Whirlpool MGD5100DC0, YWED95HEDU0, YWED97HEDBD0, YWED97HEDC0, 7MWGD95HEDU0 Installation Guide

...

GAS DRYER iNSTALLATiON iNSTRUCTiONS

CANADIAN ELECTRIC DRYER iNSTRUCTiONS

iNSTRUCTiONS POUR L'INSTALLATION

DE LA SI'=CHEUSE A GAZ (E.=U. ET CANADA)

i'=LECTRIQUE (CANADA UNIQUEMENT)

Table of Contents

DRYER SAFETY .......................................................................... 2

iNSTALLATiON REQUIREMENTS .............................................. 4

Tools and Parts ...................................................................... 4

LOCATION REQUIREMENTS ..................................................... 5

ELECTRIC DRYER POWER HOOKUP-CANADA ONLY ........... 6

GAS DRYER POWER HOOKUP ................................................. 7

iNSTALL LEVELING LEGS .......................................................... 9

MAKE GAS CONNECTION ......................................................... 9

VENTING .................................................................................... 10

Venting Requirements ......................................................... 10

Plan Vent System ................................................................. 11

Install Vent System .............................................................. 12

CONNECT iNLET HOSE (STEAM MODEL ONLY) ................... 12

CONNECT VENT ....................................................................... 14

LEVEL DRYER ........................................................................... 14

COMPLETE INSTALLATION CHECKLIST ............................... 15

DOOR REVERSAL (OPTIONAL) ............................................... 15

Para una version de estas instrucciones en espa_ol, visite www.Whirlpool.com

iNSTALLATiON NOTES Date of purchase:

Date of installation: Installer: Model number:

Serial number:

Table des mati_res

SECURITE DE LA SECHEUSE .................................................. 23

EXIGENCES D'INSTALLATION ................................................. 25

Outillage et pi_ces ............................................................. 25

EXIGENCES D'EMPLACEMENT ............................................... 26

SLeCHEUSE ELECTRIQUE RACCORDEMENT A

UALIMENTATION leLECTRIQUE - CANADA SEULEMENT ..... 27

RACCORDEMENT D'UNE SECHEUSE A GAZ ........................ 28

iNSTALLATiON DES PIEDS DE NIVELLEMENT ...................... 30

RACCORDEMENT AU GAZ ....................................................... 30

EVACUATION ............................................................................. 31

Exigences concernant I'_vacuation ................................. 31

Planification du syst_me d'_vacuation ............................ 32

installation du syst_me d'_vacuation ............................... 34

RACCORDEMENT DU TUYAU D'ALIMENTATION

(MOD_=LE A VAPEUR UNIQUEMENT) ...................................... 34

RACCORDEMENT DU CONDUIT DqeVACUATION ................. 36

REGLAGE DE L'APLOMB DE LA SECHEUSE .......................... 36

ACHEVER UINSTALLATION LISTE DE VLeRIFICATION ........... 37

INVERSION DE LA PORTE (FACULTATIF) ................................ 37

NOTES CONCERNANT L'INSTALLATION

Date d'achat: Date d'installation:

Installateur:

Num_ro de module: Num_ro de s_rie:

W10676163A

W10676164A=SP

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING." These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

WARNING - ...i.. ofFi,o..

- Clothes dryer installation must be performed by a qualified installer,

- install the clothes dryer according to the manufacturer's instructions and local codes.

- Do not install a clothes dryer with fle×ible plastic venting materials or flexible metal (foil type) duct. if fie×ible metal duct is installed, it must be of a specific type identified

by the appliance manufacturer as suitable for use with clothes dryers. Fle×ible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will

obstruct clothes dryer airflow and increase the risk of fire.

= To reduce the risk of severe injury or death, follow all installation instructions, = Save these instructions,

WARNING: For your safety, the information in this manual must be followed to minimize I the risk of fire or explosion, or to prevent property damage, personal injury, or death, j

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO iF YOU SMELL GAS:

®Do not try to light any appliance. ®Do not touch any electrical switch; do not use any phone in your building.

