How it Works
Whelen
Loading...
SK02JJ
User Manual
2 pgs278.22 Kb0

Whelen SK02JJ User Manual

GND
SYNC
SCANLOCK
BLACK ­GREY ­WHT/VIO -
- +12VSolid Lighthead: LED COLOR
LIGHTHEAD
To Ground Terminal
To SYNC wire of other light
Flash Pattern Selection
To +12 Volts VDC
Fuse @ 3 AMPS / Customer supplied
NOTE: The positive wire will vary depending upon which lighthead you have.
6 - 32 X 5/16 PHX WASHER HEAD SCREW (2)
Fig. 1
Remove vent cover
®
ENGINEERING COMPANY INC.
GND
SYNC
SCANLOCK
BLACK ­GREY ­WHT/VIO -
- +12VSolid Lighthead: LED COLOR
LIGHTHEAD
To Ground Terminal
To SYNC wire of other light
Flash Pattern Selection
To +12 Volts VDC
Fuse @ 3 AMPS / Customer supplied
NOTE: The positive wire will vary depending upon which lighthead you have.
6 - 32 X 5/16 PHX WASHER HEAD SCREW (2)
Fig. 1
Remove vent cover
®
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Installation Guide:
SideKick™ Super-LED® Fender Lights
2011 - 2012 Chevrolet Caprice
Internet: www.whelen.com Sales e-mail: autosale@whelen.com Canadian Sales e-mail: canadiansales@whelen.com Customer Service e-mail: custserv@whelen.com
Installation 2011 - 2012 Chevrolet Caprice:
1. Remove the vent panel following manufacturers instructions (Fig. 1).
2. Install the ION™ lighthead into the SideKick™ panel using the 2 supplied screws.
3. Extend the lighthead wires to your power source and snap the panel into the vent panel opening.
Connecting the Lighthead to Power:
Route the lighthead wires along the same path as the vehicle’s main power cable and connect
to power.
WARNING: All customer supplied wires that connect to the positive terminal of the battery must be sized to supply at least 125% of the maximum operating current and FUSED at the battery to carry that load. DO NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT!
Automotive: Lightheads
©2012 Whelen Engineering Company Inc. Form No.14574 (032612)
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Automotive: Lightheads
©2012 Whelen Engineering Company Inc. Form No.14574 (032612)
For warranty information regarding this product, visi85ww.whelen.com/warranty
Installation Guide:
SideKick™ Super-LED® Fender Lights
2011 - 2012 Chevrolet Caprice
Internet: www.whelen.com Sales e-mail: autosale@whelen.com Canadian Sales e-mail: canadiansales@whelen.com Customer Service e-mail: custserv@whelen.com
Installation 2011 - 2012 Chevrolet Caprice:
1. Remove the vent panel following manufacturers instructions (Fig. 1).
2. Install the ION™ lighthead into the SideKick™ panel using the 2 supplied screws.
3. Extend the lighthead wires to your power source and snap the panel into the vent panel opening.
Connecting the Lighthead to Power:
Route the lighthead wires along the same path as the vehicle’s main power cable and connect
to power.
WARNING: All customer supplied wires that connect to the positive terminal of the battery must be sized to supply at least 125% of the maximum operating current and FUSED at the battery to carry that load. DO NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT!
Page 1
For warranty information regarding this product, visit www.whelen.com/warranty
CAUTION! DO NOT LOOK DIRECTLY AT THESE LED’S WHILE THEY ARE ON. MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT!
IMPORTANT WARNING!
Flash Patterns / Split LED:
BOLD . /NOTE: = CA Title XIII Compliant Pattern = SYNC PatternItalic / PH = Phase
1. SignalAlert™ 75 (PH 1)
2. SignalAlert 75 (PH 2)
3. SignalAlert 75 (PH 3)
4. SignalAlert 75 (PH 4)
5. CometFlash® 75 (PH 1)
6. CometFlash 75 (PH 2)
7. CometFlash 75 (PH 3)
8. CometFlash 75 (PH 4)
17. ComAlert™ 75 (PH 1)
18. ComAlert 75 (PH 2)
19. ComAlert 75 (PH 3)
20. ComAlert 75 (PH 4)
21. LongBurst™ 75 (PH 1)
22. LongBurst 75 (PH 2)
23. LongBurst 75 (PH 3)
9. DoubleFlash 75 (PH 1)
10. DoubleFlash 75 (PH 2)
11. DoubleFlash 75 (PH 3)
12. DoubleFlash 75 (PH 4)
13. SingleFlash 75 (PH 1)
14. SingleFlash 75 (PH 2)
15. SingleFlash 75 (PH 3)
16. SingleFlash 75 (PH 4)
24. LongBurst 75 (PH 4)
29. SSNF 75 (PH 1)
30. SSNF 75 (PH 2)
25. PingPong™ 75 (PH 1)
26. PingPong 75 (PH 2)
27. PingPong 75 (PH 3)
28. PingPong 75 (PH 4)
31. SingleFlash 60 (Alt.)
32. SingleFlash 60 (Sim.) SingleFlash ( SingleFlash 0 (Sim.)
35. SingleFlash 120 (Alt.)
36. SingleFlash 120 (Sim.)
SingleFlash 300 (Alt.)
