Whirlpool 2205266 User Manual

TOP-MOUNT

REFRIGERATOR

Use & Care Guide

For questions about features, operation/performance,

parts accessories or service, call: 1-800-253-1301.

In Canada, call for assistance 1-800-461-5681, for installat ion

www.whirlpool.com or www.whirlpool.com/canada

and service, call: 1-800-807-6777

or visit our website at...

RÉFRIGÉRATEUR

SUPERPOSÉ

Guide d’utilisation

et d’entretien

Au Canada, pour assistance, composer le 1-800-461-5681, po ur

T able of Contents /Table des ma tières...................... ........... ........ .2

installation ou service le 1-800-807-6777

ou visitez notre site web à

www.whirlpool.com/canada

2205266

TABLE OF CONTENTS

T A BLE DES MA TIÈRES

REFRIGERATOR SAFETY.......................................................... 3

INSTALLING YOUR REFRIGERATOR....................................... 4

Unpacking Your Refrigerator.......................................................4

Space Requirements....................................................................4

Electrical Requirements...............................................................5

Connecting the Refrigerator to a Water Source..........................5

Base Grille....................................................................................6

Refrigerator Doors: Removing, Reversing and Replacing...........7

Door Closing and Alignment........................................................8

Understanding Sounds You May Hear........................................9

USING YOUR REFRIGERATOR................................................. 9

Ensuring Proper Air Circulation....................................................9

Setting the Control(s) .................................................................10

Adjusting Control Settings.........................................................10

REFRIGERATOR FEATURES...................................................11

Refrigerator Shelves...................................................................11

Lateral Adjustable Shelf.............................................................11

Meat Drawer and Cover.............................................................12

Chilled Meat Drawer...................................................................12

Crisper and Crisper Cover.........................................................12

Crisper Humidity Control ...........................................................13

Utility or Egg Bin.........................................................................13

Wine or Can/Bottle Rack ...........................................................13

FREEZER FEATURES..............................................................13

Ice Maker....................................................................................13

Freezer Shelf ..............................................................................14

Adjustable Half-width

Freezer Shelf ..............................................................................14

Pull-out Freezer Floor.................................................................14

DOOR FEATURES.................................................................... 15

Door Rails...................................................................................15

Door Bins....................................................................................15

Can Rack....................................................................................15

Adjustable Utility Compartment & Tray .....................................15

Flip-up Door Shelf......................................................................15

CARING FOR YOUR REFRIGERATOR ...................................16

Cleaning Your Refrigerator.........................................................16

Changing the Light Bulbs...........................................................16

Power Interruptions....................................................................16

Vacation and Moving Care.........................................................17

TROUBLESHOOTING............................................................... 17

ASSISTANCE OR SERVICE .................................... ...... ..... ......19

WARRANTY ............................................................................. 20

SÉCURITÉ DU RÉFRIGÉRATEUR...........................................21

INSTALLATION DU RÉFRIGÉRATEUR ...................................22

Déballage de votre réfrigérateur ................................................22

Espacement requis.....................................................................22

Spécifications électriques..........................................................23

Raccordement du réfrigérateur à une canalisation d’eau.........23

Grille de la base..........................................................................24

Portes du réfrigérateur :

Démontage, inversion et réinstallation.......................................25

Fermeture et alignement des portes..........................................27

Les bruits de l’appareil que vous pouvez entendre...................27

UTILISATION DU RÉFRIGÉRATEUR.......................................28

Pour s’assurer d’une circulation d’air appropriée......................28

Réglage des commandes..........................................................28

Ajustement des réglages de commande...................................28

CARACTÉRISTIQUES DU RÉFRIGÉRATEUR.........................29

Tablettes du réfrigérateur...........................................................29

Tablette à réglage latéral............................................................30

Tiroir à viande et couvercle........................................................30

Tiroir à viande réfrigéré...............................................................31

Bac à légumes et couvercle.......................................................31

Réglage de l’humidité dans les bacs à légumes.......................31

Casier utilitaire ou oeufrier..........................................................32

Casier à vin ou porte-cannettes.................................................32

CARACTÉRISTIQUES DU CONGÉLATEUR............................32

Machine à glaçons.....................................................................32

Clayette de congélateur.............................................................33

Clayette ajustable demi-largeur

pour congélateur........................................................................33

Plancher de congélateur coulissant...........................................33

CARACTÉRISTIQUES DE LA PORTE......................................34

Tringles dans la porte.................................................................34

