Page 1
Quick reference guide
Chart
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULL Y READ
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
(see at right for options description)
PROGRAMME
SELECTION BUTTON
Push “Programs” button
(repeatedly) until the indicator
of the required programme
lights up (see “Table of
programmes” below).
P
1
2
3
4
5
6
1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional
options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of
the appliance’s automatic calibration system.
2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on
the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
Programmes
Aqua Steam 40-70°C
Pre-Wash cold
Glasses 40°C
Quickwash 45°C
Eco
Daily 60°C
START/RESUME BUTTON
Push this button to start the selected programme:
the indicator lights up and goes off at the end of the
programme. When the door is opened during a
washing cycle, the cycle is temporarely paused: the
Start indicator blinking. To restart the cycle close
the door and push Start button again.
Table of programmes
Available
options
Delay
Multizone
Power Clean
Delay
Multizone
Delay
Multizone
Delay
Multizone
2)
50°C
Delay
Multizone
Power Clean
Delay
Multizone
BUTTON
Push this button to switch on or switch off the control panel.
If pressed when a programme is running it cancels
the programme ongoing.
Loading instructions
Normally or heavily soiled crockery, including
pots and pans. Thanks to steam action, soaking
or hand pretreatment is no longer needed. In
addition hygiene is ensured due to the high
temperature steam.
Crockery to be washed later.
Light soiling, for example glasses and cups.
Lightly soiled crockery, with no dried-on
food.
Normally soiled crockery.
Normally to heavily soiled crockery.
Deter-
Consumption
gent
Litres kWh
X 7-15 0.99-1.75 65-205
— 4.0 0.03 14
X 10.0 0.85 100
X 11.0 0.80 30
X 12.0 1.05 150
X 13.0 1.25 120
Minutes
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
AUTOMATICALLY AFTER 30 SECONDS IF ANY CYCLE IS STARTED.
ANY BUTTON.
Options and display description
SALT INDICATOR
When lit (at the end of the cycle),
the salt reservoir needs to be
refilled.
WASH TIME DISPLAY
Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates
the time remaining until programme start (h.00) - below 1h (0:mim).
If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.
MULTIZONE
Allows you to choose the washing
1)
zones. Press this button (repeatedly)
to select the wash zones:
both racks
only lower rack
only upper rack
- indicator lits
POWER CLEAN
Thanks to the additional power jets
this option provides a more intensive
and powerful wash in the lower rack,
in the specific area. This option is
recommended for washing pots and
casseroles (see page 4). Press this
button to activate Power Clean (the
indicator lights up).
TABLET SETTING
This setting allows to
optimize the cycle
performances according
the type of detergent
used. Push the Tablet
button for 3 seconds (until
the indicator lights up) if
you are using the
combined detergents in
tablet (rinse aid, salt and
detergent in 1 dose). If you
are using powder
detergent or liquid
detergent, the Tablet
indicator on the control
panel has to be off.
RINSE AID INDICATOR
When lit (at the end of the cycle),
the rinse aid dispenser needs to
be refilled.
DELAYED ST ART
BUTTON
Push the button
(repeatedly) to delay the
start of the program.
Adjustable from 1 to 24
hours. With each press of
the button, the delayed
start indicator increases
by one hour and after 24
restarts from 0. Then
press the START button.
The dishwasher will start
after the set time.
5019 396 01847ADP 6743/1
GB
-1-
Page 2
How to set water hardness in order to always assure the best cleaning results
First time use
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
Water hardness should be set only
before the first wash or if water
hardness has been changed
1.
Ask your water supply company what the
water hardness is...
French
degrees °fH
0 - 9 Soft 1
10 - 18 Medium 2
19 - 27 Average 3
28 - 37 Medium-hard 4
38 - 50 Hard 5
51 - 63 Very hard 6
64 - 107 Extremely hard 7
At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).
Filling the salt reservoir -
1
The salt level indicator lamp may remain lit
at the end of several wash cycles. If the
water hardness level falls within category
(soft), no salt is required.
Water hardness
Dissolve limescale (not necessary if water hardness level is set to “soft”!)
Visual indicator
(depending
on the model).
Unscrew cap.
- Press and hold together Programs and buttons for minimum 3 seconds.
- The current water hardness setting will be visible on the display.
-Press the Programs button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of
the start button will set the level back to 1).
