Whelen SK01AA User Manual
View from Outside of the Fender
8 - 32 X 1/2" PHILLIPS
PAN HEAD METAL SCREW
Fig. 1
INSERT FRONT OF HOUSING.
MOUNTING CLIP MUST CATCH
INSIDE EDGE OF BODY.
®
ENGINEERING COMPANY INC.
INSTALL
CLIP NUT
View from Outside of the Fender
8 - 32 X 1/2" PHILLIPS
PAN HEAD METAL SCREW
Fig. 1
INSERT FRONT OF HOUSING.
MOUNTING CLIP MUST CATCH
INSIDE EDGE OF BODY.
®
INSTALL
CLIP NUT
View from the Inside of the Fender
Fig. 2
MOUNTING CLIP MUST REST
ON INSIDE EDGE OF BODY
OPENING
6 - 32 X 5/16 WASHER HD SCREW
(LIGHTHEAD TO BRACKET)
SECURE REAR OF
HOUSING TO CLIP
NUT
View from the Inside of the Fender
Fig. 2
MOUNTING CLIP MUST REST
ON INSIDE EDGE OF BODY
OPENING
6 - 32 X 5/16 WASHER HD SCREW
(LIGHTHEAD TO BRACKET)
SECURE REAR OF
HOUSING TO CLIP
NUT
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Installation:
1. Remove the vent panel from the vehicle per
manufacturers instructions and install the
supplied clip nut onto the fender on the vent rear
mounting hole.
2. Install the ION™ lighthead into the SideKick™
panel using the 2 supplied washer head screws
(Fig. 2).
Installation Guide:
SideKick™ Super-LED® Fender Lights
2012 - 2013 Ford Police Interceptor Sedan
Internet: www.whelen.com
Sales e-mail: autosale@whelen.com
Canadian Sales e-mail: canadiansales@whelen.com
Customer Service e-mail: custserv@whelen.com
3. Extend the lighthead wires into the fender to the power source and
install the SideKick™ panel by first inserting the front into the fender
opening so that the 2 mounting clips on the SideKick™ grab the
inside of the fender (Figs. 1 & 2).
4. Next swing the rear of the SideKick™ toward the fender so that the
rear mounting hole lines up with the clip nut you installed and secure
it with the supplied 8 - 32 X 1/2” Phillips Pan Head Metal Screw.
IMPORTANT: It is the responsibility of the installation
technician to make sure that the installation and operation of
this product will not interfere with or compromise the operation
or efficiency of any vehicle equipment!
Automotive: Lightheads
©2012 Whelen Engineering Company Inc.
Form No.14577 (033012)
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
For warranty information regarding this product, visi85ww.whelen.com/warranty
Installation Guide:
SideKick™ Super-LED® Fender Lights
2012 - 2013 Ford Police Interceptor Sedan
Internet: www.whelen.com
Sales e-mail: autosale@whelen.com
Canadian Sales e-mail: canadiansales@whelen.com
Customer Service e-mail: custserv@whelen.com
3. Extend the lighthead wires into the fender to the power source and
install the SideKick™ panel by first inserting the front into the fender
opening so that the 2 mounting clips on the SideKick™ grab the
inside of the fender (Figs. 1 & 2).
4. Next swing the rear of the SideKick™ toward the fender so that the
rear mounting hole lines up with the clip nut you installed and secure
it with the supplied 8 - 32 X 1/2” Phillips Pan Head Metal Screw.
IMPORTANT: It is the responsibility of the installation
technician to make sure that the installation and operation of
this product will not interfere with or compromise the operation
or efficiency of any vehicle equipment!
Automotive: Lightheads
Installation:
1. Remove the vent panel from the vehicle per
manufacturers instructions and install the
supplied clip nut onto the fender on the vent rear
mounting hole.
2. Install the ION™ lighthead into the SideKick™
panel using the 2 supplied washer head screws
(Fig. 2).
©2012 Whelen Engineering Company Inc.
