Quick reference guide |
Chart |
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
|
(see at right for options description) |
|
PROGRAM SELECTION |
START/RESUME BUTTON |
CANCEL/OFF BUTTON |
BUTTON |
Push this button to start the selected program: the |
Push this button to switch off the control panel. |
Push “Programs” button |
indicator lights up and goes off at the end of the |
If pressed when a program is running it cancels the |
(repeatedly) until the indicator |
program. When the door is opened during a |
program ongoing draining water for 1 minute. |
of the required program lights |
washing cycle, the cycle is temporarely paused: the |
If pressed when the dishwasher is switched off it |
up (see “Table of programs” |
Start indicator blinking. To restart the cycle close |
drains any possible liquids from dishwasher (1 |
below). |
the door and push Start button again. |
minute process). |
|
|
If the indicator flashes repeatedly, see page 6 - |
|
|
chapter ”What to do if ...”. |
|
|
Table of programs |
|
Consumption |
|
|
|
|
Deter- |
P |
Programs |
Available |
Loading instructions |
gent Litres kWh Minutes 1) |
|
|
options |
|
|
|
|
|
|
|
1
2
3
4
5
AutoSensor |
50-65°C |
Delay |
Recommended program for routine |
|
Power Clean |
washes, with dried-on food (e.g. EN 50242). |
|||
Quickwash |
45°C |
Delay |
Lightly soiled crockery, with no dried- |
|
on food. |
||||
|
|
|
||
Eco 2) |
50°C |
Delay |
Normally soiled crockery. |
|
Power Clean |
Antibacterial 3) |
|
Delay |
|
|
Power Clean |
||
Intensive |
70°C |
|
Delay |
|
|||
|
Power Clean |
||
|
|
|
|
|
|
|
|
Normally or heavily soiled crockery, with additional antibacterial wash. Program interruption (e.g. due to door opening) can compromise elimination of germs.
Recommended program for heavily soiled crockery, especially suitable for pans and saucepans.
X |
7-14 1.00-1.60 |
70-155 |
||
X |
11.0 |
0.80 |
30 |
|
X |
12.0 |
1.05 |
150 |
|
X |
13.0 |
1.50 |
115 |
|
X |
|
1.55 |
|
155 |
14.0 |
|
|||
|
|
|
|
|
1)Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.
2)Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
3)The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF ANY CYCLE IS STARTED.
Options and display description
SALT INDICATOR
When lit (at the end of the cycle), the salt reservoir needs to be refilled.
POWER CLEAN
Thanks to the additional power jets this option provides a more intensive and powerful wash in the lower rack, in the specific area. This option is recommended for washing pots and casseroles (see page 4). Press this button to activate Power Clean (the indicator lights up).
TABLET SETTING
This setting allows to optimize the cycle performances according the type of detergent used.
Push the Tablet button for 3 seconds (until the indicator lights up) if you are using the combined detergents in
tablet (rinse aid, salt and deteregent in 1 dose).
If you are using powder detergent or liquid detergent, the Tablet indicator on the control panel has to be off.
RINSE AID INDICATOR
When lit (at the end of the cycle), the rinse aid dispenser needs to be refilled.
DELAYED START BUTTON
The wash cycle can be programmed to start after 2, 4 or 8 hours. Then press the Start button. The wash program will start after the set time.
ADP 5600 PC |
5019 396 01839/B |
GB -1-
How to set water hardness in order to always assure the best cleaning results |
First time use |
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10spray arms
Water hardness should be set only - Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds. |
||
before the first wash or if water |
- Programs LEDs will indicate the water hardness setting. |
|
hardness has been changed |
||
- Press the Programs button to increase setting (when the level reaches 7, the next key press will set the level back to 1. |
||
|
||
|
- Wait 30 seconds (control panel switches off) or press START/Resume button to save setting. |
|
1. Ask your water supply company what the water hardness is... |
|
2. ...enter this value on |
Suggestions for detergent use |
||||||||
|
|
|
|
|
|
|
your dishwasher |
|
|||
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
3 first PROGRAM LEDs |
Gel or Powder |
|
||
German |
French |
English |
Water hardness |
|
lit on the panel |
|
|||||
|
(rinse aid and |
Tablets |
|||||||||
degrees °dH |
degrees °fH |
degrees °eH |
level |
|
(see table of programs) |
||||||
|
salt) |
|
|||||||||
|
|
|
|
|
|
|
P1 |
P2 |
P3 |
|
|
|
|
|
|
|
|
|
|
|
|||
0 |
- 5 |
0 |
- 9 |
0 - 6.3 |
Soft |
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6 - 10 |
10 |
- 18 |
7 - 12.6 |
Medium |
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
11 |
- 15 |
19 |
- 27 |
13.3 - 18.9 |
Average |
3 |
|
|
|
go to step 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
16 |
- 21 |
28 |
- 37 |
19.6 - 25.9 |
Medium-hard |
4 |
|
|
|
(see “Daily |
if water is |
|
|
|
|
|
|
|
|
|
|
check”) |
HARD extra salt |
22 |
- 28 |
38 |
- 50 |
26.6 - 35 |
Hard |
5 |
|
|
|
||
|
|
|
|
needs to be |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
29 |
- 35 |
51 |
- 63 |
35.7 - 44.1 |
Very hard |
6 |
|
|
|
|
added |
|
|
|
|
(go to step 1, |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
36 |
- 60 |
64 - 107 |
44.8 - 74.9 |
Extremely hard |
7 |
|
|
|
|
||
|
|
|
|
“Daily check”) |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
Water hardness level is factory set for medium-hard water (level 4).
Even if you use tablets which include salt functionality, you must still add regeneration salt since such detergents are not effective enough at softening hard water.
At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!) |
Daily check |
1 |
Visual indicator |
(depending |
|
on the model). |
|
|
Unscrew cap. |
Fill the salt reservoir with water |
Add salt (never add detergent!) |
before the first wash only. |
min. 1.5 kg / max. 2 kg |
Screw on the cap. Salt residual around the cap need to be removed. Some salt reservoir have a level indicator integrated in the cap (see below how to check).
|
(depending on the model) |
|
|
|
The salt level indicator lamp may remain lit Salt indicator on the control panel |
Salt indicator on the salt reservoir cap |
|||
at the end of several wash cycles. If the |
The indicator lamp lights up when SALT |
orange: |
clear: NEEDS TO |
|
water hardness level falls within category |
||||
NEEDS TO BE ADDED. |
OK. |
BE ADDED |
||
(soft), no salt is required. |
||||
|
|
|
||
GB -2-
Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator
Daily check
2 |
Visual |
|
|
|
indicator |
If required, open the cover B (press the dedicated button).
Add rinse aid to the max. line ~150 ml
The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4).
Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.
Check the rinse aid indicator to check the level into the dispenser.
(depending on the model)
Rinse aid indicator on the control panel
The indicator lamp lights up when RINSE AID NEEDS TO BE ADDED.
Rinse aid indicator on the dispenser
dark: OK. |
clear: NEEDS TO BE ADDED |
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.
Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Daily use
Open the cover A |
Insert detergent: Tablet / powder / liquid into the big chamber |
Shut the cover |
|
(press the dedicated button). |
|
|
by pressing dedicated ribs. |
3 |
Only fill the |
Use only one tablet per one cycle, only |
|
detergent dispenser |
placed in detergent dispenser. |
|
|
|
prior to starting a |
|
|
|
wash program. |
All types of tablets can be used, but for |
|
|
|
2 in 1 type adding of salt is mandatory. |
|
GB -3-
Loading...