Whirlpool ADG 953-1 S Service Manual
SERVICE
Model ADG 953/1 S
Version 8542 953 38110 Page
Whirlpool Europe
Customer Services
ADG 953/1 S
Service Manual
Dishwasher
integratable
ADG 953/1 S
Technical data 2 - 3
Spare part list 4 - 5
Exploded view 6 - 7
Circuit diagram 8
Program diagram 9
Text/Legend 10 - 18
Family A5
This documentation is only intended for qualified technicians who are aware of the respective safety regulations.
Date: 03.11.1997 Subject to modification
Document-No.: 4812 718 12552
03.11.1997 / Page 2 ADG 953/1 S Whirlpool Europe
Doc. No: 4812 718 12552 8542 953 38110 Customer Service
Technical data
SERVICE
Dimension
Height 82,0-87,0 cm
Width 59,5 cm
Depth 57,0 cm
Weight 55,0 kg
Wooden door (for 22 mm thickness)
Thickness min.. 16 mm
Thickness max. 25 mm
Width min. 592 mm
Width max. 595 mm
Height min. 628 mm
Height max. 718 mm
Weight min. 2,5 kg
Weight max. 6,5 kg
Max. stick out over lower
edge of appliance door 90 mm
Height of plinth min. 93 mm
Specification (normal program)
Measuring the level
Remove the coarse sieve, put in a measuring
meter into the sump, measure the hight of the
water level.
Detergent max.
Pre-wash 10 cm
Main-wash 45 cm
Rinse aid 125 cm
6 Dosage steps 1 - 6 ml
Water softener
Saltcontainer 2 kg
Resin container 900 cm
Regeneration dosage 300 cm
Water pressure
Inlet pressure 0,3-10 bar
Spray pump pressure 0,4 bar
3
3
3
3
3
Capacity 12 standard
setting pl.
Water consumption 19 l
Energy consumption 1,4 kWh
Program time ~ 78 min
Noise level 49 db (A)
Detergent consumption 25 ml
Salt consumption
by 21˚ dh <20 g
Hot water connect. up to 60 ˚C
Alarms
Refill salt
Program information (acoustic)
End
Volume (normal program)
Water Volume Level
Regeneration 0,3 l 15 mm
Back rinse 3x 1,0 l 68 mm
Prewash 5,0 l 125 mm
Main wash 5,0 l 125 mm
Intermediate rinse 1 4,5 l 123 mm
Intermediate rinse 2 4,5 l 123 mm
Intermediate rinse 2/
Zone washing 3,8 l 119 mm
Clear rinse 4,5 l 123 mm
Safety / overflow 8,5 l 141 mm
Rotations
Spray pump motor 2800 RPM
Drain pump motor 2800 RPM
Spray arm lower ~ 30 RPM
Spray arm upper ~ 35 RPM
Ceiling rotor ~ 60 RPM
Flow rates / Inlet volume
Flow meter (at 0,3 bar
= quantity 1,1 l/min) 208 lmp/l
Spray pump ~ 70 l/min
Drain pump 16 l/min
Pump height max. 1,3 m
Inlet valve 4,5 l/min
Spray arm lower 33 l/min
Sprayarm upper 30 l/min
Ceiling rotor 8 l/min
Water distribution
Fine sieve 100 %
Micro filter ~ 30 %
SERVICE
Technical data
Whirlpool Europe ADG 953/1 S 03.11.1997 / Page 3
Customer Service 8542 953 38110 Doc. No: 4812 718 12552
Electrical data
Base data
Voltage 230 V
Frequency 50 Hz
Total power ~ 2,5 kW
Fuse 13 A
Motor
Spray pump motor
Voltage 220/230 V
Power consumption ~190 W
HI 69 Ω
HA 36,2 Ω
Capacitor 4 µ F
Drain pump motor
Voltage 220/240 V
Resistance 146 Ω
Heating
Regenerating valve
Voltage 220/240 V
Frequency 50/60 Hz
Resistance 3,13 kΩ
Coil of dispenser
Voltage 220/240 V
Frequency 50/60 Hz
Resistance 1,43 kΩ
Relay
Heating relay
Voltage 220/240 V
Frequency 50/60 Hz
Resistance 5,5 kΩ
Reedcontact
flow meter
salt control
1 Element system
Voltage 230 V
Power consumption 2350 W
Resistance 18,66 Ω
Heating speed ~ 2,5 ˚C/min
Temperature on surface ~ 115 ˚C
Double safety thermostat
self reset 85 ˚C
