Whelen HWLRB12 User Manual

®

ENGINEERING COMPANY INC.

51 Winthrop Road
Chester, Connecticut 06412-0684
Phone: [phone]

Howler™ Siren Speaker Bracket

Installation Guide:

2011 Ford F-250 / F-350

Fax: [phone]
Internet: www.whelen.com
Sales e-mail: [e-mail]
Canadian Sales e-mail: [e-mail]
Customer Service e-mail: [e-mail]

DANGER! Sirens produce extremely loud emergency warning tones! Exposure to these tones without

proper and adequate hearing protection, could cause ear damage and/or hearing loss! The Occupational Safety &
Health Administration (www.osha.gov) provides information necessary to determine safe exposure times in
Occupational Noise Exposure Section 1910.95. Until you have determined the safe exposure times for your
specific application, operators and anyone else in the immediate vicinity should be required to wear an approved
hearing protection device. FAILURE TO FOLLOW THIS RECOMMENDATION COULD CAUSE HEARING LOSS!

Safety First

This document provides all the necessary information to allow your Whelen product to be properly and safely installed.
Before beginning the installation and/or operation of your new product, the installation technician and operator must
read this manual completely. Important information is contained herein that could prevent serious injury or damage.

• Proper installation of this product requires the installer to have a good understanding of automotive electronics,
systems and procedures.

• Failure to use specified installation parts and/or hardware will void the product warranty!

• If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or other
vital parts could be damaged by the drilling process. Check both sides of the mounting surface before drilling
begins. Also de-burr any holes and remove any metal shards or remnants. Install grommets into all wire
passage holes.

• If this manual states that this product may be mounted with suction cups, magnets, tape or Velcro®, clean the
mounting surface with a 50/50 mix of isopropyl alcohol and water and dry thoroughly.

• Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted or
located in the air bag deployment area will damage or reduce the effectiveness of the air bag, or become a
projectile that could cause serious personal injury or death. Refer to your vehicle owner’s manual for the air bag
deployment area. The User/Installer assumes full responsibility to determine proper mounting location, based
on providing ultimate safety to all passengers inside the vehicle.

• For this product to operate at optimum efficiency, a good electrical connection to chassis ground must be
made. The recommended procedure requires the product ground wire to be connected directly to the NEGATIVE
(-) battery post.

• If this product uses a remote device to activate or control this product, make sure this control is located in an
area that allows both the vehicle and the control to be operated safely in any driving condition. DO NOT
ATTEMPT TO ACTIVATE OR CONTROL THIS DEVICE IN A HAZARDOUS DRIVING SITUATION.

• It is recommended that these instructions be stored in a safe place and
referred to when performing maintenance and/or reinstallation of this
product.

• FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND
INSTRUCTIONS COULD RESULT IN DAMAGE TO THE PRODUCT OR
VEHICLE AND/OR SERIOUS INJURY TO YOU AND YOUR PASSENGERS!

ACTIVATION OF THIS
SIREN MAY DAMAGE
UNPROTECTED EARS!

CAUTION

Loud siren noise can cause
hearing damage and/or loss.

Wear

Refer to OSHA Section 1910.95 prior

Protection!

to putting ANY siren into service!

Automotive: Sirens/Switches

For warranty information regarding this product, visit www.whelen.com/warranty

©2011 Whelen Engineering Company Inc.
Form No.14477 (032411)

Page 1

IMPORTANT! READ THESE WARNINGS BEFORE CONTINUING!

The Howler™ Supplemental Siren was designed for use in high-risk areas such as an intersection. It is not intended to be, nor should be
operated as a replacement or alternative to the vehicle’s primary siren.

The low-frequency tones of the Howler™ demonstrate significantly different audio characteristics as compared to those of a traditional higher­frequency siren. While the low-frequency tones are better able to penetrate other vehicles, thus alerting drivers to the presence of the
responding emergency vehicle, these tones may also penetrate into the responding vehicle itself. This could potentially expose the operator to
increased noise levels.

To help eliminate overexposure, the Howler™ siren has been designed with a built-in timing circuit. The Occupational Safety & Health
Administration (OSHA) (www.osha.gov) provides information necessary to determine safe exposure times in Noise and Hearing Conservation,
Section 1910.95 (Occupational Noise Exposure). Until you have determined the safe exposure times for your specific application, this siren
should be configured for the minimum operating time and operators should be required to use an approved hearing protection device.
FAILURE TO FOLLOW THIS RECOMMENDATION COULD CAUSE HEARING LOSS!

Installation:

1. This bracket will mount to the
frame using existing mounting
hardware. Remove the 2 bolts
from the vehicle, shown in figure

1.

2. Secure the support bracket to the
siren speaker using the supplied
mounting hardware and tighten
firmly (See illustration).

3. Next, secure the mounting
bracket to the siren speaker and
also to the support bracket using
the supplied hardware and tighten
firmly.

4. Holding the siren speaker in
place, line up the 2 holes in the
mounting bracket with the 2 holes
in the vehicle frame where you
removed the bolts in step 1 and
re-insert the 2 bolts.

5. Tighten the 2 bolts firmly and the installation
is complete (Fig. 2).

6. Extend the WHITE (positive) and BLACK (negative) speaker wires to your
siren amplifier and refer to the amplifiers instructions for connections.

IMPORTANT! It is the responsibility of the installation technician to make
sure that the installation and operation of this product will not interfere with or
compromise the operation or efficiency of any vehicle equipment!

IMPORTANT! Before returning the vehicle to active service, visually confirm
the proper operation of this product, as well as all vehicle components/
equipment.

Passenger side shown

Securing speaker
to mounting
bracket

5/16 -18 X
1-1/4 Hex
Head Bolt

Mounting

Strap

Bottom of
mounting strap

5/16 - 18
Elastic
Stop Nut

5/16 Flat
Washer

SPEAKER

Spacer

Mounting
Bracket

bracket slides

ounting

m

ounting

M

een

betw

5/16 -18 X 1-3/4
Hex Head Bolt

straps

5/16 Flat
Washer

5/16 - 18
Elastic
Stop Nut

Mounting

Existing

Hardware

1/4-20

ELASTIC

STOP NUT

Bracket

1/4" FLAT
WASHER

vehicle

Support
Bracket

1/4-20X1
HEX HD
CAP SCREW

5/16 X 1 HEX
HEAD SHEET
METAL SCREW

Page 2