Form No.14577 (033012)
Page 1
For warranty information regarding this product, visi85ww.whelen.com/warranty
Connecting the Lighthead to Power:
CAUTION! DO NOT LOOK DIRECTLY AT THESE LED’S WHILE THEY ARE ON.
MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT!
IMPORTANT WARNING!
Flash Patterns / Split LED:
BOLD . /NOTE: = CA Title XIII Compliant Pattern = SYNC PatternItalic / PH = Phase
1. SignalAlert™ 75 (PH 1)
2. SignalAlert 75 (PH 2)
3. SignalAlert 75 (PH 3)
4. SignalAlert 75 (PH 4)
5. CometFlash® 75 (PH 1)
6. CometFlash 75 (PH 2)
7. CometFlash 75 (PH 3)
8. CometFlash 75 (PH 4)
17. ComAlert™ 75 (PH 1)
18. ComAlert 75 (PH 2)
19. ComAlert 75 (PH 3)
20. ComAlert 75 (PH 4)
21. LongBurst™ 75 (PH 1)
22. LongBurst 75 (PH 2)
23. LongBurst 75 (PH 3)
9. DoubleFlash 75 (PH 1)
10. DoubleFlash 75 (PH 2)
11. DoubleFlash 75 (PH 3)
12. DoubleFlash 75 (PH 4)
13. SingleFlash 75 (PH 1)
14. SingleFlash 75 (PH 2)
15. SingleFlash 75 (PH 3)
16. SingleFlash 75 (PH 4)
24. LongBurst 75 (PH 4)
29. SSNF 75 (PH 1)
30. SSNF 75 (PH 2)
25. PingPong™ 75 (PH 1)
26. PingPong 75 (PH 2)
27. PingPong 75 (PH 3)
28. PingPong 75 (PH 4)
31. SingleFlash 60 (Alt.)
32. SingleFlash 60 (Sim.)
SingleFlash (
SingleFlash 0 (Sim.)
35. SingleFlash 120 (Alt.)
36. SingleFlash 120 (Sim.)
SingleFlash 300 (Alt.)
38. SingleFlash 300 (Sim.)
DoubleFlash 150 (Alt.)
40. DoubleFlash 150 (Sim.)
41. ComAlert™ 150 (Alt.)
42. ComAlert™ 150 (Sim.)
43. ActionFlash™ 50 (Alt.)
44. ActionFlash™ 50 (Sim.)
45. ActionFlash™ 150 (Alt.)
46. ActionFlash™ 150 (Sim.)
33. 90 Alt.)
34. 9
37.
39.
47. ModuFlash™ (Alt.)
48. ModuFlash™ (Sim.)
64. ActionScan™ (Alt./Sim.)
49. DoubleFlash 120 (Alt.)
50. DoubleFlash 120 (Sim.)
51. PingPong™ 120 (Alt.)
52. PingPong 120 (Sim.)
53. TripleFlash™ 75 (Alt.)
54. TripleFlash 75 (Sim.)
55. TripleFlash 120 (Alt.)
56. TripleFlash 120 (Sim.)
57. SigAlert Cal.™ (Alt.)
58. SigAlert Cal. (Sim.)
59. Action SF 60/120 (Alt.)
60. Action SF 60/120 (Sim).
61. Action SF60/TF120 (Alt.)
62. Action SF60/TF120 (Sim.)
63. CalScan™ (Alt./Sim.)
65. SteadyFlash 60
66. SteadyFlash 75
67. SteadyFlash 90
68. SteadyFlash 120
69. Steady & Steady
SingleFlash 75PH 2
PingPong™ 75PH 1
PingPong 75PH 2
ComAlert™ 75PH 1
ComAlert 75PH 2
LongBurst™ 75PH 1
LongBurst 75PH 2
8.
9.
10.
11.
12.
13.
14.
SingleFlash 60
SingleFlash
SingleFlash 120
SingleFlash 300
DoubleFlash 150
ComAlert™ 150
ActionFlash™ 50
90
ActionFlash™ 150
ModuFlash™
ActionScan™
Steady
15.
17.
18
1
20.
21.
16.
.