38. SingleFlash 300 (Sim.) DoubleFlash 150 (Alt.)
40. DoubleFlash 150 (Sim.)
41. ComAlert™ 150 (Alt.)
42. ComAlert™ 150 (Sim.)
43. ActionFlash™ 50 (Alt.)
44. ActionFlash™ 50 (Sim.)
45. ActionFlash™ 150 (Alt.)
46. ActionFlash™ 150 (Sim.)
33. 90 Alt.)
34. 9
37.
39.
47. ModuFlash™ (Alt.)
48. ModuFlash™ (Sim.)
64. ActionScan™ (Alt./Sim.)
49. DoubleFlash 120 (Alt.)
50. DoubleFlash 120 (Sim.)
51. PingPong™ 120 (Alt.)
52. PingPong 120 (Sim.)
53. TripleFlash™ 75 (Alt.)
54. TripleFlash 75 (Sim.)
55. TripleFlash 120 (Alt.)
56. TripleFlash 120 (Sim.)
57. SigAlert Cal.™ (Alt.)
58. SigAlert Cal. (Sim.)
59. Action SF 60/120 (Alt.)
60. Action SF 60/120 (Sim).
61. Action SF60/TF120 (Alt.)
62. Action SF60/TF120 (Sim.)
63. CalScan™ (Alt./Sim.)
65. SteadyFlash 60
66. SteadyFlash 75
67. SteadyFlash 90
68. SteadyFlash 120
69. Steady & Steady
SingleFlash 75PH 2
PingPong™ 75PH 1 PingPong 75PH 2
ComAlert™ 75PH 1 ComAlert 75PH 2 LongBurst™ 75PH 1 LongBurst 75PH 2
8.
9.
10.
11.
12.
13.
14.
SingleFlash 60 SingleFlash
SingleFlash 120
SingleFlash 300 DoubleFlash 150 ComAlert™ 150 ActionFlash™ 50
90
ActionFlash™ 150 ModuFlash™ ActionScan™
Steady
15.
17. 18 1
20.
21.
16.
.
9.
22.
23.
24.
25.
SignalAlert™ 75PH 1 SignalAlert 75PH 2 CometFlash® 75PH 1 CometFlash 75PH 2
DoubleFlash 75PH 1 DoubleFlash 75PH 2 SingleFlash 75PH 1
1.
2.
3.
4.
5.
6.
7.
Flash Patterns / Regular LED:
Operation:
CAUTION! DO NOT LOOK DIRECTLY AT THESE LED’S WHILE THEY ARE ON. MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT!
IMPORTANT WARNING!
Flash Patterns / Split LED:
BOLD . /NOTE: = CA Title XIII Compliant Pattern = SYNC PatternItalic / PH = Phase
1. SignalAlert™ 75 (PH 1)
2. SignalAlert 75 (PH 2)
3. SignalAlert 75 (PH 3)
4. SignalAlert 75 (PH 4)
5. CometFlash® 75 (PH 1)
6. CometFlash 75 (PH 2)
7. CometFlash 75 (PH 3)
8. CometFlash 75 (PH 4)
17. ComAlert™ 75 (PH 1)
18. ComAlert 75 (PH 2)
19. ComAlert 75 (PH 3)
20. ComAlert 75 (PH 4)
21. LongBurst™ 75 (PH 1)
22. LongBurst 75 (PH 2)
23. LongBurst 75 (PH 3)
9. DoubleFlash 75 (PH 1)
10. DoubleFlash 75 (PH 2)
11. DoubleFlash 75 (PH 3)
12. DoubleFlash 75 (PH 4)
13. SingleFlash 75 (PH 1)
14. SingleFlash 75 (PH 2)
15. SingleFlash 75 (PH 3)
16. SingleFlash 75 (PH 4)
24. LongBurst 75 (PH 4)
29. SSNF 75 (PH 1)
30. SSNF 75 (PH 2)
25. PingPong™ 75 (PH 1)
26. PingPong 75 (PH 2)
27. PingPong 75 (PH 3)
28. PingPong 75 (PH 4)
31. SingleFlash 60 (Alt.)
32. SingleFlash 60 (Sim.) SingleFlash ( SingleFlash 0 (Sim.)
35. SingleFlash 120 (Alt.)
36. SingleFlash 120 (Sim.)
SingleFlash 300 (Alt.)