®Clear the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

o if you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier. If a gas leak is detected, follow the "What to do if you smell gas" instructions.

iMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSi Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

In the State of Massachusetts, the following installation instructions apply:

[] installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] if using a ball valve, it shall be a T-handle type. [] A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT SAFETY INSTRUCTIONS

When discarding or storing your old clothes dryer, remove the door.

SAVE THESE INSTRUCTIONS

iNSTALLATiON REQUIREMENTS

TOOLS AND PARTS

Gather the required tools and parts before starting installation.

" , tall_

Flat-blade screwdriver

#2 Phillips screwdriver

Parts supplied (all models):

Leveling legs (4)

Parts supplied {steam models):

1/4" and 5/16" nut driver Level

recommended)

Tape measure Pliers

Utility knife Tin snips (new vent installations)

Caulking gun and compound Adjustable wrench that opens to (new vent installations) 1" (25 mm) or hex-head socket wrench

"Y" connector

Rubber washer

Parts package is located in dryer drum. Check that all parts are included.

NOTE: Do not use leveling legs supplied with dryer if installing with a pedestal or a stack kit.

Parts needed: (Not supplied with dryer) [] Vent clamps

[] Vent elbows and vent work

2' (0.6 m) inlet hose

Parts needed {steam models):

Tools needed for gas installations:

8" or 10" pipe wrench

Pipe-joint compound resistant to LP gas

8" or 10" adjustable wrench (for gas connections)

5' (1.52 m) inlet hose

Additional parts may be required, depending in your installation. Check local codes. Check existing electrical supply and venting.

Read "Electrical Requirements" and "Venting Requirements" before purchasing parts.

Optional Equipment: (Not supplied with dryer) Refer to your Use and Care Guide for information about

accessories available for your dryer.

LOCATION REQUIREMENTS

DRYER DiMENSiONS Front view:

383//4'' Min.

(984rnrn)

4-- 27" --_

(686 mrn)

Explosion Hazard

Keep flammabJe materials and vapors, such as gasoline, away from dryer.

Place dryer at (east 18 inches (460 ram) above the floor for a garage installation.

FaiJure to do so can result in death, explosion, or fire.

You will need:

[] A location allowing for proper exhaust installation.

See "Venting Requirements."

[] A separate 15 or 20 amp circuit for a gas dryer or 30 amp

circuit for an electric dryer.

[] If using power supply cord, a grounded electrical outlet

located within 2 ft. (610 mm) of either side of dryer. See "Electrical Requirements."

[] Floor must support dryer weight of 200 Ibs. (90.7 kg).

Also consider weight of companion appliance.

[] Cold water faucets located within 4 ft. (1.2 m) of the water

fill valves, and water pressure of 20 - 120 psi (138 - 827 kPa). You may use the water supply for your washer using the supplied "Y" connector and a short hose (which you will need to purchase).

[] Level floor with maximum slope of 1" (25 mm) under entire

dryer. If slope is greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Number 279810. If not level, clothes

may not tumble properly and automatic sensor cycles may not operate correctly.

[] For garage installation, place dryer at least 18" (460 mm)

above floor, if using a pedestal, you will need 18" (460 mm) to bottom of dryer.

[] The dryer must not be installed or stored in an area where

it will be exposed to water and/or weather.

iMPORTANT: Do not operate, install, or store dryer where

it will be exposed to water, weather, or at temperatures below 40° F (4° C). Lower temperatures may cause dryer not to shut off at end of automatic sensor cycles, resulting in longer drying times.

Side view:

Back view:

39" Max,

(990 ram)

3/4_1"

(18 rnrn)

51 j_

(1220 mm)

31"

(787mm)

53/4 _*

(146 rnm)

J 31/2"

• + +

(257 ram)

• Approx. measurement

61/4"

(159 ram)

297/8"*

Waterinlet

(Steam Models Onl

Vent m_J

(759 ram}

--d

(156 ram)

Approx. measurement

NOTE: Most installations require a minimum of 5" (127 mm) clearance behind dryer for exhaust vent with elbow. See

"Venting Requirements."

