WHIRLPOOL ADG 5010 User Manual

Quick reference guide				Chart

				(see at right for options description)
PROGRAMS SELECTION			START/RESUME BUTTON			CANCEL/OFF BUTTON
BUTTON			Push this button to start the selected program: the			Push this button to switch off the control panel.
Push “P” button (repeatedly)			indicator lights up and goes off at the end of the			If pressed when a program is running it cancels the
until selected program number			program.			program ongoing draining water for 1 minute
is shown on the display			When the door is opened during a washing cycle,			(0:01 is shown into the display).
(P1...Px) - see “Table of			the cycle is temporarily paused: the Start indicator			If pressed when the dishwasher is switched off,
programs” below.			blinks. To resume the cycle push Start button and			it drains any possible liquids from dishwasher
			close the door within 3 seconds.			(1 minute process).

		Table of programs							Consumption
							Deter-				Drying
	Programs		Available			Loading instructions	gent	Litres	kWh	Minutes1)	Phase
			options
P1	Sensor	40°-70°C	Delay			Recommended program for routine
			1/2 load				X	7-15	1.00-1.70	70-172	Full
						washes, with dried-on food.
			PowerClean®
P2	Pre-Wash	cold	Delay			Crockery to be washed later.	—	4.0	0.01	14-16	NO
P3	Rapid	45°C	Delay			Lightly soiled crockery, with no dried-	X	11.0	0.85	30-50	NO
						on food.
P4			Delay			Normally soiled crockery.
	Eco 2)	50°C				Standard program, the most efficient
			1/2 load				X	10.0	0.92	240	Full
						in terms of its combined energy and
			PowerClean®
						water consumption.
P5	Daily	60°C	Delay			Normally to heavily soiled crockery.	X	11.0	1.30	80-95	Full
			1/2 load
						Program including steam action
P6	Steam		Delay			dedicated for heavily soiled crockery,
				®		pots and pans.	X	14.5	1.75	180-190	Full
			PowerClean			Soaking or hand pretreatment is no
						longer needed.

1)Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

2)Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “[e-mail]”.

*Power consumption in Left-on mode: 1.27 W / Off-mode: 0.40 W

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY

BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

Options and display description

SALT INDICATOR				RINSE AID INDICATOR
When lit (at the end of the cycle),				When lit (at the end of the cycle),
the salt reservoir needs to be				the rinse aid dispenser needs to
refilled.				be refilled.

WASH TIME DISPLAY

Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates the time remaining until program start (h.00) - below 1h (0:min).

If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.

POWERCLEAN® Thanks to the additional power jets this option provides a more intensive and powerful wash in the lower rack, in the specific area. This option is recommended for washing pots and casseroles (see

page 4). Press this button to activate PowerClean (the indicator lights up).

1/2 LOAD BUTTON			TABLET SETTING				DELAYED START BUTTON
Half load cycle can be used			This setting allows to optimize				Push the button (repeatedly)
for the upper or lower			the cycle performances				to delay the start of the
rack.			according the type of				program – delay indicator
Select the required			detergent used.				turns on. Adjustable from 1
program then press the			Push the Tablet button for				to 24 hours. With each press
“Half Load” button - the			3 seconds (until the indicator				of the button, the delay
light comes on.			lights up) if you are using the				increases by one hour and
Turns off at the end of the			combined detergents in tablet				after “h 24” returns to
program.			(rinse aid, salt and detergent in				“h 00”. When this option is
The “Half Load” option			1 dose). If you are using				selected the delay indicator
can be used with the			powder detergent or gel				turns on. Then press the
programs indicated in the			detergent, the Tablet indicator				START button. The
table of programs.			on the control panel has to be				dishwasher will start after the
			off.				set time.

5019 300 02468

Whirlpool is a registered trademark of Whirlpool USA	EN -1-

How to set water hardness in order to always assure the best cleaning results

First time use

	10	4
	9
	1

3 2

5

6

7

8

1- salt reservoir

2- rinse aid dispenser

3- detergent dispenser

4- racks system

5,6,7,8- available functions on the panel

9- filters

10spray arms

Water hardness should be set before the first wash or if water hardness has been changed

Water hardness level is factory set for mediumhard water (level 4).

Detergents

When you use Powder or Gel you must use salt and set up water hardness level as indicated in the table on the right.

Also when you use Tablets which include salt functionality you must still add regeneration salt.

-Press and hold together PROGRAM Selection and CANCEL/Off buttons for minimum 3 seconds.

-The current water hardness setting will be visible on the display.

-Press the PROGRAM Selection button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of the start button will set the level back to 1).

-Wait 30 seconds (control panel switches off) or press Start/Resume button to save setting.

	1. Ask your water supply company what the water hardness is...						2. ...enter this value on
							your dishwasher	SALT
	German		French		English	Water hardness	Insert value is shown	required
	degrees °dH		degrees °fH		degrees °eH	level	in the display
	0	- 5	0	- 9	0 - 6.3	Soft	1	NO
	6 - 10		10	- 18	7 - 12.6	Medium	2
	11	- 15	19	- 27	13.3 - 18.9	Average	3
	16	- 21	28	- 37	19.6 - 25.9	Medium-hard	4	YES
	22	- 28	38	- 50	26.6 - 35	Hard	5
	29	- 35	51	- 63	35.7 - 44.1	Very hard	6
	36	- 50	64	- 90	44.8 - 62.4	Extremely hard	7

Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)			Daily check
1	Visual indicator		Screw on the cap.
	(depending		Salt residual
	on the model).		around the cap
	Unscrew cap.		need to be
			removed. Some
			salt reservoir have
			a level indicator
			integrated in the
			cap (see below
			how to check).
	Fill the salt reservoir with water	Add salt (never add detergent!)
	before the first wash only.	min. 0.8 kg / max. 1 kg

Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient).

Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components.

The guarantee is not applicable if faults are caused by such circumstances.

The salt level indicator lamp may remain lit at the end of several wash cycles. If the water hardness set to level 1 (soft), no salt is required and salt indicator lamp will remain off.

(depending on the model)

Salt indicator on the control panel

The indicator lamp lights up when SALT

NEEDS TO BE ADDED.

Salt indicator on the salt reservoir cap

	green: OK.	clear: NEEDS TO
		BE ADDED

Before first use, run the appliance with detergent and without loading.	EN -2-

Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator

Daily check

2	Visual
	indicator

If required, open the cover B (press the dedicated button).

(depending on the model)

Add rinse aid to the max. line ~150 ml

The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4).

Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.

Check the rinse aid indicator to check the level	Rinse aid indicator on the control panel	Rinse aid indicator on the dispenser
into the dispenser.	The indicator lamp lights up when RINSE AID NEEDS	dark: OK.	clear: NEEDS TO BE ADDED
	TO BE ADDED.

Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.

If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.

Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations			Daily use
Open the cover A	Insert detergent: Tablet / powder / gel into the big chamber.		Shut the cover
(press the dedicated button).	Please look for the recommendation of the detergent manufacturer		by pressing dedicated ribs.
3	on the packaging of the detergent product.
	Only fill the	Use only one tablet per one cycle,
	detergent dispenser	only placed in detergent dispenser.
	prior to starting a
	wash program.	Some type of tablets could not
		dissolve completely during the
		short programs (Fragile, Rapid,
		Handwash); placing the tablet on
		the tub bottom can help dissolving
		and washing.

EN -3-