WHIRLPOOL ADP 6332/1 WH User Manual

(see at right for options

description)

START/RESUME BUTTON Push this button to start the selected program: the indicator lights up and goes off at the end of the program. When the door is opened during a washing cycle, the cycle is temporarily paused: the Start indicator blinks. To resume the cycle close the door and push Start button again.

PROGRAM SELECTION BUTTON Push “Programs” button (repeatedly) until the indicator of the required program lights up (see “Table of programs” below).

CANCEL/OFF BUTTON Push this button to switch off the control panel. If pressed when a program is running it cancels the program ongoing draining water for 1 minute. If pressed when the dishwasher is switched off it drains any possible liquids from dishwasher (1 minute process). If the indicator flashes repeatedly, see page 6 chapter “What to do if...”.

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/ Standard loading comparison test and other tests, contact the following address: “contact@whirlpool.com”.

* Power consumption in: Left-on mode: 0.70 W / Off mode: 0.40 W.

Table of programs

Deter-

gent

Consumption

Drying

Phase

Programs

Available

options

Loading instructions

Litres kWh

Minutes

Pre-Wash cold

Delay Crockery to be washed later. — 4.0 0.01 14-16 NO

Fragile 40°C

Delay

Light soiling, for example glasses and cups.

X 10.5 0.85 105-114 Light

Rapid 45°C

Delay

Lightly soiled crockery, with no dried-on food.

X 11.0 0.85 30-50 NO

Eco

50°C

Delay

Normally soiled crockery. Standard program the most efficient in terms of its combined energy and water consumption.

X 12.0 1.02 155 Full

Intensive 65°C

Delay

Recommended program for heavily soiled crockery, especially suitable for pans and saucepans.

X 15.0 1.60 165-175 Full

5019 300 01284

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS

QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTR UCTIONS!

Options and display description

SALT INDICATOR When lit (at the end of the

cycle), the salt reservoir needs to be refilled.

DELAYED START BUTTON The wash cycle can be programmed to start after 2, 4 or 8 hours. Then press the Start button. The wash program will start after the set time.

RINSE AID INDICATOR When lit (at the end of the

cycle), the rinse aid dispenser needs to be refilled.

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY

BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVA TES

AUTOMATICALLY AFTER 30 SECONDS IF NO CY CLE HAS STARTED.

TABLET SETTING This setting allows to optimize the cycle pe rformances according the type of detergent used. Push the Tablet button for 3 seconds (until the indicator lights up) if you are using the combined detergents in tablet (rinse aid, salt and detergent in 1 dose). If you are using powder deterge nt or liqui d deterge nt, the Tablet indicator on the control panel has to be off.

Quick reference guide

Chart

Whirlpool is a registered trademark of Whirlpool USA

EN -1-

1- salt reservoir 2- rinse aid dispenser 3- detergent dispenser 4- racks system 5,6,7,8- available functions on the panel 9- filters 10- spray arms

1. Ask your water supply company what the water hardness is... 2. ...enter this value on

your dishwasher

Suggestions for detergent use

German

degrees °dH

French

degrees °fH

English

degrees °eH

Water hardness

level

3 first PROGRAM LEDs

lit on the panel

(see table of programs)

P1 P2 P3

Gel or Powder

(rinse aid and

salt)

Tablets

0 - 5 0 - 9 0 - 6.3 Soft 1

go to step 1

(see “Daily

check”)

6 - 10 10 - 18 7 - 12.6 Medium 2 11 - 15 19 - 27 13.3 - 18.9 Average 3 16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4

if water is

HARD extra salt

needs to be

added

(go to step1,

“Daily check”)

22 - 28 38 - 50 26.6 - 35 Hard 5 29 - 35 51 - 63 35.7 - 44.1 Very hard 6 36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7

Water hardness should be set only

before the first wash or if water

hardness has been changed

Visual indicator (depending on the model). Unscrew cap.

Fill the salt reservoir with water

before the first wash only .

(depending on the model)

The salt level indicator lamp may rem ai n lit at the end of several wash cycles. If the water hardness level falls with in category (soft), no salt is required.

Salt indicator on the control pa ne l Salt indicator on the salt reservoir cap

The indicator lamp lights up when SALT NEEDS TO BE ADDED.

green: OK.

clear: NEEDS TO

BE ADDED

Daily check

Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)

- Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds.

- Programs LEDs will indicate the water hardness setting.

- Press the Programs button to increase setting (when the level reaches 7, the next key press will set the level back to 1.

- Wait 30 seconds (control panel switches off) or press START/Resume button to save setting.

Add salt (never add detergent!)

min. 0.8 kg / max. 1 kg

Water hardness level is factory set for medium-hard water (level 4).

Even if you use tablets which include salt functionality, you must still add regeneration salt since such detergents are not effective enough at softening hard water.

At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).

Screw on the cap. Salt residual around the cap need to be removed. Some salt reservoir have a level indicator integrated in the cap (see below how to check).

Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient). Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components. The guarantee is not applicable if faults are caused by such circumstances.

How to set water hardness in order to always assure the best cleaning results

First time use

EN -2-

Check the rinse aid indicator to check the level into the dispenser.

(depending on the model) Rinse aid indicator on the control panel Rinse aid indicator on the dispenser

The indicator lamp lights up when RINS E AID NEEDS TO BE ADDED.

dark: OK. clear: NEEDS TO BE ADDED

Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.

If there are streaks: reduce the dosage by turning t he dial to a lower setti ng (1-3). If crockery is not perfectly dry: increase th e dosage by turning the dial to a higher setting (5- 6). Plastic di shes have more diff iculty drying and a higher rinse aid setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.

Daily use

Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations

Open the cover A

(press the dedicated button).

Only fill the detergent dispenser prior to starting a wash program.

Shut the cover

by pressing dedicated ribs.

Insert detergent: Tablet / powder / liquid into the big chamber.

Please look for the recommendation of the detergent manufacturer

on the packaging of the detergent product.

Use only one tablet per one cycle, only placed in detergent dispenser.

All types of tablets can be used, but for 2 in 1 type adding of salt is mandatory.

Some types of tablets may not dissolve completely during the short cycles (Rapid, Fragile, H an dwash); placing the tablet on the tub bottom can help dissolving and washing.

If required, open the cover B (press the dedicated button).

Add rinse aid to the max. line ~150 ml

The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.

Visual indicator

Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator

Daily check

EN -3-

+ 5 hidden pages