Balconnets..................................................................................34

Porte-cannettes..........................................................................34

Compartiment utilitaire et plateau réglables..............................34

Tablette de porte relevable ........................................................34

ENTRETIEN DE VOTRE RÉFRIGÉRATEUR............................35

Nettoyage du réfrigérateur.........................................................35

Remplacement des ampoules d’éclairage................................35

Pannes de courant.....................................................................36

Entretien avant les vacances ou lors d’un déménagement.......36

DÉPANNAGE.............................................................................36

ASSISTANCE OU SERVICE......................................................39

GARANTIE.................................................................................40

REFRIGERATOR

SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or

“WARNING.” These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

precautions:

■

Plug into a grounded 3 prong outlet.

■

Do not remove ground prong.

■

Do not use an adapter.

■

Do not use an extensio n cord.

■

Disco n nect power be fo re se rv ic i n g .

■

Replace all panels before operating.

■

Remove doors from your old refriger a tor.

To reduce the risk of fire, ele ctric shock, or injury when using your refrige r ato r, follow thes e ba s ic

■

Use nonflammable cleaner.

■

Keep flammable mater ia ls an d vapo rs , su ch as gasoline, aw ay from refr iger ato r.

■

Use two or mo re peop le to mov e an d ins ta ll refrigerator.

■

Disconnect power before installing ice maker (on ice maker kit ready models only).

■

Use a sturdy glass when dispensing ice or water (on some models).

SAVE THESE INSTRUCTIONS

Proper Disposal of Y our Old Refrigerator

W ARNING

Suffocation Hazard Remove doors from your old refrigerator. Failure to do so can result in death or

brain damage.

IMPORT ANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous – even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Before you throw away your old refrigerator or freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easi ly

climb inside.

INSTALLING YOUR

REFRIGERATOR

■ Depending on your model, do not remove the white

Styrofoam insert that is located behind the control panel on the ceiling of the refrigerator. The insert is part of the refrigerator and not part of the packing material. If the insert is removed, ice may migrate down from the freezer and cause icicles to form.

Unpacking Y our Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove shelves from the shipping position (shelves are shipped upside down):

IMPORTANT: Do not clean glass shelves with warm water when

they are cold. Shelves may break if exposed to sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small pebble-size pieces. This is nor mal.

NOTE: Glass shelves are heavy. Use special care when removing them to avoid impact from dropping.

1. Grasp the front of the upper shelf with one hand and use the other hand to remove packing material from the shelf area.

2. Lower the front of the upper shelf until shelf hooks can be removed from the shelf supports and pull the shelf forward.

3. Flip the shelf over and insert the rear shelf hooks into the shelf supports. Tilt th e front of shelf up until rear shelf hooks drop into the shelf supports.

4. Lower the front of the shelf and check to make sure that it is securely in position.

Removing packaging materials

■ Remove tape and any labels from your refrigerator before

using (except the model and serial number label). To remove any remaining tape or glue, rub the area briskly

with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry .

■ Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see “Refrigerator Safety” section.

■ On some models, shelves, bins, door shelf rails, and other

feature parts may be packaged in the Int erior FeaturePak. Follow the instructions contained in the package for proper assembly.

IMPORTANT:

■ Depending on your model, do not remove any permanent

instruction labels inside your refrigerator or the Tech Sheet that is fastened behind the base grille.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as floor damage could occur.

Space Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

■ To ensure pro per ventilation for your refrigerator, allow for a .5

in. (1.25 cm) space on each side and at the top.

.5" (1.25 cm)

2" (5.08 cm)

■ If your refrigerator has an ice maker, make sure you leave

some extra space at the back for the water line connections. The refrigerator can be flush against the back wall if you do not have an ice maker installed.

■ If you are installing your refrigerator next to a fixed wall, leave

2 in. (5.08 cm) minimum on each side (depending on your model) to allow for the door to swing open.

NOTE: Do not install the refrigerator near an oven, radiator, or other heat source, nor in a location where the temperature will fall below 55°F (13°C) .

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in

death, fire, or electrical shock.

Before you move your refrigerator i nto its final l ocation, it is important to make sure you have the proper electrical connection:

Recommended gr oun ding met hod

A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be tur ned off by a switch. Do not use an ex tension cord.

Before performing any type of installation, cleaning, or

NOTE:

removing a light bulb, turn the control, (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.