38. SingleFlash 300 (Sim.) DoubleFlash 150 (Alt.)
40. DoubleFlash 150 (Sim.)
41. ComAlert™ 150 (Alt.)
42. ComAlert™ 150 (Sim.)
43. ActionFlash™ 50 (Alt.)
44. ActionFlash™ 50 (Sim.)
45. ActionFlash™ 150 (Alt.)
46. ActionFlash™ 150 (Sim.)
33. 90 Alt.)
34. 9
37.
39.
47. ModuFlash™ (Alt.)
48. ModuFlash™ (Sim.)
64. ActionScan™ (Alt./Sim.)
49. DoubleFlash 120 (Alt.)
50. DoubleFlash 120 (Sim.)
51. PingPong™ 120 (Alt.)
52. PingPong 120 (Sim.)
53. TripleFlash™ 75 (Alt.)
54. TripleFlash 75 (Sim.)
55. TripleFlash 120 (Alt.)
56. TripleFlash 120 (Sim.)
57. SigAlert Cal.™ (Alt.)
58. SigAlert Cal. (Sim.)
59. Action SF 60/120 (Alt.)
60. Action SF 60/120 (Sim).
61. Action SF60/TF120 (Alt.)
62. Action SF60/TF120 (Sim.)
63. CalScan™ (Alt./Sim.)
65. SteadyFlash 60
66. SteadyFlash 75
67. SteadyFlash 90
68. SteadyFlash 120
69. Steady & Steady
SingleFlash 75PH 2
PingPong™ 75PH 1 PingPong 75PH 2
ComAlert™ 75PH 1 ComAlert 75PH 2 LongBurst™ 75PH 1 LongBurst 75PH 2
8.
9.
10.
11.
12.
13.
14.
SingleFlash 60 SingleFlash
SingleFlash 120
SingleFlash 300 DoubleFlash 150 ComAlert™ 150 ActionFlash™ 50
90
ActionFlash™ 150 ModuFlash™ ActionScan™
Steady
15.
17. 18 1
20.
21.
16.
.
9.
22.
23.
24.
25.
SignalAlert™ 75PH 1 SignalAlert 75PH 2 CometFlash® 75PH 1 CometFlash 75PH 2
DoubleFlash 75PH 1 DoubleFlash 75PH 2 SingleFlash 75PH 1
1.
2.
3.
4.
5.
6.
7.
Flash Patterns / Regular LED:
Scan-Lock™ (WHT/VIO) - Note: The light must be on to change patterns.
To advance to next pattern: Apply +VDC to the WHT/VIO wire for less than 1
second.
To cycle backwards: Apply +VDC to the WHT/VIO wire for more than 1 second.
To reset to the factory default pattern: Turn off power to the light. While applying
+VDC to the WHT/VIO wire, turn the light back on. Continue to apply voltage for 5 seconds.
SYNC (GREY) - Lights configured to display the Phase 1 mode of a pattern will flash simultaneously. Lights configured to display the Phase 2 mode will alternate with any Phase 1 lights with the same pattern.
To sync two lights, configure both lights to display the same Phase 1 pattern. Turn power off and connect the GREY wires from each light together. When the lights are activated, their patterns will be synchronized. To configure the two lights to alternate their patterns, advance the pattern of either lights to Phase 2 of the current pattern. The same concept applies to Phases 3 and 4.
IMPORTANT: It is the responsibility of the installation technician to make sure that the installation and operation of this product will not interfere with or compromise the operation or efficiency of any vehicle equipment!
Operation:
Scan-Lock™ (WHT/VIO) - Note: The light must be on to change patterns.
To advance to next pattern: Apply +VDC to the WHT/VIO wire for less than 1
second.
To cycle backwards: Apply +VDC to the WHT/VIO wire for more than 1 second.
To reset to the factory default pattern: Turn off power to the light. While applying
+VDC to the WHT/VIO wire, turn the light back on. Continue to apply voltage for 5 seconds.
SYNC (GREY) - Lights configured to display the Phase 1 mode of a pattern will flash simultaneously. Lights configured to display the Phase 2 mode will alternate with any Phase 1 lights with the same pattern.
To sync two lights, configure both lights to display the same Phase 1 pattern. Turn power off and connect the GREY wires from each light together. When the lights are activated, their patterns will be synchronized. To configure the two lights to alternate their patterns, advance the pattern of either lights to Phase 2 of the current pattern. The same concept applies to Phases 3 and 4.
IMPORTANT: It is the responsibility of the installation technician to make sure that the installation and operation of this product will not interfere with or compromise the operation or efficiency of any vehicle equipment!
Page 2
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use