clean	Energy-saving program.
P6	Fast Daily	60°C	Delay	Normally soiled crockery.	X	10.0	1.30	80	Full
P7			Delay	Program including steam action
	Steam			dedicated for heavily soiled crockery,	X	14.0	1.70	180	Full
			Power Clean	pots and pans. Soaking or hand
				pretreatment is no longer needed.
P8			Delay	Normally or heavily soiled crockery, with
	Hygiene 3)			additional antibacterial wash. Program	X	13.0	1.50	118	Full
			Power Clean	interruption (e.g. due to door opening)
				can compromise elimination of germs.

1)Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

2)Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “[e-mail]”.

3)The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.

WASH TIME DISPLAY

Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates the time remaining until program start (h.00) - below 1h (0:min).

If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.

DELAYED START BUTTON Push the button (repeatedly) to

delay the start of the program – delay indicator turns on. Adjustable from 1 to 24 hours. With each press of the button, the delay increases by one hour and after "h 24” returns to

"h 00”. When this option is selected the delay indicator turns on. Then press the START button. The dishwasher will start after the set time.

POWER CLEAN		TABLET SETTING
Thanks to the additional		This setting allows to optimize
power jets this option		the cycle performances
provides a more intensive		according the type of
and powerful wash in the		detergent used. Push the
lower rack, in the specific		Tablet button for 3 seconds
area. This option is		(until the indicator lights up) if
recommended for washing		you are using the combined
pots and casseroles (see		detergents in tablet (rinse aid,
page 4). Press this button to		salt and detergent in 1 dose). If
activate Power Clean (the		you are using powder
indicator lights up).		detergent or liquid detergent,
		the Tablet indicator on the
		control panel has to be off.

5019 396 03653

Whirlpool is a registered trade mark of Whirlpool USA	GB -1-

How to set water hardness in order to always assure the best cleaning results

First time use

	10	4
	9
	1

3 2

5

6

7

8

1- salt reservoir

2- rinse aid dispenser

3- detergent dispenser

4- racks system

5,6,7,8- available functions on the panel

9- filters

10spray arms

Water hardness should be set only before the first wash or if water hardness has been changed

Water hardness level is factory set for medium-hard water (level 4).

Even if you use tablets which include salt functionality, you must still add regeneration salt since such detergents are not effective enough at softening hard water.

At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).

-Press and hold together PROGRAM Selection and CANCEL/Off buttons for minimum 3 seconds.

-The current water hardness setting will be visible on the display.

-Press the PROGRAM Selection button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of the start button will set the level back to 1).

-Wait 30 seconds (control panel switches off) or press Start/Resume button to save setting.

	1. Ask your water supply company what the water hardness is...						2. ...enter this value on	Suggestions for detergent use
							your dishwasher
	German		French		English	Water hardness	Insert value is shown	Gel or Powder	Tablets
	degrees °dH		degrees °fH		degrees °eH	level	in the display	(rinse aid and salt)
	0	- 5	0	- 9	0 - 6.3	Soft	1
	6 - 10		10	- 18	7 - 12.6	Medium	2
	11	- 15	19	- 27	13.3 - 18.9	Average	3	go to step 1
	16	- 21	28	- 37	19.6 - 25.9	Medium-hard	4	(see “Daily	if water is
								check”)
	22	- 28	38	- 50	26.6 - 35	Hard	5		HARD extra salt
									needs to be added
	29	- 35	51	- 63	35.7 - 44.1	Very hard	6
									(go to step 1,
									“Daily check”)
	36	- 50	64	- 90	44.8 - 62.4	Extremely hard	7

Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)			Daily check
1	Visual indicator		Screw on the cap.
	(depending		Salt residual
	on the model).		around the cap
	Unscrew cap.		need to be
			removed. Some
			salt reservoir have
			a level indicator
			integrated in the
			cap (see below
			how to check).
	Fill the salt reservoir with water	Add salt (never add detergent!)
	before the first wash only.	min. 0.8 kg / max. 1 kg

Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient).

Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components.

The guarantee is not applicable if faults are caused by such circumstances.

The salt level indicator lamp may remain lit at the end of several wash cycles. If the water hardness level falls within category (soft), no salt is required.

(depending on the model)

Salt indicator on the control panel

The indicator lamp lights up when SALT

NEEDS TO BE ADDED.

Salt indicator on the salt reservoir cap

	green: OK.	clear: NEEDS TO
		BE ADDED

GB -2-

Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator

Daily check

2	Visual
	indicator

If required, open the cover B (press the dedicated button).

(depending on the model)

Add rinse aid to the max. line ~150 ml

The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4).

Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.

Check the rinse aid indicator to check the level	Rinse aid indicator on the control panel	Rinse aid indicator on the dispenser
into the dispenser.	The indicator lamp lights up when RINSE AID NEEDS	dark: OK.	clear: NEEDS TO BE ADDED
	TO BE ADDED.

Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.

If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.

Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations	Daily use

Open the cover A (press the dedicated button).

3

Insert detergent: Tablet / powder / liquid into the big chamber. Please look for the recommendation of the detergent manufacturer on the packaging of the detergent product.

Only fill the detergent dispenser prior to starting a wash program.

Use only one tablet per one cycle, only placed in detergent dispenser.

All types of tablets can be used, but for 2 in 1 type adding of salt is mandatory.

Some types of tablets may not dissolve completely during the short cycles (Rapid, Fragile, Handwash); placing the tablet on the tub bottom can help dissolving and washing.

Shut the cover

by pressing dedicated ribs.

GB -3-