Tools required:

■ Standard screwdriver

■ ⁷⁄₁₆ in. and ¹⁄₂ in. open-end wrenches or two adjustable

wrenches

■ ¹⁄₄ in. nut driver

■ ¹⁄₄ in. drill bit

■ Hand drill or electric drill (properly grounded)

Your refrigerator dealer has a kit available with a

NOTE:

¹⁄₄ in. (6.35 mm) saddle-type shut-off valve, a union, an d copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercingtype or ³⁄₁₆ in. (4.76 mm) saddle valve which reduces water flow and clogs more easily.

Cold water supply

The ice maker water valve contai ns a flow washer which is used as a water pressure regulator. The ice maker needs to be connected to a cold water line with water pressure between 30 and 120 psi. If a problem occurs, ca ll your utility company.

Connecting to water line:

Unplug refrigerator or disconnect power.

Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water. Locate a ½ in. to 1¹⁄₄ in. (12.7 mm to 3.18 cm) vertical COLD

water pipe near the refrigerator.

Horizontal pipe will work, but the following procedure

NOTE:

must be followed: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve.

To determine the length of copper tubing you will need,

measure from connection on lower left rear of refrigerator to water pipe. Add 7 ft. (2.1 m) to allow for moving refrigerator for cleaning. Use ¹⁄₄ in. (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

Using a gr ounded drill, drill a ¹⁄₄ in. hole in the cold water p ipe

you have selected.

Connecting the Refrigerator

to a W ater Source

Read all directions carefully before you begin. IMPORTANT:

■ If operating the refrigerator before installing the water

connection, turn ice maker to th e OFF position to prevent operation without water.

■ All installations must be in accordance with local plumbing

code requirements.

■ Use copper tubing and check for leaks.

■ Install copper tubing on ly in areas where temperatures will

remain above freezing.

■ It may take up to 24 hours for your ice maker to begin

producing ice.

1. Cold Water Pipe

2. Pipe Clamp

3. Copper Tubing

4. Compression Nut

5. Compression Sleeve

6. Shut-Off Valve

7. Packing Nut

Fasten shut-off valve to cold water pipe with pipe clamp. Be

sure outlet end is solidly in the ¹⁄₄ in. drilled hole in the water pipe and that washer is under t he pipe clamp. Tighten packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubi ng , e sp ecially if soft (c o ile d ) copper tubing is used. Now you are ready to connect the copper tubing.

7. Slip compression sleeve and compression nut on copper tubing as show n. Inse rt end of tu bing into o utle t en d sq uar el y as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing into a container or sink, and turn ON main water supply and flush out tubing until water is clear. Turn OFF shut-off valve on the water pipe. Coil copper tubing.

Connecting to refrigerator:

1. Attach the coppe r tube to the va lve inlet us ing a compr ess ion

nut and sleeve as shown . Tighten the compression nut. Do not overtighten. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help prevent damage to the tubing when the refrigerator is pushed back against the wall. Move to step 2.

2. Turn shut-off valve ON. Check for leaks. Tighten any connections (including connections at th e va lve) or nuts tha t leak.

Base Grille

To remove the base grille:

1. Open the refrigerator door.

2. Grasp the grille with both hands.

3. Lift up and tilt the bottom of the grille toward you. NOTE: Do not remove the Tech Sheet that is fastened behind the

grille.

To replace the base grille:

1. Open the refrigerator door.

2. Place upper clips in openings in the metal panel.

3. Roll the grille down toward the refrigerator until it snaps into

place.

1. Tube Clamp

2. Copper Tubing

3. Compression Nut

4. Valve Inlet

3. The ice maker is equipped with a built-in water strainer. If local water conditions require perio dic cleaning or a well is your source of water supply, a second water strainer should be installed in the ¹⁄₄ in. (6.35 mm) water line. Obtain a water strainer from your nearest appliance dealer. Install at either tube connection.

4. Plug in refrigerator or reconnect power.

Refrigerator Doors: Removing, Reversing (optional) and Replacing

TOOLS NEEDED: ⁵⁄₁₆ in. hex-head socket wrench, No. 2 Phillips screwdriver, flat-head screwdriver, ⁵⁄₁₆ in. open-end wrench, flat 2 in. putty knife.

IMPORTANT: Before you begin, turn the refrigerator control OFF, unplug refrigerator or disconnect power. Remove food and any adjustable door or utility bins from doors.