9.
22.
23.
24.
25.
SignalAlert™ 75PH 1
SignalAlert 75PH 2
CometFlash® 75PH 1
CometFlash 75PH 2
DoubleFlash 75PH 1
DoubleFlash 75PH 2
SingleFlash 75PH 1
1.
2.
3.
4.
5.
6.
7.
Flash Patterns / Regular LED:
GND
SYNC
SCANLOCK
BLACK GREY WHT/VIO -
+12VSplit Lighthead: RED/WHT -
- +12VSolid Lighthead: LED COLOR
LIGHTHEAD
To Ground Terminal
To SYNC wire of other light
Flash Pattern Selection
To +12 Volts VDC
Fuse @ 3 AMPS / Customer supplied
NOTE: The positive wire will vary depending upon which lighthead you have.
CAUTION! DO NOT LOOK DIRECTLY AT THESE LED’S WHILE THEY ARE ON.
MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT!
IMPORTANT WARNING!
Flash Patterns / Split LED:
BOLD . /NOTE: = CA Title XIII Compliant Pattern = SYNC PatternItalic / PH = Phase
1. SignalAlert™ 75 (PH 1)
2. SignalAlert 75 (PH 2)
3. SignalAlert 75 (PH 3)
4. SignalAlert 75 (PH 4)
5. CometFlash® 75 (PH 1)
6. CometFlash 75 (PH 2)
7. CometFlash 75 (PH 3)
8. CometFlash 75 (PH 4)
17. ComAlert™ 75 (PH 1)
18. ComAlert 75 (PH 2)
19. ComAlert 75 (PH 3)
20. ComAlert 75 (PH 4)
21. LongBurst™ 75 (PH 1)
22. LongBurst 75 (PH 2)
23. LongBurst 75 (PH 3)
9. DoubleFlash 75 (PH 1)
10. DoubleFlash 75 (PH 2)
11. DoubleFlash 75 (PH 3)
12. DoubleFlash 75 (PH 4)
13. SingleFlash 75 (PH 1)
14. SingleFlash 75 (PH 2)
15. SingleFlash 75 (PH 3)
16. SingleFlash 75 (PH 4)
24. LongBurst 75 (PH 4)
29. SSNF 75 (PH 1)
30. SSNF 75 (PH 2)
25. PingPong™ 75 (PH 1)
26. PingPong 75 (PH 2)
27. PingPong 75 (PH 3)
28. PingPong 75 (PH 4)
31. SingleFlash 60 (Alt.)
32. SingleFlash 60 (Sim.)
SingleFlash (
SingleFlash 0 (Sim.)
35. SingleFlash 120 (Alt.)
36. SingleFlash 120 (Sim.)
SingleFlash 300 (Alt.)
38. SingleFlash 300 (Sim.)
DoubleFlash 150 (Alt.)
40. DoubleFlash 150 (Sim.)
41. ComAlert™ 150 (Alt.)
42. ComAlert™ 150 (Sim.)
43. ActionFlash™ 50 (Alt.)
44. ActionFlash™ 50 (Sim.)
45. ActionFlash™ 150 (Alt.)
46. ActionFlash™ 150 (Sim.)
33. 90 Alt.)
34. 9
37.
39.
47. ModuFlash™ (Alt.)
48. ModuFlash™ (Sim.)
64. ActionScan™ (Alt./Sim.)
49. DoubleFlash 120 (Alt.)
50. DoubleFlash 120 (Sim.)
51. PingPong™ 120 (Alt.)
52. PingPong 120 (Sim.)
53. TripleFlash™ 75 (Alt.)
54. TripleFlash 75 (Sim.)
55. TripleFlash 120 (Alt.)
56. TripleFlash 120 (Sim.)
57. SigAlert Cal.™ (Alt.)
58. SigAlert Cal. (Sim.)
59. Action SF 60/120 (Alt.)
60. Action SF 60/120 (Sim).
61. Action SF60/TF120 (Alt.)
62. Action SF60/TF120 (Sim.)
63. CalScan™ (Alt./Sim.)
65. SteadyFlash 60
66. SteadyFlash 75
67. SteadyFlash 90
68. SteadyFlash 120
69. Steady & Steady
SingleFlash 75PH 2
PingPong™ 75PH 1
PingPong 75PH 2
ComAlert™ 75PH 1
ComAlert 75PH 2
LongBurst™ 75PH 1
LongBurst 75PH 2
8.
