Whirlpool 3RLSQ8000 User Manual

Part No. 8318424 Rev. A

Installation

Instructions

IMPORTANT:

Read and save these instructions.

Installer: Leave Installation Instructions with the homeowner Homeowner: Keep Installation Instructions for future reference. Save Installation Instructions for local electrical inspector’s use.

230-volt, 50-Hz

Washer

for models

3RLBR8543 3RLSQ8000 3RGSC9455 3SLSQ7533 3RLSQ8533

Panel A

Location of washer

Introduction

Before you start

Recessed area/closet installation

Front view (door not shown)

Side view

The installation dimensions shown are the minimum spaces allowable. Additional spacing should be considered for ease of installation and servicing.

Additional clearances for wall, door and floor moldings may be required. Allow 2.5 cm (1 inch) of space between washer and dryer.

If closet door is installed, the minimum air openings in top and bottom of door are required. Louvered doors with air openings in top and bottom are acceptable.

Companion appliance spacing should be considered.

Front view

closet door

7,6 cm (3")

155 cm

(24 inches2)

310 cm

(48 inches2)

0 cm (0")

43,2 cm (17")

closet door

35,6 cm máx. (14" max.)

10,2 cm mín. (4" min.)

2,5 cm mín. (1" min.)

155 cm

(24 inches2)

310 cm

(48 inches2)

Important: Observe all governing codes and ordinances.

Check location where washer will be installed. Make sure you

have everything necessary for correct installation. Proper installation is your responsibility.

Water heater: Set to deliver 60°C (140°F) water to washer. Earthed electrical outlet (A) is required within 152 cm

(5 feet) of upper left corner of washer cabinet. See “Electrical requirements”, Panel B.

The installer is to confirm, through the local power supply authority, if necessary, that the machine is connected to a power supply with a maximum impedance of 0.068 + j0.043 ohms for phases (RA + jXA) and 0.0455 + j0.02844 ohms for neutral (RN + jXN).

Hot and cold water faucets (B): Must be within 122 cm (4 feet) of the upper right corner of the washer cabinet and provide water pressure 34.5-689.6 kPa (5-100 psi).

The hot and cold water inlets on the back of the washer have 3/4 — 11-1/2 American hose coupling standard threads.

Level floor (C): Maximum slope under entire

washer —

2.5 cm (1 inch). Installing washer on carpeting is not recommended.

Support (D): Floor must be sturdy enough to support washer weight (with water) of 143 kilograms (315 pounds).

The minimum and maximum motor rotation per minute (R.P.M.) is 950-1425 R.P.M. The minimum and maximum basket R.P.M. is 423-640 R.P.M.

Allow 2.5 cm (1 inch) of space between washer and dryer.

Do Not store or operate washer below 0°C (32°F) (some water may remain in washer).

See Use & Care Guide for “Winterizing” information.

Your safety and the safety of others are very

important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards

that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING”. These words mean:

You can be killed or seriously injured if you don’t immediately

follow instructions.

You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

WARNING

D ANGER

Tools needed for installation

Parts supplied for installation

A. level B. wrench C. utility knife D. pliers E. scissors

A. 1 drain hose B. 2 inlet hoses C. 1 yellow clamp D. 2 drain hose clamps E. 2 front leveling legs

with nuts

F. 6 flat water hose

washers G. 1 hose extension H. literature package

I. faucet adapters

Remove parts from packages. Check that all parts were included.

+ 3 hidden pages