Page 1
WASHER INSTALLATION INSTRUCTIONS
INSTRUCCIONES DE INSTALACIÓN DE LA LAVADORA
Table of Contents Índice
WASHER SAFETY ..............................................................1
INSTALLATION REQUIREMENTS .....................................2
Tools and Parts ..................................................................... 2
Location Requirements .......................................................2
Drain System ........................................................................ 3
Electrical Requirements ......................................................4
INSTALLATION INSTRUCTIONS .......................................4
Before you start: remove shipping materials ....................4
Connect Drain Hose ............................................................. 5
Connect Inlet Hoses ............................................................. 6
Level Washer ........................................................................7
Power Cord Installation ....................................................... 8
Complete Installation Checklist .......................................... 8
INSTALLATION NOTES
Date of purchase: _________________________________
Date of installation: _______________________________
Installer: ________________________________________
Model number: ___________________________________
Serial number: ___________________________________
SEGURIDAD DE LA LAVADORA .................................9
REQUISITOS DE INSTALACIÓN .................................9
Herramientas y piezas ...................................................9
Requisitos de ubicación ...............................................10
Sistema de desagüe ......................................................11
Requisitos eléctricos ....................................................11
INSTRUCCIONES DE INSTALACIÓN ........................12
Antes de comenzar: quite los materiales
de transporte .................................................................12
Conexión de la manguera de desagüe ........................ 13
Conexión de las mangueras de entrada .....................14
Nivelación de la lavadora .............................................15
Instalación del cable eléctrico ................Contraportado
Complete la instalación ...........................Contraportado
NOTAS SOBRE LA INSTALACIÓN
Fecha de compra: ________________________________
Fecha de instalación: ______________________________
Instalador: ______________________________________
Número de modelo: _______________________________
Número de serie: _________________________________
WASHER SAFETY
W10807863C
Page 2
271/2"
INSTALLATION REQUIREMENTS
Tools and Parts
Gather required tools and parts before starting installation.
Tools needed:
Inlet hoses with
flat washers
Rubber washer
Alternate parts: (Not supplied with washer)
Your installation may require additional parts.
Adjustable or open-end
wrench
Wood block
Pliers that open to
13⁄4" (44.5 mm)
9
⁄
” (14 mm)
16
4" min
(102 mm)
Optional tools:
Level
Ruler or measuring tape
If you have: You will need:
Overhead sewer Standard 20 gal. (76 L) 39" (990 mm)
tall drain tub or utility sink, sump
pump, and connectors (available from
local plumbing suppliers)
1" (25 mm) standpipe 2" (51 mm) diameter to 1" (25 mm)
diameter Standpipe Adapter
Part Number 3363920
Connector Kit Part Number 285835
Drain hose too short Extension Drain Hose Part
Number 285863
Connector Kit Part Number 285835
Lint clogged drain Drain Protector Part Number 367031
Connector Kit Part Number 285835
LOCATION REQUIREMENTS
Select proper location for your washer to improve performance
and minimize noise and possible “washer walk.” Install your
washer in a basement, laundry room, closet, or recessed area.
(699 mm)
27"
(686 mm)
Flashlight Bucket
Parts supplied:
NOTE: All parts supplied for installation are in cardboard
insert in the top of the washer.
Drain hose with clamp,
U-form, and cable tie
Plugs and cord lock cover
“Y” connector
2
42"
(1067 mm)
Page 3
You will need:
3"
4.5"
(114 mm)
n
A water heater set to 120°F (49°C).
n
A grounded electrical outlet located within 4 ft (1.2 m)
of power cord on back of washer.
n
Hot and cold water faucets located within 3 ft (0.9 m) of hot
and cold water fill valves on washer; and water pressure
of 20–100 psi (138–690 kPa).
n
A level floor with maximum slope of 1" (25 mm) under entire
washer. Installing on carpet is not recommended.
n
Floor must support washer’s total weight (with water and load)
of 315 lbs (143 kgs).
IMPORTANT: Do not install, store, or operate washer where it
will be exposed to weather or in temperatures below 32°F (0°C).
Water remaining in washer after use may cause damage in low
temperatures. See “Washer Care” in your Use and Care Guide
for winterizing information.
Proper installation is your responsibility.
Recessed area or closet installation
(76 mm)
14" max.
(356 mm)
17"
(432 mm)
2
48 in.
(310 cm2)
DRAIN SYSTEM
Drain system can be installed using a floor drain, wall standpipe,
floor standpipe, or laundry tub. Select method you need.
Floor standpipe drain system
39"
4.5"
(114 mm)
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe
must be at least 39" (990 mm) high; install no higher than
96" (2.44 m) from bottom of washer. If you must install higher
than 96" (2.44 m), you will need a sump pump system.
Wall standpipe drain system
4.5"
(114 mm)
See requirements for floor standpipe drain system.
Floor drain system
(990 mm)
2
24 in.