Installation Clearances For each arrangement, consider allowing more space for ease

of installation and servicing; spacing for companion appliances and clearances for walls, doors, and floor moldings. Space must be large enough to allow door to fully open. Add spacing on all sides of dryer to reduce noise transfer. If a closet door or Iouvered door is installed, top and bottom air openings

in door are required. Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.

NOTE: No other fuel-burning appliance can be installed in the same closet as a dryer.

Mobile home installations require: [] Metal exhaust system hardware, available for purchase from

your dealer. For further information, see "Assistance or Service" section in your Use and Care Guide.

[] Special provisions must be made in mobile homes to

introduce outside air into dryer. Openings (such as a nearby window) should be at least twice as large as dryer exhaust opening.

For mobile home installation of gas dryers:

[] Mobile Home Installation Hold-down Kit Part Number 346764

is available to order. For further information, see "Assistance or Service" section in your Use and Care Guide.

installation spacing for recessed area or closet installation

All dimensions show recommended and minimum spacing allowed.

[] Additional spacing should be considered for ease of

installation and servicing.

[] Additional clearances might be required for wall, door, floor

moldings, dryer venting, and gas line.

[] Additional spacing should be considered on all sides

of the dryer to reduce noise transfer.

[] For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

[] Companion appliance spacing should also be considered.

Recommended installation clearances {dryer only):

', "':-=2

5 n * i i,

(127 rnrn} "

* 0" (0 mm) spacing is allowed.

(76 ram)

ELECTRIC DRYER POWER HOOKUP - CANADA ONLY

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into a grounded 4 prong outlet, Failure to do so can result in death or electrical shock.

It is your responsibility:

[] To contact a qualified electrical installer. [] To be sure that the electrical connection is adequate and in

conformance with Canadian Electrical Code, C22.1 - latest edition and all local codes. A copy of above codes standard

may be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

[] To supply the required 4 wire, single phase, 120/240 volt,

60 Hz, AC only electrical supply on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit

breaker is recommended. Connect to an individual branch circuit.

[]

This dryer is equipped with a CSA International Certified Power Cord

intended to be plugged into a standard 14-30R wall receptacle. The cord is 5 ft. (1.52 m) long. Be sure wall receptacle is within reach of dryer's final location.

4-wire receptacle

(14-30R)

Mobile home = Additional installation requirements: This dryer is suitable for mobile home installations.

The installation must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR,

Part 3280 (formerly the Federal Standard for Mobile home construction and Safety, Title 24, HUD Part 280) or Standard

CAN/CSA-Z240 MH.

If using a replacement power supply cord, it is recommended that you use Power Supply Cord Replacement Part Number 8529008.

For further information, please reference service numbers located in "Assistance or Service" section of your Use and Care Guide.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer: This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current. This dryer is equipped with a cord having an equipment- grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes and ordinances.

WARNING-" Improper connection of the equipment- grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer: This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer is equipped with a cord having an equipment- grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes

and ordinances. WARNinG-" improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

GAS SUPPLY REQUIREMENTS

GAS DRYER POWER HOOKUP

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

[] 120 Volt, 60 Hz, AC only, 15- or 20- amp fused electrical

supply is required. A time-delay fuse or circuit breaker is recommended. It is also recommended that a separate circuit

serving only this dryer be provided.

Explosion Hazard

Use a new CSA international approved gas supply line.

Install a shut=off valve. Securely tighten all gas connections.

if connected to LP, have a qualified person make sure gas pressure does not exceed 13" (330 ram) water

column.

Examples of a qualified person include: licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

GAS TYPE

Natural Gas: This dryer is equipped for use with Natural gas. It is design-

certified by CSA international for LP (propane or butane) gases with appropriate conversion.

[] Your dryer must have the correct burner for the type of gas in

your home. Burner information is located on the rating plate in the door well of your dryer. If this information does not agree with the type of gas available, contact your dealer or call the phone numbers referenced in the "Assistance or Service" section of your Use and Care Guide.

LP Gas Conversion: iMPORTANT: Conversion must be made by a qualified

technician. No attempt shall be made to convert the appliance from the gas

specified on the model/serial rating plate for use with a different gas without consulting your gas company.

