Whelen WS321B9 User Manual

®

ENGINEERING COMPANY INC.

51 Winthrop Road,

Chester, Connecticut 06412-0684

Phone: [phone]

Fax: [phone]

Installation:

1. Hook the top of the bracket over the top of the crash bar as
shown in figure 1.

2. Secure the top of the bracket with the supplied bolt, flat washer
and spacer in the order shown (Fig. 2).

3. Slip the loop clamp around the bottom of the crash bar and
secure the bottom of the bracket to the loop clamp with the
supplied wing screw and flat washer (Fig. 2).

4. Secure the siren to the bracket with the 4 bolts included with the
siren (Fig. 2).

5. Make sure all hardware is tightened firmly and extend the siren
wires to their power source (Refer to the sirens instructions for
hookup and voltage).

IMPORTANT! It is the responsibility of the installation

technician to make sure that the installation and operation of
this product will not interfere with or compromise the operation
or efficiency of any vehicle equipment!

IMPORTANT! Before returning the vehicle to active service,

visually confirm the proper operation of this product, as well as
all vehicle components/equipment.

Installation Guide:

Harley-Davidson® Crash Bar Mounting Bracket

for the Model WS321 Siren Amplifier

Internet: www.whelen.com
Sales e-mail: [e-mail]
Canadian Sales e-mail: [e-mail]
Customer Service e-mail: [e-mail]

Fig. 1

Automotive: Sirens & Switches

©2009 Whelen Engineering Company Inc.
Form No.14276 (031909)

For warranty information regarding this product, visit www.whelen.com/warranty

ENGINEERING COMPANY INC.

51 Winthrop Road,

Chester, Connecticut 06412-0684

Phone: [phone]

Fax: [phone]

Installation:

1. Hook the top of the bracket over the top of the crash bar as
shown in figure 1.

2. Secure the top of the bracket with the supplied bolt, flat washer
and spacer in the order shown (Fig. 2).

3. Slip the loop clamp around the bottom of the crash bar and
secure the bottom of the bracket to the loop clamp with the
supplied wing screw and flat washer (Fig. 2).

4. Secure the siren to the bracket with the 4 bolts included with the
siren (Fig. 2).

5. Make sure all hardware is tightened firmly and extend the siren
wires to their power source (Refer to the sirens instructions for
hookup and voltage).

IMPORTANT! It is the responsibility of the installation

technician to make sure that the installation and operation of
this product will not interfere with or compromise the operation
or efficiency of any vehicle equipment!

IMPORTANT!Before returning the vehicle to active service,
visually confirm the proper operation of this product, as well as
all vehicle components/equipment.

®

Installation Guide:

Harley-Davidson® Crash Bar Mounting Bracket

for the Model WS321 Siren Amplifier

Internet: www.whelen.com
Sales e-mail: [e-mail]
Canadian Sales e-mail: [e-mail]
Customer Service e-mail: [e-mail]

Fig. 1

Automotive: Sirens & Switches

©2009 Whelen Engineering Company Inc.
Form No.14276 (031909)

For warranty information regarding this product, visit www.whelen.com/warranty

Page 1

Fig. 2

REAR
VIEW

C

R

A

7/8 LOOP

S

H

B

A

CLAMP

5/16 FLATWASHER

R

5/16 - 18 X 1-1/4
HEX HD BOLT

SPACER

CRASH

5/16 - 18 X 3/4"
WING SCREW

5/16 FLAT

WASHER

BAR

SIREN AMPLIFIER

Siren
mounting
screws
(Qty 4)

FRONT

of BIKE

Fig. 2

REAR
VIEW

C

R

A

S

H

B

A

R

5/16 FLATWASHER

SPACER

5/16 - 18 X 1-1/4
HEX HD BOLT

CRASH

5/16 - 18 X 3/4"
WING SCREW

5/16 FLAT

WASHER

BAR

SIREN AMPLIFIER

Siren
mounting
screws
(Qty 4)

FRONT

of BIKE

7/8 LOOP

CLAMP

Page 2