Whirlpool ADP 6637 IX, ADP 6637, ADP 6637 BR, ADP6637AL INSTRUCTION FOR USE

How to use the appliance

ABC

Further indications are given in the single chapters and in the user instructions.

Switch on the appliance

Select, save, and

supply the detergent

Check the rinse aid level

Check the

regeneration salt level

Load the racks

Press the ON / OFF button.

(The first time you use the appliance and when using a different type of detergent)

1. Select the third programme from the top in the relative table.

2. Press the Start button for about 7 seconds until the display changes.

3. Select the required detergent with the Start button (OFF = powder detergent, 2 in 1, 3 in 1, 4 in 1) (shown on the display).

4. Switch the appliance off and then switch it on again. The selected detergent type will be shown on the display for approximately 3 seconds after switching on.

For dosage of powder detergent in compartment A and B refer to the programmes table.

Mechanical indicator C. Electric indicator on control panel (if provided).

On models with water softener system only.

Mechanical indicator D. Electric indicator on control panel (if provided).

Refer to the dishwasher loading instructions.

Close the dishwasher door,

turn on the water tap

Select a programme

Select additional options

Press the Start button

Wash cycle

Switch off the appliance

Turn off the water tap,

unload the racks

The last programme selected will light up. Select the desired programme (using the specific button or knob). The corresponding indicator lamp lights up.

If necessary (and if provided). The corresponding indicator lamp lights up.

The selected programme is then memorised (even in the event of power failure).

Only after the START button has switched off: Press the ON / All the indicator lamps switch off.

Warning: When the door is opened steam comes out!

Unload the appliance, starting from the lower rack.

“Change programme in progress”

Press the START button for 2 sec. until the Start indicator lamp switches off.

Select another programme and press the START button again.

- Only open the dishwasher if necessary (Warning: beware of hot steam).

- If the appliance is switched off during a wash cycle, when switched on again it will resume the cycle from where it was interrupted.

OFF

button.

Dishwasher loading instructions and racks provided

depending on the model

Upper rack:

Crockery holder (A):

Depending on the position, for long-handles utensils, cups and plates.

Glass holder (B):

Long-stemmed glasses.

Long-handled utensils (e.g. carving forks, knives) must be arranged with the sharp end facing in towards the appliance.

Half Load:

Load the upper rack (see description of Options). Place the cutlery basket (C), if provided, in the upper rack.

Rack height adjustment (also when loaded):

Pull the

Lower adjustment:

Upper adjustment:

The rack must be level on both sides.

Removing the top rack to provide clearance for large items of crockery in the bottom rack:

Open the rack guide retainers (E) on the right and left and remove the top rack. When the upper rack is in place the retainers must always be closed.

(D) outwards and lower the rack.

Pull the (D) upwards until the rack clicks into place (factory setting).

rack handles

two

rack handles

two

Retainer

open

Retainer

closed

Lower rack:

Depending on the model with fixed or tilting plate holders (F).

Half Load:

Load the lower rack (see description of Options).

Greater washing power, particularly for plates and saucepans.

Cutlery basket (G):

Grid (H) to keep items separate.

Sharp knives and forks that might cause injury must be placed in the cutlery basket with the sharp end facing downwards.

Only use dishwasher-proof crockery and dishes. Do not use the appliance for items not suitable for washing in a dishwasher, for example wooden items, aluminium, tin, hand-decorated crockery (unglazed), silver cutlery.

+ 2 hidden pages