Whirlpool ADP7543GG/1 Product Sheet

Quick reference guide

Chart

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ

THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

(see at right for options description)

PROGRAM SELECTION BUTTON

Push “Programs” button (repeatedly) until the indicator of the required program lights up (see “Table of programs” below).

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

Programs

Aqua Steam 40-70°C

Pre-Wash cold

Glasses 40°C

Quickwash 45°C

Eco

Daily 60°C

START/RESUME BUTTON

Push this button to start the selected program: the indicator lights up and goes off at the end of the program. When the door is opened during a washing cycle, the cycle is temporarily paused: the Start indicator blinks. To resume the cycle close the door and push Start button again.

Ta b l e o f p r o g r a m s

Available

options

Normally or heavily soiled crockery, including pots and pans. Thanks to

Delay

steam action, soaking or hand

Multizone

Power Clean

50°C

Power Clean

pretreatment is no longer needed. In addition hygiene is ensured due to the high temperature steam.

Delay

Crockery to be washed later.

Multizone

Delay

Light soiling, for example glasses and

Multizone

cups.

Delay

Lightly soiled crockery, with no dried-

Multizone

on food.

Delay

Normally soiled crockery.

Multizone

Energy-saving program.

Delay

Normally to heavily soile d crockery.

Multizone

Loading instructions

CANCEL/OFF BUTTON

Push this button to switch off the control panel. If pressed when a program is running it cancels the program ongoing draining water for 1 minute (0:01 is shown into the display). If pressed when the dishwasher is switched off, it drains any possible liquids from dishwasher (1 minute process).

Deter-

gent

X 7-14 0.99-1.80 70-160 Full

— 4.0 0.03 14 NO

X 10.0 0.85 100 Light

X 11.0 0.80 30 NO

X 11.0 1.03 170 Full

X 10.0 1.30 80 Ful l

Consumption

Litres kWh

Minutes

Drying

Phase

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING

AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

ANY BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES

Options and display description

SALT INDICATOR

When lit (at the end of the cycle), the salt reservoir needs to be refilled.

WASH TIME DISPLAY

Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates the time remaining until program start (h.00) - below 1h (0:min). If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.

MULTIZONE

Allows you to choose the washing zones. Press this button (repeatedly) to select the wash zones:

both racks

only lower rack

only upper rack

- indicator lits

POWER CLEAN

Thanks to the additional power jets this option provides a more intensive and powerful wash in the lower rack, in the specific area. This option is recommended for washing pots and casseroles (see page 4). Press this button to activate Power Clean (the indicator lights up).

TABLET SETTING

This setting allows to optimize the cycle performances according the type of detergent used. Push the Tablet button for 3 seconds (until the indicator lights up) if you are using the combined detergents in tablet (rinse aid, salt and detergent in 1 dose). If you are using powder detergent or liquid detergent, the Tablet indicator on the control panel has to be off.

RINSE AID INDICATOR

When lit (at the end of the cycle), the rinse aid dispenser needs to be refilled.

DELAYED START BUTTON

Push the button (repeatedly) to delay the start of the program. Adjustable from 1 to 24 hours. With each press of the button, the delayed start indicator increases by one hour and after 24 restarts from 0. Then press the START button. The dishwasher will start after the set time.

5019 396 01995

-1-

How to set water hardness in order to always assure the best cleaning results

First time use

1- salt reservoir 2- rinse aid dispenser 3- detergent dispenser 4- racks system 5,6,7,8- available functions on the panel 9- filters 10- spray arms

Water hardness should be set only

before the first wash or if water

hardness has been changed

Water hardness level is factory set for medium-hard water (level 4).

Even if you use tablets which include salt functionality, you must still add regeneration salt since such detergents are not effective enough at softening hard water.

At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).

Filling the salt reservoir -

The salt level indicator lamp may remain lit at the end of several wash cycles. If the water hardness level falls within category (soft), no salt is required.

Dissolve limescale (not necessary if water hardness level is set to “soft”!)

Visual indicator (depending on the model). Unscrew cap.

-Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds.

- The current water hardness setting will be visible on the display.

-Press the

- Wait 30 seconds (control panel switches off) or press Start/Resume button to save setting.

Programs

the start button will set the level back to 1).

Ask your water supply company what the water hardness is...

French

degrees °fH

0 - 9 Soft 1 10 - 18 Medium 2 19 - 27 Average 3 28 - 37 Medium-hard 4 38 - 50 Hard 5 51 - 63 Very hard 6 64 - 90 Extremely hard 7

Fill the salt reservoir with water

before the first wash only.

(depending on the model)

Salt indicator on the control panel Salt indicator on the salt reservoir cap

button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of

...enter this value on your dishwasher

Water hardness

level

Add salt (never add detergent!)

The indicator lamp lights up when SALT NEEDS TO BE ADDED.

Insert value is shown

in the display

min. 0.8 kg / max. 1 kg

Suggestions for detergent use

Gel or Powder

(rinse aid and salt)

go to step 1

(see “Daily

check”)

green: OK.

Ta bl e ts

if water is

HARD extra salt

needs to be added

(go to step 1,

“Daily check”)

Daily check

Screw on the cap. Salt residual around the cap need to be removed. Some salt reservoir have a level indicator integrated in the cap (see below how to check).

clear: NEEDS TO

BE ADDED

-2-

Adding rinse aid

(not necessary when you use tablets). How to adjust the rinse aid dosage regulator

Daily check

Visual

Check the rinse aid indicator to check the level into the dispenser.

Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.

If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.

Adding detergent -

(press the dedicated button).

Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations

Open the cover A

indicator

If required, open the cover B (press the dedicated button).

Add rinse aid to the max. line ~150 ml

(depending on the model)

Rinse aid indicator on the control panel Rinse aid indicator on the dispenser

The indicator lamp lights up when RINSE AID NEEDS TO BE ADDED.

Insert detergent: Tablet / powder / liquid into the big chamber

Only fill the detergent dispenser prior to starting a wash program.

The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.

dark: OK. clear: NEEDS TO BE ADDED

Shut the cover

by pressing dedicated ribs.

Use only one tablet per one cycle, only placed in detergent dispenser.

All types of tablets can be used, but for 2 in 1 type adding of salt is mandatory.

Daily use

-3-

+ 5 hidden pages