Whirlpool ADP410WH User Manual

(see at right for options description)

PROGRAMS SELECTION BUTTON Push “P” button (repeatedly) until selected program number is shown on the display (P1...Px) - see “Table of programs” below.

CANCEL/OFF BUTTON Push this button to switch off the control panel. If pressed when a program is running it cancels the program ongoing draining water for 1 minute (0:01 is shown into the display). If pressed when the dishwasher is switched off, it drains any possible liquids from dishwasher (1 minute process).

START/RESUME BUTTON Push this button to start the selected program: the indicator lights up and goes off at the end of the program. When the door is opened during a washing cycle, the cycle is temporarily paused: the Start indicator blinks. To resume the cycle close the door and push Start button again.

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “contact@whirlpool.com”.

*Power consumption in Left-on mode: 1.27 W / Off-m ode: 0.40 W

Table of programs

Deter-

gent

Consumption

Drying

Phase

Programs

Available

options

Loading instructions

Litres kWh

Minutes

Sensor 40-70°C

Delay

Hygiene

1/2 Load

Recommended program for routine washes, with dried-on food.

X 7-15 1.00.1.70 70-172 Full

Pre-Wash cold

Delay Crockery to be washed later. — 4.0 0.01 14-16 NO

Rapid 45°C

Delay

Lightly soiled crockery, with no driedon food.

X 11.0 0.85 30-50 NO

Eco

50°C

Delay

Hygiene

1/2 Load

Normally soiled crockery. Standard program, the most efficient in terms of its combined energy and water consumption.

X 10.0 0.92 230 Full

Daily 60°C

Delay

Hygiene

1/2 Load

Normally to heavily soiled crockery. X 11.0 1.30 80-95 Full

Steam

Delay

Hygiene

Program including steam action dedicated for heavily soiled crocery, pots and pans. Soaking or hand pretreatment is no longer needed.

X 14.5 1.75 180-190 Full

5019 300 02699

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS

QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTR UCTIONS!

Options and display description

SALT INDICATOR When lit (at the end of the cycle), the salt reservoir needs to be

refilled.

RINSE AID INDICATOR When lit (at the end of the cycle), the rinse aid dispenser needs to

be refilled.

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY

BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVA TES

AUTOMATICALLY AFTER 30 SECONDS IF NO CY CLE HAS STARTED.

1/2 LOAD BUTTON Half load cycle can be used for the upper or lower rack. Select the required program then press the “Half Load” button - the light comes on. Turns off at the end of the program. The ˝Half Load˛ option can be used with the programs indicated in the table of programs.

TABLET SETTING This setting allows to optimize the cycle performances according the type of detergent used. Push the Tablet button for 3 seconds (until the indicator lights up) if you are using the combined detergents in tablet (rinse aid, salt and detergent in 1 dose). If you are using powder detergent or gel detergent, the Tablet indicator on the control panel has to be off.

DELAYED START BUTTON Push the button (repeatedly) to delay the start of the program – delay indicator turns on. Adjustable from 1 to 24 hours. With each press of the button, the delay increases by one hour and after "h 24" returns to "h 00”. When this option is selected the delay indicator turns on. Then press the START button. The dishwasher will start after the set time.

HYGIENE This function activates an antibacterial rinse at the end of the wash cycle, guaranteeing a further reduction of bacteria. Press the button to activate or deactivate the function. This function can be used with the programs indicated in the table of programs. The dishwasher door must be kept shut for the entire duration of the program in order to guarantee reduction of bacteria. If the door is opened the indicator lamp starts flashing.

WASH TIME DISPLAY Indicated the cycle

duration and the remaining time (h:min). With “Delayed start” selected it indicates the time remaining until program start (h.00) below 1h (0:min). If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.

Quick reference guide

Chart

Whirlpool is a registered trademark of Whirlpool USA

EN -1-

1- salt reservoir 2- rinse aid dispenser 3- detergent dispenser 4- racks system 5,6,7,8- available functions on the panel 9- filters 10- spray arms

Water hardness should be set

before the first wash or if water

hardness has been changed

Visual indicator (depending on the model). Unscrew cap.

Fill the salt reservoir with water

before the first wash only.

(depending on the model)

The salt level indicator lamp may remain lit at the end of several wash cycles. If the water hardness is set to level 1 (soft), no salt is required and salt indicator lamp will remain off.

Salt indicator on the control panel Salt indicator on the salt reservoir cap

The indicator lamp lights up when SALT NEEDS TO BE ADDED.

green: OK.

clear: NEEDS TO BE ADDED

Daily check

Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft 1”!)

Screw on the cap. Salt residual around the cap needs to be removed. Some salt reservoirs have a level indicator integrated in the cap (see below how to check).

- Press and hold together Program and buttons for minimum 3 seconds.

- The current water hardness setting will be visible on the display.

-Press the Program button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of the start button will set the level back to 1).

- Wait 30 seconds (control panel switches off) or press Start/

Pause

button to save setting.

1. Ask your water supply company what the water hardness is... 2. ...enter this value

on your dishwasher

Salt required

German

degrees °dH

French

degrees °fH

English

degrees °eH

Water hardness

level

Insert value is shown

in the display

0 - 5 0 - 9 0 - 6.3 Soft 1 NO

6 - 10 10 - 18 7 - 12.6 Medium 2

YES

11 - 15 19 - 27 13.3 - 18.9 Average 3 16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4 22 - 28 38 - 50 26.6 - 35 Hard 5 29 - 35 51 - 63 35.7 - 44.1 Very hard 6 36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7

Add salt (never add detergent!)

min. 0.8 kg/max. 1 kg

Water hardness level is factory set for medium-hard water (level 4).

Detergents

When powder or gel detergent is used, regeneration salt must be added and water hardness level must be set as indicated in the table on the right.

Also, when tablets which include salt functionality are used, regeneration salt still must be added.

Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient). Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components. The guarantee is not applicable if faults are caused by such circumstances.

How to set water hardness in order to always assure the best cleaning results

First time use

Before first use, run the appliance with detergent and without loading.

EN -2-

Check the rinse aid indicator to check the level into the dispenser.

(depending on the model) Rinse aid indicator on the control panel Rinse aid indicator on the dispenser

The indicator lamp lights up when RINS E AID NEEDS TO BE ADDED.

dark: OK. clear: NEEDS TO BE ADDED

Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.

If there are streaks: reduce the dosage by turning t he dial to a lower setti ng (1-3). If crockery is not perfectly dry: increase th e dosage by turning the dial to a higher setting (5- 6). Plastic di shes have more diff iculty drying and a higher rinse aid setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.

Daily use

Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations

Open the cover A

(press the dedicated button).

Only fill the detergent dispenser prior to starting a wash program.

Shut the cover

by pressing dedicated ribs.

If required, open the cover B (press the dedicated button).

Add rinse aid to the max. line ~150 ml

The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.

Visual indicator

Use only one tablet per one cycle, only placed in detergent dispenser.

Some type of tablets could not dissolve completely during the short programs (Rapid, Fragile, Handwash); pl aci ng the tablet on the tub bottom can help dissolving and washing.

Insert detergent: Tablet / powder / gel into the big chamber.

Please look for the recommendation of the detergent manufacturer

on the packaging of the detergent product.

Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator

Daily check

EN -3-

+ 5 hidden pages