Door Removal &

Replacement

Base Grille

Top Hinge

1. Top Hinge Cover

2. " Hex-Head Hinge Screws

3. Top Hinge

Center Hinge

Door Swing Reversal (optional)

1. Cabinet Hinge Hole Plugs

1. Door Hinge Hole Plug

2 3

1. Flat-Head Handle Screws

2. Freezer Handle

1. Door Handle Sealing Screws

Front View

Side View

1-2

" Hex-Head Hinge

Screws

1-1

1. Center Hinge

2. " Hex-Head Hinge Screws

Bottom Hinge

1. Bottom Hinge

2. " Hex-Head Hinge Screws

1. Door Stop Screw

2. Door Stop

1. Door Handle Screw Cover

6-1

1. Door Handle Seal Screw Front

6-2

1. Flat-Head

Handle Screw

6-3

2. Refrigerator Handle

3. Handle Screw

Door and hinge removal

⁵⁄₁₆

” Hex Head Hinge Screw

Unplug refrigerator or disconnect power.

Open refrigerator door and remove base grille from the

bottom front of the refrigerator (see Base Grille graphi c). Close the refrigerator door and keep both doors closed until

you are ready to lift them free from the cabinet.

Provide additional support f or the doors while the

NOTE:

hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.

Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the freezer door free from the cabinet.

Remove the parts for the center hinge as shown in the Center

Hinge graphic. Lift the refrigerator door free from the cabinet.

Remove the parts for the bottom hing e as shown in the

Bottom Hinge graphic.

IMPORTANT: If you want to reverse your doors so that they open in the opposite direction, follow these steps. If you are not reversing the doors, see “Door and hinge replacement”.

Door reversal (optional)

Door Stop Screw Door Hinge Hole Plug

Door Handle Sealing Screw Cabinet Hinge Hole Plug

Flat-Head Handle Screw Door Handle Screw Cover

Door Handle Seal Screw Front Round-Head Handle Screw

Cabinet

Remove

move them to opposite side (see Graphic 1-1). Remove cabinet hinge hole plugs from cabinet top and move

them to opposite side hinge holes as shown (see Graphi c 1-

2).

Freezer door

Remove freezer handle assembly as shown . Keep all parts

together (see Graphic 2). Remove door hinge hole plug. Move to opposite side as

shown (see Graphic 3). Remove door handle sealing screws. Move to opposite side

of freezer door as shown (see Graphic 4). Remove door stop. Move to opposite side of freezer door as

shown (see Graphic 5). Position freezer handle on opposite side of freezer door.

Assemble handles on door as shown (see Graphic 2). Tighten all screws. Set aside door until hinges and refrigerator

compartment door are in place.

in hex head hinge screws from handle side and

⁵⁄₁₆

Refrigerator door

Remove refrigerator handle bottom trim. For

the handle screw cover (see Graphic 6-1). For trim down as shown (see Graphic 6-2).

Remove refrigerator handle assembly as shown. Keep all

parts together (see Graphic 6-3 ). Remove door hinge hole plug from refrigerator door. Move to

opposite side hinge h ole as shown (see Graphic 3) . Remove door handle sealing screws. Move to opposite side

of refrigerator door as shown (see Graphic 4). Remove door handle seal screw front. Move to opposite side

of refrigerator door as shown (see Graphic 7). Remove door stop. Move to opposite side of refrigerator door

as shown (see Graphic 5). Position refrigerator handle on opposite side of the

refrigerator door as shown (see Graphic 6-3). Drive top two screws in handle first. Align lower portion of handle and drive bottom screw.

Align refrigerator bottom trim. For

handle screw cover (see Graphic 6-1). For into place (see Graphic 6 -2).

Tighten all screws. Set aside refrigerator door until bottom

hinge is instal led on product.

Style 1,

replace the door

Style 2,

slide trim

remove

slide

Door and hinge replacement

Graphic may be reversed if door swing is reversed.

Note:

Replace the parts for the bottom hinge as shown. Tighten

screws. Replace the refrigerator door.

Provide additional support for the doors while the

NOTE:

hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.

Assemble the parts for the center hinge as shown and tighten

all screws (see Center Hinge graphic). Replace the freezer door.

Assemble the parts of the top hinge as shown (see T op Hinge

graphic). Do not tighten screws completely. Line up the doors so that the bot tom of the freezer door

aligns evenly with the top of the refrigerator door. Tighten all screws.