- Wait 30 seconds (control panel switches off) or press START/Resume button to save setting.
level
2.
...enter this value on your
dishwasher
Insert value is shown
in the display
Suggestions for detergent use
Gel or Powder
(rinse aid and salt)
go to step 1
(see “Daily
check”)
HARD extra salt
needs to be added
Tablets
if water is
(go to step 1,
“Daily check”)
Water hardness level is
factory set for medium-hard
water (level 4).
Even if you use tablets which
include salt functionality, you
must still add regeneration
salt since such detergents are
not effective enough at
softening hard water.
Daily check
Fill the salt reservoir with water
before the first wash only.
(depending on the model)
Salt indicator on the control panel Salt indicator on the salt reservoir cap
The indicator lamp lights up when SALT
NEEDS TO BE ADDED.
Add salt (never add detergent!)
min. 1.5 kg / max. 2 kg
orange:
OK.
Screw on the cap.
Salt residual
around the cap
need to be
removed. Some
salt reservoir have
a level indicator
integrated in the
cap (see below
how to check).
clear: NEEDS TO
BE ADDED
GB
-2-
Page 3
Adding rinse aid
(not necessary when you use tablets). How to adjust the rinse aid dosage regulator
Daily check
Visual
2
Check the rinse aid indicator to check the level
into the dispenser.
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the
appliance.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty
drying and a higher rinse aid setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programmes. In the case of shorter programmes, detergent residue may be a problem (if necessary, use powder detergent). Detergents
with rinse aid incorporated tend to form excess suds.
Adding detergent -
(press the dedicated button).
Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Open the cover A
3
indicator
If required,
open the
cover B
(press the
dedicated
button).
Add rinse aid
to the max.
line ~150 ml
(depending on the model)
Rinse aid indicator on the control panel Rinse aid indicator on the dispenser
The indicator lamp lights up when RINSE AID NEEDS
TO BE ADDED.
Insert detergent: Tablet / powder / liquid into the big chamber
Only fill the
detergent dispenser
prior to starting a
wash programme.
The rinse aid dosage can be
adjusted to the detergent used.
The lower the setting, the less
rinse aid is dispensed (factory
setting: position 4).
Press the button to open the
cover B. Using a coin or similar
object, turn the arrow to the
desired setting. After adjusting
the rinse aid setting, shut the
cover again.
dark: OK. clear: NEEDS TO BE ADDED
Shut the cover
by pressing dedicated ribs.
Use only one tablet per one cycle, only
placed in detergent dispenser.
All types of tablets can be used, but for
2 in 1 type adding of salt is mandatory.
Daily use
GB
-3-
Page 4
How to load UPPER RACK
A - Glass-holder for long stem glasses: it can be
adjusted in 2 different positions according glasses shape.
4
B - Adjustable flaps: in horizontal position for cups/
long utensils, in raised position for plates.
(in some models only)
C - Cutlery basket: it can be placed in the upper rack
when the “Half load/Multizone” option is selected.
How to load the racks
How to adjust upper rack height
It could be useful to lift up the upper rack to have
more space in lower rack or bring it down to load
long stem glasses.
- Grasp and take out the two lateral handles (D)
(they must be on the same level)
down the upper rack.
How to remove the upper rack (if available)
It could be useful to remove the upper rack to load bulky items in the lower rack.
- Open the two retainers (E) to take off the upper rack (when the upper rack is in place
the retainers must always be closed).
(if available).
and lift up or take
How to load LOWER RACK
F - Vertical plate holders: They can be folded down to load pots.
G - Cutlery basket
H - Grid: Helps to keep separate the cutlery for better washing
results.
Power Clean use the special
water jets in the rear of cavity to
wash more intensively the high
dirty items.
1. Adjust the Power Clean area (I) folding down the rear
plate holders to load pots.
G
Arrange crockery so that water does not collect in cavities, ensuring that the spray arms turn freely. Only use dishwasher-proof crockery and dishes. Do not use the dishwasher for washing wooden
items, aluminium, tin, silver cutlery or decorated crockery (unglazed). In the baskets, dishes (e.g. plates, bowls, pots) must be placed in a correct way to let water flow down!
5
Switching on the appliance. Press any button to exit Standby and enter programme selection mode.
E - CLOSED
How to use Power Clean
2. Load pots and casseroles inclined vertically in Power
Clean area.
power water jets.