GASSUPPLYLiNE

Option 1 (Recommended Method) Flexible stainless steel gas connector: [] If local codes permit, use a new flexible stainless steel gas

connector (Design Certified by the American Gas Association or CSA International) to connect your dryer to the rigid gas supply line. Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting between the stainless steel gas connector and the dryer gas pipe, as needed to prevent kinking.

Option 2 (Alternate Method) Approved aluminum or copper tubing: [] Must include 1/8" NPT minimum plugged tapping accessible

for test gauge connection, immediately upstream of the gas

connection to the dryer. See illustration. [] 1/2" IPS pipe is recommended. [] 3/8" approved aluminum or copper tubing is acceptable for

lengths under 20 ft. (6.1 m) if local codes and gas supplier

permit. [] If you are using Natural gas, do not use copper tubing. [] Lengths over 20 ft. (6.1 m) should use larger tubing and

a different size adapter fitting. [] If your dryer has been converted to use LP gas, 3/8" LP

compatible copper tubing can be used. If the total length of the

supply line is more than 20 ft. (6.1 m), use larger pipe.

NOTE: Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON_'*_ttape.

[] Must include shut-off valve

GAS SUPPLY CONNECTION REQUIREMENTS [] Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting

between the flexible gas connector and the dryer gas pipe,

as needed to avoid kinking. [] Use only pipe-joint compound. Do not use TEFLON <etape. [] This dryer must be connected to the gas supply line with a

listed flexible gas connector that complies with the standard for

connectors for gas appliances, ANSi Z21.24 or CSA 6.10. BURNER INPUT REQUIREMENTS

Elevations above 2,000 ft. (610 m): [] When installed above 2,000 ft. (610 m) a 4% reduction of the

burner Btu rating shown on the model/serial number plate is

required for each 1,000 ft. (305 m) increase in elevation.

Gas supply pressure testing [] The dryer must be disconnected from the gas supply piping

system during pressure testing at pressures greater than

1/2 psi.

DRYER GAS PiPE [] The gas pipe that comes out through the rear of your dryer has

a 3/8" male pipe thread.

in the U.S.A.:

An individual manual shut-off valve must be installed within six (6) ft. (1.8 m) of the dryer in accordance with the National

Fuel Gas Code, ANSi Z223.1. The location should be easy to reach for opening and closing.

In Canada:

An individual manual shut-off valve must be installed in accordance with the B149.1, Natural Gas and Propane

installation Code. It is recommended that an individual manual shut-off valve be installed within six (6) ft. (1.8 m) of

the dryer. The location should be easy to reach for opening and closing.

A !_

A. 3/8" flexible gas connector B. 3/8" pipe to flare adapter fitting C. 1/8" NPT minimum plugged tapping D. 1/2" NPT gas supply line

E. Gas shut-off valve.

1/2nn

(38 ram)

*5¾"

3/8" NPT dryer gas pipe

(146 ram}

* NOTE: If the dryer is mounted on a pedestal, the gas

pipe height must be an additional 10" (254 mm) or

15.5" (394 mm) from the floor, depending on the pedestal model. For a garage installation, the gas pipe height must

be an additional 18" (460 mm) from the floor.

t®TEFLON is a registered trademark of E.I. Dupont De Nemours and Company.

iNSTALL LEVELING LEGS

MAKE GAS CONNECTION

(gas models only)

Excessive Weight Hazard Use two or more people to move and install dryer. Failure to do so can result in back or other injury.

(1, Prepare dryer for leveling legs

m m

To avoid damaging floor, use a large flat piece of cardboard from dryer carton; place under entire back edge of dryer.

Firmly grasp dryer body (not console panel) and gently lay

dryer down on cardboard.

1. Connect gas supply to dryer

• • B

A. Flaredmale fitting B. Non-flared male fitting

Remove red cap from gas pipe. Using a wrench to tighten, connect gas supply to dryer. Use pipe-joint compound on threads of all non-flared male fittings. Ifflexible metal

tubing is used, be sure there are no kinks.