Final Steps

Check all holes to make sure that hole plugs and screws are

in place. Reinstall top hinge cover (see Top Hinge graphic). Replace the base grille (see Base Grille graphic).

Plug in refrigerator or reconnect power.

Reset the controls (see “Setting the Controls” section).

Return all removable door parts to doors and food to product.

Door Closing and Alignment

Door Closing

Your refr igerat or has two fr ont a djustab le r ollers – one on the rig ht and one on the left. If your refrigerator seems unsteady or you want the doors to close easier, adjust the refrigerator's tilt using the instructions below:

Plug refrigerator power cord into a 3 prong grounded outlet.

Move the refrigerator into its fi nal position. Remove the base grille (see “Base Grille” earlier in this

section). The two leveling screws are part of the front roller assemblies which are at the base of the refrigerator on either side.

3. Use a screwdriver to adjust the leveling screws. Turn the leveling scr e w to the right to raise that sid e of the refrigerator or turn the leveling screw to the left to lower that side. It may take several turns of the leveling screws to adjust the tilt of the refrigerator.

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws and rollers. This makes it easier to adjust the screws.

■ You may hear the evaporator fan motor circulating the air

through the refrigerator and freezer compartments.

■ As each cycle ends, you may hear a gu rgling sound due to

the refrigerant flowing in your refrigerator.

■ Contraction and expansion of the inside walls may cause a

popping noise.

■ You may hear air being forced over the condenser by the

condenser fan.

■ You may hear water runnin g into the drain pan during the

defrost cycle.

USING YOUR

REFRIGERATOR

4. Open both doors again and check to make sure that they close as easily as you like. If not, tilt the refrigerator slightly more to the r ear by turning both l eveling sc rew s to the righ t. It may take several more turns, and you should turn both leveling screws the same amount.

5. Replace the base grille.

Door Alignment

If the space between your doors looks uneven, you can adjust it using the instructio n s be low:

1. Pry off the top hinge cover.

2. Loosen the top hinge screws using a ⁵⁄₁₆-inch socket or

wrench.

3. Have someone hold the door in place or put a spacer between the doors while you tighten the top hinge screws.

4. Replace the top hinge cov e r.

Understanding Sounds Y ou May Hear

Your new refrigerator may make sounds that your old one didn’t make. Because the sounds are new to you, you might be concerned about them. Most of the new sounds are normal. Hard surfaces, like the floor , walls, and cabinets, can make the sounds seem louder than they actually are. The following describes the kinds of sounds and what may be making them.

■ If your product is equipped with an ice maker, you will hear a

buzzing sound when the water valve opens to fill the ice maker for each cycle.

■ The defrost timer will click when the automatic defrost cycle

begins and ends. Also, the Thermostat Control (or Refrigerator Control depending on the model) will click when cycling on and off.

■ Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.

■ Your refrigerator is designed to run more efficiently to keep

your food items at the desired temperature. The high efficiency compressor may cause your new refrigerator to run longer than your old one, and you may hear a pulsating or high-pitched sound.

■ Water dripping on the defrost heater during a defrost cycle

may cause a sizzling sound.

Ensuring Proper Air Circulation

In order to ensure proper temperatures, you need to permit airflow between the refrigerator and freezer sections. As shown in the illustration, cool air enters through the bottom of the freezer section and moves up. Most of the air then flows through the freezer section vents and recirculates under the freezer floor. The rest of the air enters the refrigerator section through the top vent.

Do not block any of these vents with food packages. If the vents are blocked, airflow will be prevented and temperature and moisture problems may occur.

IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To prevent odor transfer and drying out of food, wrap or cover foods tightly.

Setting the Control(s)

For your convenience, the refrigerator controls are preset at the factory. Controls for the refrigerator and freezer are located

in the top of the refrigerator section.

When you first install your refrigerator, make sure that the control(s) are still preset. The control(s) should be at the “mid-settings” as shown for each style of control.

Mid-setting “3”

WARMER

REFRIGERATOR

RECOMMENDED SETTINGRECOMMENDED SETTING

4 5

COLDER

WARMER

FREEZER

RECOMMENDED SETTINGRECOMMENDED SETTING

COLDER

1 2

4 5

Adjusting Control Settings

Give the refrigerator time to co o l do w n co m p le tely before adding food. It is best to wait 24 hours before you put food into the refrigerator. The “mid-settings” indicated in the previous secti on should be correct for normal household refrigerator usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.