9.
10.
11.
12.
13.
14.
SingleFlash 60
SingleFlash
SingleFlash 120
SingleFlash 300
DoubleFlash 150
ComAlert™ 150
ActionFlash™ 50
90
ActionFlash™ 150
ModuFlash™
ActionScan™
Steady
15.
17.
18
1
20.
21.
16.
.
9.
22.
23.
24.
25.
SignalAlert™ 75PH 1
SignalAlert 75PH 2
CometFlash® 75PH 1
CometFlash 75PH 2
DoubleFlash 75PH 1
DoubleFlash 75PH 2
SingleFlash 75PH 1
1.
2.
3.
4.
5.
6.
7.
Flash Patterns / Regular LED:
GND
SYNC
SCANLOCK
BLACK GREY WHT/VIO -
+12VSplit Lighthead: RED/WHT -
- +12VSolid Lighthead: LED COLOR
LIGHTHEAD
To Ground Terminal
To SYNC wire of other light
Flash Pattern Selection
To +12 Volts VDC
Fuse @ 3 AMPS / Customer supplied
NOTE: The positive wire will vary depending upon which lighthead you have.
Route the lighthead wires along the same path as the vehicle’s main power cable and
connect to power.
WARNING: All customer supplied wires that connect to the positive
terminal of the battery must be sized to supply at least 125% of the
maximum operating current and FUSED at the battery to carry that load.
DO NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT!
Operation:
Scan-Lock™ (WHT/VIO) - Note: The light must be on to change patterns.
To advance to next pattern: Apply +VDC to the WHT/VIO wire for less than 1 second.
To cycle backwards: Apply +VDC to the WHT/VIO wire for more than 1 second.
To reset to the factory default pattern: Turn off power to the light. While applying
+VDC to the WHT/VIO wire, turn the light back on. Continue to apply voltage for 5
seconds.
SYNC (GREY) - Lights configured to display the Phase 1 mode of a pattern will flash
simultaneously. Lights configured to display the Phase 2 mode will alternate with any
Phase 1 lights with the same pattern.
To sync two lights, configure both lights to display the same Phase 1 pattern. Turn power off and connect the GREY wires from each light together. When the lights are activated,
their patterns will be synchronized. To configure the two lights to alternate their patterns, advance the pattern of either lights to Phase 2 of the current pattern. The same concept
applies to Phases 3 and 4.
Connecting the Lighthead to Power:
Route the lighthead wires along the same path as the vehicle’s main power cable and
connect to power.
WARNING: All customer supplied wires that connect to the positive
terminal of the battery must be sized to supply at least 125% of the
maximum operating current and FUSED at the battery to carry that load.
DO NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT!
Operation:
Scan-Lock™ (WHT/VIO) - Note: The light must be on to change patterns.
To advance to next pattern: Apply +VDC to the WHT/VIO wire for less than 1 second.
To cycle backwards: Apply +VDC to the WHT/VIO wire for more than 1 second.
To reset to the factory default pattern: Turn off power to the light. While applying
+VDC to the WHT/VIO wire, turn the light back on. Continue to apply voltage for 5
seconds.
SYNC (GREY) - Lights configured to display the Phase 1 mode of a pattern will flash
simultaneously. Lights configured to display the Phase 2 mode will alternate with any
Phase 1 lights with the same pattern.
To sync two lights, configure both lights to display the same Phase 1 pattern. Turn power off and connect the GREY wires from each light together. When the lights are activated,
their patterns will be synchronized. To configure the two lights to alternate their patterns, advance the pattern of either lights to Phase 2 of the current pattern. The same concept
applies to Phases 3 and 4.
Page 2
Loading...