5"
(126 mm)
1"
1"
(25 mm)
Dimensions show recommended spacing allowed, except for
closet door ventilation openings, which are minimum required.
(25 mm)
(155 cm2)
3"
(76 mm)
This washer has been tested for installation with spacing of
0" (0 mm) clearance on the sides. Consider allowing more space
for ease of installation and servicing, and spacing for companion
appliances and clearances for walls, doors, and floor moldings.
Add spacing of 1" (25 mm) on all sides of washer to reduce
noise transfer. If a closet door or louvered door is installed,
top and bottom air openings in door are required.
Floor drain system requires a Siphon Break Kit (Part Number
285834), 2 Connector Kits (Part Number 285835), and an
Extension Drain Hose (Part Number 285863) that may be
purchased separately. Minimum siphon break: 28" (710 mm)
from bottom of washer. (Additional hoses may be needed.)
Laundry tub drain system
39"
(990 mm)
Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at
least 39" (990 mm) above floor; install no higher than 96" (2.44 m)
from bottom of washer.
IMPORTANT: To avoid siphoning, no more than 4.5" (114 mm)
of drain hose should be inside standpipe or below the top of
wash tub. Secure drain hose with cable tie.
3
Page 4
ELECTRICAL REQUIREMENTS
n
A 220–240 volt, 50/60 Hz., AC only, 15- or 20-amp, fused
electrical supply is required. A time-delay fuse or circuit breaker
is recommended. It is recommended that a separate circuit
breaker serving only this appliance be provided.
n
This washer is equipped with a power supply cord having
a 3 prong grounding plug.
n
To minimize possible shock hazard, the cord must be plugged
into a mating, 3 prong, grounding-type outlet, grounded in
accordance with local codes and ordinances. If a mating outlet
is not available, it is the personal responsibility and obligation
of the customer to have the properly grounded outlet installed
by a qualified electrician.
n
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that
the ground path is adequate.
n
Do not ground to a gas pipe.
n
Check with a qualified electrician if you are not sure the
washer is properly grounded.
n
Do not have a fuse in the neutral or ground circuit.
INSTALLATION INSTRUCTIONS
Before you start: Remove shipping materials
It is necessary to remove all shipping materials for proper
operation and to avoid excessive noise from washer.
1. Move washer
48"
(1.2 m)
Move washer to within 4 ft (1.2 m) of its final location; it must
be in a fully upright position.
NOTE: To avoid floor damage, set washer onto cardboard
before moving it and make sure lid is taped shut.
2. Remove shipping base
To avoid damaging floor, place cardboard supports from
shipping carton on floor behind washer. Tip washer back and
place on cardboard supports. Remove shipping base. Set
washer upright.
IMPORTANT: Removing shipping base is necessary for proper
operation. If your washer includes a sound shield, please refer
to the instructions included with the sound shield to install it at
this time.
4
Page 5
3. Remove packing tray from tub
Remove tape from washer lid, open lid and remove cardboard
packing tray from tub. Be sure to remove all parts from tray.
NOTE: Keep tray in case you need to move washer later.
For a laundry tub or standpipe drain, go to Step 6.
For a floor drain, remove the preinstalled drain hose form as
shown in Step 7. You may need additional parts with separate
directions. See “Tools and Parts.”
6. Place drain hose in standpipe
Drain
hose form
4.5"
(114 mm)
4. Free power cord
Firmly grasp power cord plug and pull to free from rear panel.
Gently place power cord over console to allow free access
to back of washer.
CONNECT DRAIN HOSE
5. Attach drain hose to drain port
Place hose into standpipe (shown in picture) or over side
of laundry tub.
IMPORTANT: 4.5" (114 mm) of drain hose should be inside
standpipe; do not force excess hose into standpipe or lay
on bottom of laundry tub. Drain hose form must be used.
7. Remove drain hose form
(floor drain installations only)
For floor drain installations, you will need to remove the
drain hose form from the end of the drain hose. You may
need additional parts with separate directions. See “Tools
and Parts.”
Remove the red plastic plug from the black drain port on the
back of the washer.
If clamp is not already in place on elbow end of drain hose,
slide it over end as shown. Squeeze clamp with pliers and
slide black elbow end of drain hose onto black drain port
and secure with clamp.
5
Page 6
CONNECT INLET HOSES
Washer must be connected to water faucets with new inlet
hoses with flat washers (not provided). Do not use old hoses.
NOTE: Both hoses must be attached and have water flowing
to inlet valves. If you are only connecting to a cold water
faucet, you must use a Y-adapter (provided).
If you have a hot water faucet, go to Step 8a.
If you have only a cold water faucet, go to Step 8b.
8a. Connect inlet hoses to water faucets
9. Clear water lines
Run water for a few seconds through hoses into a laundry tub,
drainpipe, or bucket to avoid clogs. Water should run until clear.
Make note of which hose is connected to hot water to help in
attaching hoses to washer correctly.