For models with two controls:

The Refrigerator Control functions as the thermostat for the entire product (refrigerator and freezer sections). The higher the number setting, the longer the compressor will run to keep the temperature colder. The Freezer Control adjusts the cold air flow from the freezer to the refrigerator.

If you need to adjust temperatures in the refrigerator or freezer, start by adjusting the refrigerator first. Wait 24 hours after the refrigerator adjustment to check the freezer temperature. If it is too warm or too cold, then adjust the Freezer Control as well.

For models with a single control:

The Temperature Control functions as the thermostat for the entire product (refrigerator and freezer sections). The higher t he number setting, the longer the compressor will run to keep the temperature colder.

Use the settings listed in the chart below as a guide. Always

remember to wait at least 24 hours between adjustments.

Mid-setting “4”

REFRIGERATOR

FREEZER

NOTE: To turn your r e frig era tor o f f, turn the refriger ato r con tr o l to the word OFF or until the word OFF appears, as shown below. Your product will not cool when the refrigerator control is set to OFF.

REFRIGERATOR

OFF

WARMER

REFRIGERATOR

RECOMMENDED SETTING

4 5

COLDER

Give your refrigerator time to cool down completely before adding food. It is best to wait 24 hours before you put food into the refrigerator.

IMPORTANT: If you add food before the refrigerator has cooled completely, your foo d may spoil. Turning the Refrigerator or

Freezer Control(s) to a higher (colder) than recommended setting will not cool the compartments any faster.

On models with t wo controls, the F r e e ze r C on trol functions a s an airflow director . Setting “1” will direct more of the cold air into the refrigerator section, while setting “5” (or “7” depending on your model) will d ir ect mor e of the cold air into th e f re eze r se ction . Th e cold air flows from the freezer compartment through the top vent into your fre sh food s ect io n ( s ee d ia gra m in the "En su ring Proper Air Circulation" section). On models with one control, the airflow does not require adjustment.

CONDITION/REASON:

REFRIGERATOR section too warm

■ Door opened often

■ Large amount of food added

■ Room temperature very warm

■ Blocked air stream

FREEZER section too warm/ice not made fast enough

■ Door opened often

■ Large amount of food added

■ Very cold room tem per a ture (can’t

cycle often enough)

■ Heavy ice usage

■ Blocked air stream

RECOMMENDED ADJUSTMENT:

Turn REFRIGERATOR Control or TEMPERATURE Control to next higher number, wait 24 hours, then recheck

Move items out of air stream

Turn FREEZER Control or TEMPERATURE Control to next higher number, wait 24 hours, then recheck

Move items out of air stream

CONDITION/REASON:

REFRIGERATOR section too cold

■ Controls not set correctly for your

conditions

■ Blocked air stream

FREEZER section too cold

■ Controls not set correctly for your

conditions

RECOMMENDED ADJUSTMENT:

Turn REFRIGERATOR Control or TEMPERATURE Control to next lower number, wait 24 hours, then recheck

Move items out of air stream

Turn FREEZER Control or TEMPERATURE Control to next lower number, wait 24 hours, then recheck

To remove and replace a shelf in a metal frame:

1. Pull the shelf forward to the stop .

2. Tilt the front of the shelf up and lift it slightly as you pull the

shelf from the frame.

3. Replace the shelf by guiding it back into the slots on the frame and pushing the shelf in past the stop.

Shelves a nd Shel f Fram es

To remove and replace a shelf/frame:

1. Remove the sh elf /fram e by t iltin g it u p at th e fr ont and l iftin g it

out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into the shelf suppo rts . Ti lt the front of the shelf up until r ear sh el f hooks drop into the shelf supports.

3. Lower the front of the shelf and check to make sure that the shelf is securely in position.

■ Blocked air stream

Move items out of air stream

REFRIGERATOR

FEATURES

Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word “Accessory.” Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please call the toll-free number on the cover or in t he "Assistance or Service" section.

Refrigerator Shelves

The shelves in your refrigerat or are adjustable to meet your individual storage need s. Your model may have glass or wire shelves.

Storing similar food items together in your refrigerator and adjusting the shelves to fit different heights of items will make finding the exact item you want easier. It will also reduce the amount of time the refrigerator door is open, and save energy.