NOTE: For LP gas connections, you must use pipe-joint compound resistant to action of LP gas Do not use

TEFLON ®tape.

2, Screw in leveling legs _%

)

Examine leveling legs, find diamond marking. Screw legs into leg holes by hand - use a wrench to finish turning legs until

diamond marking is no longer visible. Place a carton corner post from dryer packaging under each

of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent.

A combination of pipe fittings must be used to connect dryer to existing gas line. A recommended connection is shown.

Your connection may be different, according to supply line type, size, and location.

f3, Open shut=off valve

A. Closedvalve B. Openvalve

Open shut-off valve in supply line; valve is open when handle

is parallel to gas pipe. Then, test all connections by brushing

on an approved noncorrosive leak-detection solution.

Bubbles will show a leak. Correct any leak found.

VENTING

Venting Requirements

Fire Hazard

Use a heavy metal vent. Do not use a plastic vent,

Do not use a metal foil vent. Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS. iMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, attic, crawlspace, or a concealed space of a building. Only rigid or flexible metal vent shall be used for exhausting.

Exhaust hoods: [] An exhaust hood should cap the vent to keep rodents and

insects from entering the home.

[] Must be at least 12" (305 mm) from ground or any object

that may obstruct exhaust (such as flowers, rocks, bushes,

or snow).

[] Do not use an exhaust hood with a magnetic latch.

Recommended Styles:

Louvered Hood

Box Hood

Acceptable Style:

Angled Hood

Elbows: [] 45° elbows provide better airflow than 90° elbows.

( 0'

(102 ram)

4" (102 ram) heavy metal exhaust vent

[]

Only a 4" (102 mm) heavy metal exhaust vent and clamps may be used.

[]

Do not use plastic or metal foil vent.

Rigid metal vent: [] Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only ifaccessible to clean) [] Must be fully extended and supported in final dryer location. [] Remove excess to avoid sagging and kinking that may result

in reduced airflow and poor performance.

[] Do not install in enclosed walls, ceilings, or floors. [] The total length should not exceed 73/4ft. (2.4 m). [] The length of flexible metal vent used must be included in

the overall vent system design as shown in the "Vent System Charts."

NOTE: If using an existing vent system, clean lint from entire

length of the system and make sure exhaust hood is not plugged with lint. Replace plastic or metal foil vents with rigid metal or flexible metal vents. Review "Vent System Charts" and if necessary, modify existing vent system to achieve best drying

performance.

Bet

Clamps: [] Use clamps to seal all joints.

[] Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct and catch lint. Do not use duct ta }e.

improper venting can cause moisture and lint to collect indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

Plan Vent System

Choose your exhaust installation type

Recommended exhaust installation:

A. Dryer E Rigid metal or B Elbow flexible metal vent

C. Wall G. Vent length D. Exhaust hood necessary to

E. Clamps connect elbows

H. Exhaust outlet

Special provisions for mobile homes: Exhaust vent must be securely fastened to a noncombustible

portion of mobile home and must not terminate beneath the

mobile home. Terminate exhaust vent outside.

t-4 _-

Determine vent path: [] Select route that will provide straightest and most direct

path outdoors.

[] Plan installation to use fewest number of elbows and turns. [] When using elbows or making turns, allow as much room

as possible. [] Bend vent gradually to avoid kinking. [] Use as few 90° turns as possible.

Fire Hazard

Cover unused exhaust holes with a manufacturer's exhaust cover kit.

Contact your local dealer.

Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

Optional exhaust installations: This dryer can be converted to exhaust out the right side, left

side (all models except WGD71HEW), or through the bottom. If you prefer, you may contact your local dealer to have the dryer converted.

A B C

A. Standard rear offset exhaust installation

B. Left- or right-side exhaust installation C. Bottom exhaust installation

Determine vent length and elbows needed for best drying performance:

[] Use the "Vent System Charts" on the next page to determine

type of vent material and hood combinations acceptable to

use.

NOTE: Do not use vent runs longer than those specified in "Vent System Charts."

Exhaust systems longer than those specified will:

[] Shorten life of dryer. [] Reduce performance, resulting in longer drying times

and increased energy usage.

