WHILL LISAU200 Users Manual
C
ONTROL PAD
U
SER MANUAL
320-07058-DHF.DO-01
Doc #
Rev 1
1 Understanding the Control Pad for WHILL Model Ci
1.1 Product Information
• Product name: Control pad
• Model name: IC_Assy_3GUS
• Part number: 210-06836
• Contains
o Module name: WHILL-LISA-U200-3G
o FCC ID: 2AN6FLISAU200
o IC: 23338-LISAU200N
• Manufacturer:
WHILL, Inc.
285 Old County Road, Suite 6, San Carlos, CA 94070
(844) 699-4455
This product comes installed on your WHILL Model Ci and is available for use as is on the Model Ci without any additional set up. In
addition to providing handy controls, it allows the Model Ci to communicate wirelessly with other devices. Please refer to the WHILL
Model Ci user manual supplied in the same packaging for detailed safety information and instructions for use.
[47 CFR 2.1077]
1.2 Technical Specifications
Operating and storage temperature range:
Dimensions (width x height x length): 2.0 x 4.6 x 4.8 inches (51 x 117.6 x 122 mm)
Weight: 9.5 oz (270 g)
5°F~104°F (-15
℃
～40℃
)
1.3 Appearance
Please see component E in Section 2.2. of the WHILL Model Ci user manual for an image of the control pad.
1.4 Accessing the FCC/IC Regulatory Label on the Control Pad
The control pad is labelled with an FCC ID (Federal Communications Commission identifier) and an ISED certification number
(Innovation, Science and Economic Development Canada certification number). The label is accessible without the use of tool by
removing the round cover on the control pad as shown in Step 3 from Section 5.3.2. of the WHILL Model Ci user manual.
2 Regulatory Information
2.1 Federal Communications Commission (FCC) Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the
emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.
RF exposure warning
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for
satisfying RF exposure compliance.
[47 CFR 2.1077, 15.19]
[47 CFR 15.105]
[47 CFR 15.21]
Page 1 of 2
C
ONTROL PAD
U
SER MANUAL
320-07058-DHF.DO-01
Doc #
Rev 1
2.2 Industry Canada (IC) Information
This Class B device complies with CAN ICES-3 (B)/NMB-3(B). This device complies with Canada licence-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Cet appareil de la classe B est conforme avec CAN ICES-3 (B)/NMB-3(B). Cet appareil est conforme avec Industrie Canada exemptes de
licence RSS standard(s). Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer d'interférence et (2)
cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device
should be used in such a manner such that the potential for human contact during normal operation is minimized.
This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are
greater than 20cm from a person's body).
Informations concernant l'exposition aux fréquences radio (RF)
La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez
l’appareil de sans fil de façon à minimiser les contacts humains lors du fonctionnement normal.
Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition à des
appareils mobiles (antennes sont supérieures à 20 cm à partir du corps d'une personne).
Page 2 of 2
Loading...