Whirlpool ADP 5655 WH INSTRUCTION FOR USE
w
Quick reference guide
Chart
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULL Y READ
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
(see at right for options description)
PROGRAM SELECTION
BUTTON
Push “Programs” button
(repeatedly) until the indicator
of the required program lights
up (see “Table of programs”
below).
START/RESUME BUTTON
Push this button to start the selected program: the
indicator lights up and goes off at the end of the
program.
When the door is opened during a washing cycle,
the cycle is temporarily paused: the Start indicator
blinks. To resume the cycle close the door and
push Start button again.
Table of programs
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute (0:01
is shown into the display).
If pressed when the dishwasher is switched off, it
drains any possible liquids from dishwasher
(1minute process).
Consumption
Deter-
gent
Litres kWh
X 7-14 1.00-1.60 70-155
X 11.0 0.80 30
X 14.0 1.55 155
Minutes
50°C
Available
options
Delay
Antibacterial
rinse
Delay Crockery to be washed later. — 4.0 0.03 14
Delay
Delay
Antibacterial
rinse
Delay
Antibacterial
rinse
Loading instructions
Recommended program for
routine washes, with dried-on
food (e.g. EN 50242).
Lightly soiled crockery, with no
dried-on food.
Normally soiled crockery. X 13.0 0.93 185
Recommended program for
heavily soiled crockery, especially
suitable for pans and saucepans.
P
1
2
3
4
5
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional
options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the
appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for T esting Institutes: for detailed information on the
EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
Programs
Auto Sensor 50-65°C
Pre-Wash cold
Quickwash 45°C
2)
Eco
Intensive 70°C
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
AUTOMATICALLY AFTER 30 SECONDS IF ANY CYCLE IS STARTED.
Options and display description
SALT INDICATOR
When lit (at the end of the cycle),
the salt reservoir needs to be
refilled.
WASH TIME DISPLAY
Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates
the time remaining until program start (h.00) - below 1h (0:mim).
If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.
ANTIBACTERIAL RINSE
This function activates an
1)
antibacterial rinse at the end of
the wash cycle, guaranteeing a
further reduction of bacteria.
Press the button to activate or
deactivate the function. This
function can be used with the
programs indicated in the table
of programs. The dishwasher
door must be kept shut for the
entire duration of the program in
order to guarantee reduction of
bacteria. If the door is opened
the indicator lamp starts flashing.
TABLET SETTING
This setting allows to optimize the cycle performances
according the type of detergent used.
Push the Tablet button for 3 seconds (until the indicator lights
up) if you are using the combined detergents in tablet (rinse aid,
salt and detergent in 1 dose).
If you are using powder detergent or liquid detergent, the
Tablet indicator on the control panel has to be off.
3)
RINSE AID INDICATOR
When lit (at the end of the cycle),
the rinse aid dispenser needs to
be refilled.
DELAYED ST ART BUTTON
Push the button (repeatedly)
to delay the start of the
program. Adjustable from 1 to
24 hours. With each press of
the button, the delayed start
indicator increases by one
hour and after 24 restarts from
0. Then press the START
button. The dishwasher will
start after the set time.
5019 396 01832/BADP 5655
GB
-1-
How to set water hardness in order to always assure the best cleaning results
First time use
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
Water hardness should be set only
before the first wash or if water
hardness has been changed
1.
Ask your water supply company what the
German
degrees °dH
0 - 5 0 - 9 0 - 6.3 Soft 1
6 - 10 10 - 18 7 - 12.6 Medium 2
11 - 15 19 - 27 13.3 - 18.9 Average 3
16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4
22 - 28 38 - 50 26.6 - 35 Hard 5
29 - 35 51 - 63 35.7 - 44.1 Very hard 6
36 - 60 64 - 107 44.8 - 74.9 Extremely hard 7
Filling the salt reservoir -
1
French
degrees °fH
At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).
English
degrees °eH
Dissolve limescale (not necessary if water hardness level is set to “soft”!)
Visual indicator
(depending
on the model).
Unscrew cap.
The salt level indicator lamp may remain lit
at the end of several wash cycles. If the
water hardness level falls within category
(soft), no salt is required.
- Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds.
- The current water hardness setting will be visible on the display.
-Press the Programs button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of
the start button will set the level back to 1).
- Wait 30 seconds (control panel switches off) or press Start/Resume button to save setting.
water hardness
is...
Water hardness
level
Fill the salt reservoir with water
before the first wash only.
(depending on the model)
Salt indicator on the control panel Salt indicator on the salt reservoir cap
2.
...enter this value on
your dishwasher
Insert value is shown
in the display
The indicator lamp lights up when SALT
NEEDS TO BE ADDED.
Gel or Powder
(rinse aid and salt)
go to step 1
(see “Daily
Add salt (never add detergent!)
Suggestions for detergent use
Tablets
check”)
min. 1.5 kg / max. 2 kg
if water is
HARD extra salt
needs to be added
(go to step 1,
“Daily check”)
Water hardness level is
factory set for medium-hard
water (level 4).
Even if you use tablets which
include salt functionality, you
must still add regeneration
salt since such detergents are
not effective enough at
softening hard water.
Daily check
orange:
OK.
Screw on the cap.
Salt residual
around the cap
need to be
removed. Some
salt reservoir have
a level indicator
integrated in the
cap (see below
how to check).
clear: NEEDS TO
BE ADDED
GB
-2-
Adding rinse aid
(not necessary when you use tablets). How to adjust the rinse aid dosage regulator
Daily check
Visual
2
Check the rinse aid indicator to check the level
into the dispenser.
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the
appliance.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty
drying and a higher rinse aid setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with
rinse aid incorporated tend to form excess suds.
Adding detergent -
(press the dedicated button).
Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Open the cover A
3
indicator
If required,
open the
cover B
(press the
dedicated
button).
Add rinse aid
to the max.
line ~150 ml
(depending on the model)
Rinse aid indicator on the control panel Rinse aid indicator on the dispenser
The indicator lamp lights up when RINSE AID NEEDS
TO BE ADDED.
Insert detergent: Tablet / powder / liquid into the big chamber
Only fill the
detergent dispenser
prior to starting a
wash program.
The rinse aid dosage can be
adjusted to the detergent used.
The lower the setting, the less
rinse aid is dispensed (factory
setting: position 4).
Press the button to open the
cover B. Using a coin or similar
object, turn the arrow to the
desired setting. After adjusting
the rinse aid setting, shut the
cover again.
dark: OK. clear: NEEDS TO BE ADDED
Shut the cover
by pressing dedicated ribs.
Use only one tablet per one cycle, only
placed in detergent dispenser.
All types of tablets can be used, but for
2 in 1 type adding of salt is mandatory.
Daily use
GB
-3-
Loading...