The "Vent System Charts" provide venting requirements

that will help achieve best drying performance.

Install Vent System

Standard Vent System Chart

Number of Type Angled

90° elbows of vent hoods

0 Rigid metal 64 ft. (20 m)

1 Rigid metal 54 ft. (16.5 m)

2 Rigid metal 44 ft. (13.4 m) 3 Rigid metal 35 ft. (10.7 m)

4 Rigid metal 27 ft. (8.2 m)

Long Vent System Chart*

Number of Type Angled

90° elbows of vent hoods

0 Rigid metal 160 ft. (48.8 m) 1 Rigid metal 150 ft. (45.7 m) 2 Rigid metal 140 ft. (42.7 m)

3 Rigid metal 130 ft. (39.6 m) 4 Rigid metal 120 ft. (36.6 m)

*For Model WGD71 HEW only; for all other models, refer to the

Standard Vent System Chart above. To find your model number, refer to the model and serial number plate in the inner door well.

NOTE: For long vent systems, use of box/Iouvered hoods will

improve venting regardless of length.

f, Install exhaust hood

Install exhaust hood and use caulking compound to seal exterior wall opening around exhaust hood.

2. Connect vent to exhaust hood

Vent must fit over the exhaust hood. Secure vent to exhaust

hood with 4" (102 mm) clamp. Run vent to dryer location using

straightest path possible. Avoid 90° turns. Use clamps to seal

all joints. Do not use duct tape, screws, or other fastening devices that extend into interior of vent to secure vent,

because they can catch lint.

CONNECT iNLET HOSE

(STEAM MODEL ONLY)

For non-steam models, skip to "Connect Vent."

The dryer must be connected to the cold water faucet using the

new inlet hoses (not supplied). Do not use old hoses.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Record hose installation or replacement dates on

the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.

1. Turn cold water off, remove hose, and replace rubber washer

Turn cold water faucet off and remove washer inlet hose.

Remove old rubber washer from inlet hose and replace with new rubber washer.

Attach 2 ft (0.6 m) inlet hose to cold water faucet. Screw on coupling by hand until it is seated on faucet. Then attach "Y" connector to male end of the 2 ft (0.6 m) inlet hose. Screw on coupling by hand until it is seated on connector.

Attach long hose to dryer fill valve and tighten coupling

Remove protective cap from water inlet valve. Attach other end

of long hose to fill valve at bottom of dryer back panel. Screw on coupling by hand until it is seated on fill valve connector. Using pliers, tighten the couplings an

additional two-thirds turn. NOTE: Do not overtighten. Damage to the coupling

can result.

Using pliers, tighten the couplings with additional two-thirds turn. NOTE: Do not overtighten. Damage to the coupling can result.

connector and tighten couplings

Attach one of the 5 ft (1.5 m) inlet hose ends to the "Y" connector. Attach washer cold inlet hose to other side of

"Y" connector. Screw on coupling by hand until it is seated on connector. Using pliers, tighten the couplings an additional two-thirds turn.

NOTE: Do not overtighten. Damage to the coupling can result.

Check that the water faucets are turned on.

Check for leaks around "Y" connector, faucet, and hoses.

CONNECT VENT

LEVEL DRYER

1. Connect vent to exhaust outlet

Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure vent is clean. Dryer vent must fit over dryer exhaust outlet and inside

exhaust hood. Check that vent is secured to exhaust hood with a 4" (102 mm) clamp.

2. Move dryer to final location

fl -. Level dryer

Place

level here

Check levelness of dryer from side to side. Repeat from front to back.

NOTE: The dryer must be level for the moisture sensing system to operate correctly

Move dryer to final location, taking care not to crush or

kink vent or flexible gas line. After dryer is in place, remove corner posts and cardboard

from under dryer.

Not Level LEVEL Not Level

Adjust leveling legs

If dryer is not level, prop up using a wood block, use wrench to adjust legs up or down, and check again for levelness. Once dryer is level, make sure all four legs are snug against the floor and the dryer does not rock.

+ 30 hidden pages