Potentiometer
Position 0 2,0 kΩ
Position 1 4,3 kΩ
Position 2 9,0 kΩ
Position 3 13,3 kΩ
Position 4 17,5 kΩ
Position 5 22,2 kΩ
Position 6 24,2 kΩ
Water valves
NTC
15 ˚C 75 kΩ
20 ˚C 62 kΩ
30 ˚C 43 kΩ
40 ˚C 28 kΩ
50 ˚C 19 kΩ
60 ˚C 13 kΩ
70 ˚C 9 kΩ
80 ˚C 6 kΩ
85 ˚C 5 kΩ
Regeneration
Volume 300 cm
Position 0
after wash cycles 1
water hardness 0-60 ˚dh
0-10,7 mmol/l
0-107 ˚Fh
3
Single valve
Voltage 220/240 V
Frequency 50/60 Hz
Resistance 2,06 kΩ
Salt consumption
for regeneration 77 g
Number of cycles
with 2 kg salt 26
03.11.1997 / Page 4 Whirlpool Europe
Doc. No: 4812 718 12552 Customer Service
Spare part list
Model ADG 953/1 S
Service No. 854295338110
Version 854295338110
SERVICE
Pos. No. 12NC Code Description
003 0 4812 440 19382 Traverse
004 0 4812 440 18952 Drip tray assy
004 1 4812 401 18402 Holder
011 0 4812 505 18369 Foot long
011 1 4812 528 98002 Shaft flexible
011 2 4812 528 78032 Slide disc f.foot
011 3 4812 535 98048 Gear
011 4 4812 528 98001 Roll f.foot
022 0 4812 440 19398 Side panel left
022 1 4812 440 19397 Side panel right
022 2 4812 440 18953 Spacer
024 0 4812 440 18948 Panel, rear to 97/07
024 0 4812 440 19401 Panel, rear from 97/07
040 1 4812 417 18774 Hinge left
040 2 4812 417 18773 Hinge right
044 0 4812 492 38362 Spring f.door
047 0 4812 404 48591 Brake f.door
047 1 4812 401 18397 Band,brake
047 2 4812 404 68023 Hook
053 0 4812 440 88875 Plinth
103 0 4812 440 18986 Door outer
105 0 4812 404 48611 Fastener door
105 2 4812 505 68004 Clip
105 3 4812 404 48633 Fastener
120 0 4812 440 18961 Door,inner
Pos. No. 12NC Code Description
450 0 4812 259 28655 Heating element
480 0 4812 321 28364 Cable harness set
480 1 4812 321 28371 Cable
480 3 4812 401 18418 Protector f.wiring
480 4 4812 401 18419 Cover of cable from 97/07
490 0 4812 321 18026 Cable,mains 3m to 97/07
490 0 4819 321 18136 Cable,mains 2m from 97/07
490 1 4812 321 28367 Strain relief from 97/07
521 0 4812 214 78172 Control board (CB)
571 0 4812 281 28379 Valve inlet
575 0 4812 281 28361 Regen.valve
583 0 4812 271 28355 Switch diaphragm
612 0 4812 280 58025 Relay heating
616 0 4812 281 18047 Contact,reed salt
620 0 4812 218 38041 User board (UCB)
623 0 4812 271 38356 Microswitch
633 0 4812 271 38355 Microswitch
680 0 4812 418 68133 Combidosage
680 1 4812 466 68495 Gasket
681 1 4812 466 68497 Gasket
681 2 4812 440 18975 Flap
682 0 4812 466 68496 Gasket
691 0 4812 282 68012 Feeler NTC
701 0 4812 530 28081 Hose, inlet 3/8Z cpl. 5m
701 0 4812 530 28082 Hose, inlet 3/8Z cpl. 3m
120 1 4812 440 18955 Batten
130 0 4812 417 58361 Tilt lock
131 0 4812 401 18416 Hook lock
175 3 4812 466 68532 Batten
191 0 4812 466 68534 Gasket door
192 0 4812 466 68467 Gasket, door lower
200 0 4812 418 18183 Container cpl.
241 0 4812 458 18273 Basket upper straight
241 1 4812 458 18324 Holder cups rigth white
241 3 4812 528 88068 Wheel,basket upper (set)
241 8 4812 466 68482 Spacer cap set
241 9 4812 528 88075 Wheel,basket basket upper
242 0 4812 458 18271 Basket lower cpl.
242 1 4812 528 88069 Wheel,basket lower
243 0 4812 458 18272 Basket cutlery
261 0 4819 462 38271 Rail telescope, inner
261 1 4819 404 48819 Cap rail
261 2 4812 462 78995 Cap rail ahead
263 0 4819 520 18013 Ball cage cpl.
