Whirlpool ADP 6830/5 WH INSTRUCTION FOR USE
Before using the dishwasher, read the user instructions!
ADP 6830
Indicators
Quick Reference Guide
Programme selection button
On / Off button
Start button
Switches “on” when the dishwasher is
operating. Flashes when a fault occurs.
Switches off at the end of the programme.
Add regeneration salt
Only add regeneration salt immediately
before starting a wash programme.
Add rinse aid
Options
GB
Time and failure display
Indicates in hours the time remaining until the start
of the wash cycle. Switches off when the
programme starts and indicates the time remaining
in hours and minutes.
“F....” Identification of faults for service technician
“Delayed start” button
The wash cycle can be programmed to start after
1 - 24 hours. With each successive touch of the button,
the delayed start indicator increases by 1 hour, and
after 24 returns to 00. Then press the Start button.
The dishwasher will start at the set time.
Antibacterial rinse
This function adds an antibacterial rinse at the end of
the wash cycle, thereby guaranteeing a perfectly clean
and sanitized load. The lamp will light up when the
function is activated. If the temperature is not
maintained during the antibacterial cycle (e.g. if the
door is opened and remains open for a long time), the
lamp will start blinking to indicate that sanitation is
not guaranteed.
“Half Load - Multizone” button
Load the upper or lower rack
This function can be used with any programme.
Press once = upper rack
(the indication lamp comes on)
Press twice = lower rack
(the indication lamp comes on)
Press 3 times = Off (half load function deactivated).
3)
4)
.
only
Programme chart
Detergent
Programmes Loading instructions A B
Sensor Normal
Sensor Intensive
5)
5)
Pre-Rinse cold
Glass 40°C
Quickwash 40°C
Normal
1) Reference programme for energy label in compliance with EN
50242 regulations;
2) Refer to “User instructions”;
3) Programme data obtained in conformity with European
standard EN 50242. Values may vary in relation to usage, e.g.:
different loads, water temperatures - above or below 15°C - as
well as water hardness and power supply voltage, etc.
Important information for Test Labo r atories:
For detailed information on the EN comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
Whirlpool is a registered trademark of Whirlpool USA
1) 5)
Automatic programme recommended
for routine washes, with no dried-on or
40-55°C
burnt food (not for EN 50242).
Automatic programme recommended
for heavily soiled crockery with dried-on
60-70°C
or burnt food (for example EN 50242).
Crockery to be washed later. - - 4.0 0.03 14
Light soiling, for example glasses and
cups.
Lightly soiled crockery with no
dried-on food.
Normally soiled crockery. X X 13.0 1.05 170
50°C
4) The bacteria removal efficiency has been tested by the Institut
Pasteur de Lille (France), based on the NF
EN 13697 standard of November 2001.
5) These programmes can be used with the Antibacterial rinse
option.
(We reserve the right to make technical modifications)
X X 10.0-13.0 0.80-1.05 60-120
X X 13.0-20.0 1.10-2.00 100-150
X - 10.0 0.80 55
X - 10.0 0.65 30
2)
Consumption
Litres kWh Minutes
5019 396 91598
3)
How to use the appliance
Further indications are given in the single chapters and in the user instructions.
Switch on the appliance
Fill the detergent dispenser
Check the rinse aid level
Check the
regeneration salt level
Load the racks
Close the dishwasher door,
turn on the water tap
Select a programme
Press the ON / OFF button.
Compartment
With each wash cycle.
Compartment
For programmes with pre-wash only.
If using combined action dishwasher
tabs, follow the user instructions!
Mechanical indicator lamp C.
Electric indicator on control panel (if provided).
On models with water softener
system only.
Mechanical indicator lamp D. Electric
indicator on control panel (if provided).
Refer to the dishwasher loading instructions.
The last programme selected will light up.
Select the desired programme (using the specific button or knob).
The corresponding indicator lamp lights up.
A:
B:
ABC
Select additional options
Press the Start button
Wash cycle
Switch off the appliance
Turn off the water tap,
unload the racks
If necessary (and if provided).
The corresponding indicator lamp lights up.
The selected programme is
then memorised (even in the
event of power failure).
Only after the START button has switched off: Press the ON /
All the indicator lamps switch off.
Warning: When the door is opened steam comes out!
Unload the appliance, starting from the lower rack.
“Change programme in progress”
Press the START button for 2 sec. until the
Start indicator lamp switches off.
Select another programme and press the
START button again.
- Only open the dishwasher if necessary
(Warning: beware of hot steam).
- If the appliance is switched off during a
wash cycle, when switched on again it
will resume the cycle from where it was
interrupted.
OFF
button.
Loading...