10. Connect inlet hoses to washer
Attach hose to hot water faucet. Screw on coupling by hand
until it is seated on washer. Use pliers to tighten couplings an
additional two-thirds turn. Repeat this step with second hose
for cold water faucet.
IMPORTANT: Do not overtighten or use tape or sealants on
valve when attaching to faucets or washer. Damage can result.
8b.
Attach the brass female end of the “Y”
connector to the cold water faucet. Use pliers to
tighten couplings an additional two-thirds turn. One end of
the long hose has a wire mesh strainer inside the coupling.
Attach this end to the “Y” connector. Attach washer cold inlet
hose to other side of “Y” connector. Screw on coupling by
hand until it is seated on connector. Using pliers, tighten the
couplings an additional two-thirds turn.
IMPORTANT: Do not overtighten or use tape or sealants
on valve when attaching to faucets or washer. Damage
can result.
Connect inlet hoses to “Y” connector
Attach hot water hose to hot water inlet valve marked with a
red ring. Screw coupling by hand until it is snug. Use pliers to
tighten couplings an additional two-thirds turn. Repeat with
cold water inlet valve.
IMPORTANT: To reduce risk of hose failure, replace the hoses
every 5 years. Record hose installation or replacement dates
for future reference.
n
Periodically inspect and replace hoses if bulges, kinks, cuts,
wear, or leaks are found.
11. Check for leaks
Turn on water faucets to check for leaks. A small amount
of water may enter washer. It will drain later.
6
Page 7
12. Secure drain hose
Laundry Tub Standpipe Wall
14. Adjust leveling feet
4.5"
4.5"
(114 mm)
(114 mm)
Secure drain hose to laundry tub leg, drain standpipe, or inlet
hoses for wall standpipe with cable tie.
It is the responsibility of the installer to install and secure the
drain hose into the provided plumbing/drain in a manner that
will avoid the drain hose coming out of, or leaking from, the
plumbing/drain.
4.5"
(114 mm)
4.5"
4.5"
(113 mm)
(114 mm)
LEVEL WASHER
IMPORTANT: Level washer properly to reduce excess noise
and vibration.
13. Check levelness of washer
Place level here
Place level here
Models with
metal feet
Jam nut
or
Models with
plastic feet
If washer is not level:
On models with metal feet, use a
or adjustable wrench to turn jam nuts clockwise on feet until
they are about ½" (13 mm) from the washer cabinet. Then
turn the leveling foot clockwise to lower the washer or
counterclockwise to raise the washer.
On models with plastic feet, use adjustable pliers to turn the
plastic leveling foot counterclockwise to lower the washer
or clockwise to raise the washer. On all models, recheck
levelness of washer and repeat as needed.
HELPFUL TIP: You may want to prop up front of washer
about 4" (102 mm) with a wood block or similar object that
will support weight of washer.
9
⁄
" or 14 mm open-end
16
Move the washer to its final location. Place a level on
top edges of washer. Use side seam as a guide to check
levelness of sides. Check levelness of front using lid as shown.
Rock washer back and forth to make sure all 4 feet make
solid contact with floor. If washer is level, skip to Step 15,
(on models with metal feet) or Step 16 (on models with
plastic feet).
Not Level
LEVEL
Not Level
15. Tighten leveling feet
Jam nut
On models with metal feet, when washer is level, use a
9
⁄
" or 14 mm open-end or adjustable wrench to turn jam
16
nuts counterclockwise on leveling feet tightly against
washer cabinet.
HELPFUL TIP: You may want to prop washer with
wooden block.
7
Page 8
POWER CORD INSTALLATION
9/16
18. Secure power cord
Secure the power cord by seating the connection on the cord
lock. Place the cord lock cover and push until it snaps. Make
sure the power cord connection is seated on the cord lock
and that the cord lock clamps correctly.
Plug power supply cord into an earthed outlet. Turn power
supply on.
16. Select plug
Select the plug that fits with the electric receptacle.
NOTE: Plug types and quantities will vary by model.
17. Assemble plug
COMPLETE INSTALLATION
CHECKLIST
Check electrical requirements. Be sure you have correct
q
electrical supply and recommended grounding method.
Check that all parts are now installed. If there is an extra
q
part, go back through steps to see what was skipped.
Check that you have all of your tools.
q
Check that yellow shipping materials were completely
q
removed from back of washer.
Check that water faucets are on.
q
Check for leaks around faucets and inlet hoses.
q
Remove protective film from console and any tape
q
remaining on washer.
Check that washer is plugged into a grounded 3 prong outlet.
q
Dispose of/recycle all packaging materials.
q
Read “Washer Use” in your Washer Use and Care Guide.
q
To test and clean your washer, measure ½ of normal
q
recommended amount of powdered or liquid detergent
and pour it into washer basket or detergent dispenser
(on some models). Close lid. Select any cycle. Start washer
and allow to complete full cycle.
Assemble the plug into the end of the power cord located on
the back of the washer.
8
Loading...