E - OPEN
Pots have to be inclined towards the
GB
-4-
Page 5
Select programme
Overview of programmes
The max. possible number of programmes is illustrated in the chapter “Chart”. The corresponding programmes for your appliance can be found on the panel (page 1).
6
Wash cycle
The dishwasher door must be closed and the water tap open.
To pause the programme (e.g. if you want to insert an item):
7
- Open the door with caution (the programme pauses) and insert
the item/s,
(beware of HOT steam!)
- Close the door and press the
cycle (the programme resumes the cycle from where it was
interrupted).
Switch off the appliance Everything o.k. ...
Exercise caution when opening the door: beware of hot steam.
Only press the button once to turn the appliance into Standby mode.
8
All the indicator lamps switch off. Unload the appliance, starting from the lower rack in order to avoid any residual drips of water falling onto crockery below.
Quick, permanent or alternating
Choose programme according to the attached table of programmes (page 1).
Duration of the programme depends on the external conditions in the apartment, temperature and pressure etc.
To Cancel the programme on running:
- Press the button .
.
START
button again to restart the
- (Water drains for up to 30 seconds then
the appliance switches off).
To change the programme in progress:
- Press the button
- (Water drains for up to 30 seconds then the appliance switches off).
- Press any button to switch on the appliance.
- Select a new programme.
- Press the
START
to cancel the programme on running.
button.
Maintenance and care
9
Filter
Check and
clean if
necessary
Rectifying minor faults yourself ...
10
Spray arms
Remove
blockages/
deposits.
Unscrew filter
cylinder , remove it
and fine sieve...
Unscrew
and remove
lower arm ...
Unscrew
and remove
upper arm ...
Rinse under running
water...
Clean spray
nozzles under
running water
(use toothpicks
if necessary) ...
Maintenance and care
Screw on filter cylinder NOTE MARK!
Insert
Insert and screw on lower and upper arms tightly.
GB
-5-
Page 6
What to do if...
If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem.
Most faults can be remedied by taking the courses of action, quickly restoring normal appliance operation.
How the faults are shown on the display: Function number “F”x - blinking Error number “E”y - blinking 0.5 sec. pause
...is not working/will not start
Crockery and cutlery... Possible causes... Solutions...
...shows “F6 E2”
...shows “F6E7” or “F6E1”
...shows “F6 E3”/wash program ended too
early (dishes are dirty and wet)
...shows “F8 E1”
Crockery and cutlery... Possible causes... Solutions...
...are not perfectly clean/have food residues
- The appliance must be switched on. - Check the household circuit fuse if there is no power supply.
- The dishwasher door doesn’t close. - Check if the dishwasher’s door is closed.
- “Delayed start” option is ON.
- Water tap closed. - The water tap must be open.
- Kinked water inlet hose or clogged inlet filters. - The water inlet hose must not be kinked and the relative inlet filter in the water tap connector must not be clogged.
- Water pressure too low. - The water tap must be fully open during water inlet (minimum capacity: 0.5 litres per minute).
- Kinked water inlet hose or clogged inlet filters. - The water inlet hose must not be kinked and the relative inlet filter in the water tap connector must not be dirty.
- Dirty or clogged filters. - The filters must not be dirty or clogged.
- Too little water in the dishwasher’s water system. - Concave items (e.g. bowls, cups) must be arranged facing downwards in the rack.
- Drain hose incorrectly fitted.
- High level of foam inside. - Repeat without detergent or wait until foam disappears.
-Dirty filters. - Clean the filters.
- Kinked drain hose. - The drain hose must not be kinked.
- Syphon hose connection closed. - The closure disk of the syphon hose connection must be removed.
- Check whether the “Delayed start” option (if available) has been selected. If it has, the appliance will only start once the set
time has elapsed. If necessary, set the delayed start to “0” (RESET the appliance).
- The drain hose must be fitted correctly (for high mounted appliances, leave min. 200-400 mm from the lower edge of the
appliance) - see Assembly instructions.
After taking the above course of action, the fault message must be reset. In the majority of cases the fault is thus eliminated.
RESET: Press the button .
Close the door.
Water drains automatically for up to 30 seconds.
The appliance is now ready to be restarted.
- Too little space between dishes (incorrect arrangement of the
concave items in the rack).