IMPORTANT: Do not clean glass shelves with warm water when they are cold. Shelves may break if exposed to sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small pebble-size pieces. This is nor mal.

NOTE: Glass shelves are heavy. Use special care when removing them to avoid impact from dropping.

Slide-out Shelves (on some models)

■ To slide out shelf, carefully pull front of shelf toward you.

■ To slide in shelf, push shelf in until it stops.

Lateral Adjustable Shelf

(on some models)

To slide the shelf from side to side:

1. Lift up on the front of shelf and slide to the desired location.

2. Lower shelf to the level position.

NOTE: You do not have to remove small items from the shelf

before moving it from side to side. You may need to remove larger items.

To remove the shelf: NOTE: The shelf is heavy and must be removed using both

hands.

1. Hold the back of the shelf with one hand .

2. Lift the front of the shelf with the other hand to a 45° angle

and lower it slightly t o rele ase it fr om th e upper chan nel of the track. Pull the shelf straight out.

To remove and replace the shelf track:

COLDER

COLD

LOWLOW

HIGHHIGH

1. Remove the shelf track by lifting both sides of the track slightly and pulling the track straight out.

2. Replace the track by guiding the track hooks into the shelf support slots on the back wall.

NOTE: Make sure that both sets of track hooks are in the slots and that the slots are parallel with each other.

3. Push the track back and do wn securely into the shelf supports.

To replace the shelf: NOTE: Make sure that both of the rear shelf slides are securely in

the track before letting go of the shelf. The lateral shelf may be difficult to install if the track is placed too close to the refrigerator ceiling. Reposition the track on a lower rung until the shelf can be tilted enough to easily slide into the track.

1. Hold the shelf at the front and tip the front at a 45° angle to the track.

2. Insert both of the rear shelf slides into the upper channel of the track, and lower the front of the shelf into place.

Meat Drawer and Cover

(on some mo dels)

To remove and replace the meat drawer (all styles):

1. Remove the meat drawer by sliding it out to the stop. Lift the

front of meat drawer with one hand while supporting the bottom of drawer with other hand. Slide drawer out the rest of the way.

2. Replace the meat drawer by guiding it into the meat cover supports and pushing it in until it stops.

To remove and replace the meat drawer cover (Style 1 glass):

1. Remove the meat drawer. Remove the cover by tilting up the

front of the cover and lifting at the back. Pull the cover straight out.

2. Replace the cover by guiding the rear hooks into the shelf supports. Tilt the cover up at the front until the rear hooks drop into the slots.

3. Lower the front of the cover to a level position and replace the meat drawer.

IMPORTANT: Do not clean glass meat drawer covers with warm water when they are cold. Glass meat drawer covers may break if exposed to sudden temperatu re changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small pebble-size pieces. This is normal.

NOTE: Glass meat drawer covers are heavy. Use special care when removing them to avoid impact from dropping.

3. Lower cover into place and replace the meat drawer.

Chill ed Meat Draw er

(on some models)

To adjust the meat drawer temperature:

■ Slide the meat drawer temperature control forward to make

the meat drawer less cold.

■ Slide the meat drawer temperature control backward to make

the meat drawer colder.

Meat stor age gui de

Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following chart for storage times. When storing meat longer than the times given, freeze the meat.

Fresh fish or shellfish..................use same day as purchased

Chicken......................... ..... ...... .................................1-2 days

Ground beef..............................................................1-2 days

Variety meats (liver, heart, etc.)..................................1-2 days

Cold cuts...................................................................3-5 days

Steaks/roasts................ ..... ...... ..... ............................3-5 days

Cured meats............................................................7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or plastic containers wi th tight lids.

Crisper and Crisper Cover

(on some models - Accessory)

To remove and replace the crisper(s):

1. Slide crisper(s) straight out to the stop. Lift the front of the

crisper(s) and slide out the rest of the way.

2. Replace the crisper(s) by sliding back in full y past the drawer stop.

To remove and replace the meat drawer cover (Style 2 plastic):

1. Remove the meat drawer. Tilt the cover up at the front and

pull it forward and out.

2. Replace the meat drawer cover by fitting the notches and rear edge of the cover over rear and center crossbars on the shelf.

IMPORTANT: Do not clean glass crisper covers with warm water when they are cold. Glass crisper covers may break if exposed to sudden temperature changes or impact, such as bumping. For your protection tempered glass is designed to shatter into many small pebble-size pieces. This is normal.

+ 28 hidden pages