263 1 4812 520 48001 Ball Niro 8 D
301 0 4812 453 79762 Control panel WH
322 0 4812 453 79885 Insert panel cpl.
332 5 4812 410 28556 Cap f.beater
400 0 4812 361 58119 Motor + spraypump cpl.220/240V
405 0 4812 360 18358 Spray pump
701 0 4819 530 28283 Hose, inlet 2m
701 1 4812 310 18302 Yoke
701 2 4822 480 50159 Sieve inlet
710 0 4812 418 68128 Monoblock
710 2 4819 310 38536 Nut threaded ring set
710 3 4819 466 69562 Gasket set
714 0 4812 462 78993 Threaded cap
714 2 4812 440 18963 Cabinet non-return flap
716 0 4812 418 68147 Reg.dosage
716 1 4812 466 68475 Gasket
716 2 4812 462 78994 Cover
721 0 4812 360 68051 Hub lower cpl.
721 1 4812 360 68047 Arm,spray lower cpl.
721 2 4812 466 68491 Gasket 25x2,3B
721 3 4812 466 68489 Gasket 76x2,5
721 4 4812 440 18977 Flange
722 0 4812 360 68044 Arm,spray upper
722 2 4812 360 68056 Hub upper straight cpl.
723 0 4812 360 68049 Arm,spray
723 1 4812 466 68483 Gasket
723 2 4812 404 48597 Clip,fix sprayarm
723 3 4812 505 18362 Connect,gaspipe
726 0 4812 530 28786 Tube
726 1 4812 530 28787 Tube
726 2 4812 505 18358 Nut
405 1 4819 515 28158 Gasket
420 0 4812 121 18132 Capacitor from 97/08
421 0 4812 121 18156 Interf.filter from 97/07
430 0 4812 360 18357 Pump,draining
430 1 4812 466 68506 Ring,sealing
726 3 4812 466 68512 Gasket
743 1 4812 530 28102 Hose, inlet
751 0 4812 418 18169 Water collector
751 1 4812 418 18171 Water guide
751 2 4812 440 18954 Fastener frame
Whirlpool Europe 03.11.1997 / Page 5
SERVICE
Customer Service Doc. No: 4812 718 12552
Spare part list
Model ADG 953/1 S
Service No. 854295338110
Version 854295338110
Pos. No. 12NC Code Description
751 3 4812 462 78997 Threaded cap
755 0 4812 530 28785 Bend
755 2 4812 530 48148 Tray,leak
756 0 4812 360 58099 Floater
761 0 4812 480 58061 Sieve fine
762 0 4812 480 58062 Microfilter
763 0 4812 480 58057 Sieve coarse
781 0 4812 530 28737 Hose,draining
781 1 4819 530 28286 Sleeve hose
781 2 4819 492 68405 Clip f.non-return valve
781 3 4812 281 28364 Flap non-return
783 4 4812 530 28793 Hose 10x3x230
783 5 4812 530 78027 Distributor
783 6 4812 530 28796 Hose 10x3x180+10
791 0 4812 532 68067 Gasket
791 2 4812 530 58093 Gasket
791 4 4812 466 68503 Gasket
791 5 4812 466 68504 Gasket
794 1 4819 530 58032 Gasket 20x2,5
901 0 4812 401 18191 Strap 017,8
901 1 4812 401 18396 Strap
901 2 4812 401 18401 Strap
901 5 4812 401 18406 Strap 028,6-708Z
901 6 4812 401 18408 Strap 038,1-708Z
901 8 4812 401 18393 Strap 20-32/9
902 1 4812 466 78361 Fastener f.buildt-in models
902 2 4812 404 78239 Holder
904 0 4812 462 78998 Threaded cap
904 2 4812 462 79635 Cover WH 3,5x5
904 4 4812 462 79648 Threaded cap
910 1 4812 502 18019 Screw
910 2 4812 502 18363 Screw 4,0x12-H
910 3 4812 502 18364 Screw 5x20-TORX
910 4 4812 502 18386 Screw 3,5x8-TORX T15
910 5 4812 502 18367 Screw 3,5x8-TORX T15
910 6 4812 502 18369 Screw A2F M4x6
910 7 4812 502 38132 Screw DIN 965
964 1 4812 466 68511 Gasket housing upper
993 1 4812 466 78018 Foil protection
993 2 4812 404 48609 Socket wreng foot
03.11.1997 / Page 6 ADG 953/1 S Whirlpool Europe
Doc. No: 4812 718 12552 8542 953 38110 Customer Service
Exploded view
SERVICE
Loading...