- T oo little detergent; detergent too old or incorrectly stored.
- Temperature not high enough for heavily soiled crockery. - For heavily soiled crockery, select a wash programme with a higher temperature (see table of programmes - page 1).
- Loading of the dishwasher using lower and upper rack at the
same time with “Half load/Multizone” option.
- Frequent use of Eco 50°C.
- Clogged spray arms, dirty filters or not fitted correctly. - The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see page 5, “Maintenance and care“).
- Spray arms stuck impeded by crockery or cutlery. - The spray arms must be able to turn freely and must not be impeded by crockery or cutlery.
- Arrange crockery so that items do not touch each other. Concave items (e.g. bowls, cups) must be arranged facing
downwards in the rack.
- If necessary, use more detergent, observing the manufacturer’s indications as regards dosage. Always store detergent in a
dry place and do not store it for excessively long periods of time.
- If you select the “Half load/Multizone” option (if available), remember to load
increase washing power and thus obtain optimum wash results.
- In the event of frequent use of the Eco 50°C programme (if available), from time to time select the Intensive 70°C
programme (if available).
only
the upper rack or
only
the lower rack to
GB
-6-
Page 7
What to do if...
Crockery and cutlery... Possible causes... Solutions...
...salt indicator lit
...have deposits: regeneration salt residue - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2, “How to set water
...are not dry
...have discoloured plastic parts - Tomato/Carrot juice. - Tomato sauce, for example, can lead to discolouring of plastic parts. Powder detergent is recommended as
...opaque glasses, etc.
...removable deposits on glasses - Usage of incorrect programmes for glasses. - Dishes should be put together, to avoid touching each other. Do not put glassware together in baskets.
...glasses not sparkling - Not conform of glasses to washing in dishwashers
...permanent deposits on glasses
...tea cups darken and dirt does not
disappear after washing in dishwasher
...rust marks
...other marks - Rinse aid dosage too low. - In the presence of marks, increase the rinse aid dosage (see page 3, “Adding rinse aid”).
...streaks
...suds - Unsuitable dosage of detergent/rinse aid. - Only use the amount of detergent/rinse aid required, since excessive amounts can lead to excess suds.
- Use tablets for soft water. - Set “Tablet” option; if this option is not available, it is normal for the salt indicator to light up.
hardness”).
- Salt reservoir cap open. - Close the salt reservoir cap properly.
- Not enough rinse aid. - If you use a combined action detergent, try adding more rinse aid.
- Plastic containers dry badly. - Synthetic materials do not dry well; if wet at end of cycle, wipe dry.
- Clean dishes left in dishwasher for a long time after end
of cycle (e.g. when using “Delayed start” option).
- Incorrect arrangement of the concave items in the rack. - Arrange crockery so that water does not collect in cavities.
- Incorrect dosage the rinse aid. - Increase the dosage of rinse aid (see page 3, “Adding rinse aid”).
- Rapid programme selected. - The rapid programme is intended for quickly washing lightly soiled dishes. If used for a full load of medium/
- Dishes unsuitable for washing in dishwashers (por celain), - Only use dishwasher-proof crockery and dishes.
(porcelain).
-Rainbow effect. - This phenomenon is irreversible. We recommend in future:
- Not known.
- Pre-wash programme not used. - Salty or acidic food residues can cause rust marks even on stainless steel cutlery. To avoid this, always use
- Rinse aid dosage too high. - In the presence of streaks, reduce the rinse aid dosage (see page 3, “Adding rinse aid”).
- In this situation, the presence of drops of water on dishes and on the sides of the dishwasher is normal.
Try releasing the door 5 minutes before removing the dishes.
heavy soiled dishes, the dishes may not dry completely. If so, select a standard-length programme. For best
results, open the door after the end of the programme and wait 15 minutes before unloading the dishwasher.
it allows slightly higher doses to be used for improved whitening. Programmes with higher wash
temperatures should be used.
Use suitable programme for glass.
- Some kinds of glass cannot be washed in the dishwasher.
- Change the control of system of dosage of softener.
- Be careful – follow recommended detergent dosage.
- For combined action tablets see detergent producer’s recommendations.
- This phenomenon is inevitable. Theine alters colours permanently.
the pre-wash programme if the dishes are to be washed later.
- If you use a combined action detergent, possibly add more rinse aid.
