Whirlpool ADP 6830 WH INSTRUCTION FOR USE

Before using the dishwasher, read the user instructions!

ADP 6830		Quick Reference Guide		GB

Options

Programme selection button

On / Off button

Start button

Switches “on” when the dishwasher is operating. Flashes when a fault occurs. Switches off at the end of the programme.

Indicators

Add regeneration salt

Only add regeneration salt immediately before starting a wash programme.

Add rinse aid

Time and failure display 3)

Indicates in hours the time remaining until the start

of the wash cycle. Switches off when the

programme starts and indicates the time remaining in hours and minutes.

“F....” Identification of faults for service technician

“Delayed start” button

The wash cycle can be programmed to start after

1 - 24 hours. With each successive touch of the button, the delayed start indicator increases by 1 hour, and after 24 returns to 00. Then press the Start button. The dishwasher will start at the set time.

Antibacterial rinse 4)

This function adds an antibacterial rinse at the end of the wash cycle, thereby guaranteeing a perfectly clean and sanitized load. The lamp will light up when the function is activated. If the temperature is not maintained during the antibacterial cycle (e.g. if the door is opened and remains open for a long time), the lamp will start blinking to indicate that sanitation is not guaranteed.

“Half Load - Multizone” button

Load the upper or lower rack only.

This function can be used with any programme. Press once = upper rack

(the indication lamp comes on) Press twice = lower rack (the indication lamp comes on)

Press 3 times = Off (half load function deactivated). When washing without the top rack, press the “Half Load” button twice, or “Lower rack wash” (relative LED lights up).

		Programme chart			Detergent 2)		Consumption 3)
		Programmes		Loading instructions	A	B	Litres	kWh	Minutes
		Sensor Normal 5)	40-55°C	Automatic programme recommended
				for routine washes, with no dried-on or	X	X	10.0-13.0	0.80-1.05	60-120
				burnt food (not for EN 50242).
		Sensor Intensive 5)	60-70°C	Automatic programme recommended
				for heavily soiled crockery with dried-on	X	X	13.0-20.0	1.10-2.00	100-150
				or burnt food (for example EN 50242).
		Pre-Rinse	cold	Crockery to be washed later.	-	-	4.0	0.03	14
		Glass	40°C	Light soiling, for example glasses and	X	-	10.0	0.80	55
				cups.
		Quickwash	40°C	Lightly soiled crockery with no	X	-	10.0	0.65	30
				dried-on food.
		Normal 1) 5)	50°C	Normally soiled crockery.	X	X	13.0	1.05	160

1)Reference programme for energy label in compliance with EN 50242 regulations;

2)Refer to “User instructions”;

3)Program data obtained in conformity with European standard EN 50242. Values may vary in relation to usage, e.g.: different loads, water temperatures - above or below 15°C - as well as water hardness and power supply voltage, etc.

4)The bacteria removal efficiency has been tested by the Institut Pasteur de Lille (France), based on the NF

EN 13697 standard of November 2001.

5)These programmes can be used with the Antibacterial rinse option.

Important information for Test Laboratories:

For detailed information on the EN comparison test and other tests, contact the following address: “[e-mail]”.

Whirlpool is a registered trademark of Whirlpool USA	5019 396 91530
	(We reserve the right to make technical modifications)

WH/I/B/GB

How to use the appliance

Further indications are given in the single chapters and in the user instructions.

Switch on the appliance

Fill the detergent dispenser

Check the rinse aid level

Check the regeneration salt level

Load the racks

Close the dishwasher door, turn on the water tap

Select a programme

Select additional options

Press the Start button

Wash cycle

Switch off the appliance

Turn off the water tap, unload the racks

Press the ON / OFF button.

Compartment A:
With each wash cycle.			A	B C
Compartment B:
For programmes with pre-wash only.
Mechanical indicator lamp C.
Electric indicator on control panel (if provided).
On models with water softener
system only.
Mechanical indicator lamp D. Electric
indicator on control panel (if provided).
Refer to the dishwasher loading instructions.

The last programme selected will light up.

Select the desired programme (using the specific button or knob). The corresponding indicator lamp lights up.

If necessary (and if provided).

The corresponding indicator lamp lights up.

The selected programme is then memorised (even in the event of power failure).

“Change programme in progress”

Press the START button for 2 sec. until the Start indicator lamp switches off.

Select another programme and press the START button again.

-Only open the dishwasher if necessary (Warning: beware of hot steam).

-If the appliance is switched off during a wash cycle, when switched on again it will resume the cycle from where it was interrupted.

Only after the START button has switched off: Press the ON / OFF button. All the indicator lamps switch off.

Warning: When the door is opened steam comes out!

Unload the appliance, starting from the lower rack.

WH/II/B/GB