- If you use a combined action detergent which includes rinse aid, do not add any additional rinse aid.
GB
-7-
Page 8
Disconnect the mains plug
If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty).
Before contacting our After-Sales Service, take note of the following:
- the description of the fault,
- the appliance type and model,
- the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side:
Precautions and general recommendations
What to do if...
1. Packing
The packaging materials are 100% recyclable and marked with the recycling symbol .
2. Removing the packaging and inspecting the contents
After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt,
contact a qualified technician or your local retailer.
3. Before using the dishwasher for the first time
- The appliance is designed to operate at ambient temperatures of between 5°C and 45°C.
- This dishwasher has been tested by the manufacturer to ensure it functions correctly. Such testing may
leave slight drips/water marks which will disappear with the first wash.
4. Energy and water savings
- Do not rinse crockery under running water.
- Always fully load the dishwasher before running it or select the “Half load/Multizone” option (if available).
- If ecological energy sources are available such as solar panel heating, heat pumps or centralised heating
systems, the appliance may be connected to the hot water mains up to a maximum temperature of 60°C.
Make sure the water inlet hose is of the correct type (“70°C Max” or “90°C Max”).
5. Child safety
- Keep the packaging materials out of the reach of children.
- Children must not be allowed to play with the dishwasher.
- Store the detergent, rinse aid and salt out of the reach of children.
6. Safety warnings
- The appliance is not intended for use by children or physically or mentally impaired persons, unless
adequately supervised by a responsible adult capable of guaranteeing safe use of the appliance.
- Do not operate the appliance in the open air.
- Do not store flammable materials in close proximity to the dishwasher.
- The water in the dishwasher is not potable.
- Do not use solvents inside the dishwasher: risk of explosion!
- Be careful when the door is open: risk of tripping!
- The open dishwasher door can only support the weight of the loaded rack when pulled out. Do not rest
objects on the open door or sit or stand on it.
- Sharp items that might cause injury (e.g. knives), must be placed in the cutlery basket with the sharp end
facing downwards. Long-handled utensils must be arranged horizontally in the upper rack, with the sharp
end facing away from the front of the appliance.
The guarantee is not applicable if faults are caused by incorrect use of the appliance.
We reserve the right to make technical modifications.
- Before cleaning or carrying out maintenance, disconnect the mains plug and turn off the water tap; also in
the event of any malfunction.
- Repairs and technical modifications must be carried out exclusively by a qualified technician.
7. Resistance to frost
If the appliance is placed in surroundings exposed to the risk of frost, it must be drained completely. Turn off
the water tap, remove the inlet and outlet hoses, and let all the water drain away. Make sure there is at least
1 kg of dissolved regeneration salt in the salt reservoir, to protect the appliance from temperatures of up to
-20°C. When the programme resumes, an error message may be indicated (see page 6).
“F6 E2” - the appliance must remain at an ambient temperature of min. 5°C for at least 24 hours.
After eliminating these faults, RESET the appliance (see chapter “What to do if...”).
8. Disposal
- The appliance is manufactured using recyclable materials. If you decide to scrap the dishwasher, it must be
disposed of in compliance with local waste disposal regulations. Make it unusable by cutting off the power
cord. To prevent situations of potential danger to children (e.g. danger of suffocation), break the lock of the
door so that it can no longer be closed.
- This appliance is marked according to the European directive 2002/96/CE on Waste Electrical and
Electronic Equipment (WEEE). By ensuring that this appliance is scrapped suitably, you can help prevent
potentially damaging consequences for the environment and health. Unsuitable disposal of an appliance of
this type as household waste could have detrimental effects on the environment. The symbol on the
appliance, or on documentation enclosed with the appliance, indicates that this product must not be
treated as household waste, but must be delivered to the nearest collection centre for the recycling of
electrical and electronic appliances. Disposal must be carried out in accordance with local environmental
regulations for waste disposal. For further information on the treatment, recovery and recycling of this
appliance, contact your competent local authority, the collection service for household waste or the shop
where you purchased the appliance.
EC Declaration of conformity
This appliance has been designed, constructed and distributed in compliance with the safety requirements of
EC Directives: 2006/95/CE, 89/336/CE, 93/68/CE and 2002/95/CE (RoHS Directive).
Loading Capacity: 12 place settings.
GB
-8-
Loading...