Whelen DBKT5 User Manual
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
®
Installation Guide:
Dominator™ Rear Window Bracket DBKT5
2008 Tahoe
Internet: www.whelen.com
Sales e-mail: autosale@whelen.com
Canadian Sales e-mail: autocan@whelen.com
Customer Service e-mail: custserv@whelen.com
R
Fig. 1
Caution: Permanent mounting of this product will require drilling. It
is absolutely necessary to make sure that no other vehicle
components could be damaged by this process. Check both sides of
the mounting surface before starting.
1. Lower the rear section of the headliner and locate the 2 existing holes
2. Enlarge these holes to a diameter of .391” using an appropriately
IMPORTANT NOTE! This installation uses Rivnuts™ to secure the
brackets to the vehicle. This type of hardware requires the use of a
specialized installation tool. Refer to the owners manual included
with this tool for proper installation techniques. Be sure to follow the
mounting hole specifications precisely!
3. Secure tighten the two brackets to the two Rivnuts using the supplied
Automotive: Lightbars
©2008 Whelen Engineering Company Inc.
Form No.14247 (120208)
Top view of vehicle shows approximate of mounting holeslocation
in the vehicle roof shown in Figs. 1 & 2.
sized drill bit.
metal screws and lock washers.
REAR DECK
ROOF
For warranty information regarding this product, visit www.whelen.com/warranty
W
O
D
N
I
W
R
A
E
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
TRUNK
Mount
here
Headliner covers this area
R
EA
R
W
IND
O
W
4. Replace the headliner
and make two small slits
in the headliner for the
brackets to go through.
5. Secure the lightbar to the
two brackets.
6. Extend the lightbar wires to your power source and connect the wires
as shown in the lightbar manual.
IMPORTANT! Before returning the vehicle to active service, visually
confirm the proper operation of this product, as well as all vehicle
components/equipment.
®
Installation Guide:
Fig. 2
Dominator™ Rear Window Bracket DBKT5
2008 Tahoe
Internet: www.whelen.com
Sales e-mail: autosale@whelen.com
Canadian Sales e-mail: autocan@whelen.com
Customer Service e-mail: custserv@whelen.com
R
Fig. 1
Caution: Permanent mounting of this product will require drilling. It
is absolutely necessary to make sure that no other vehicle
components could be damaged by this process. Check both sides of
the mounting surface before starting.
1. Lower the rear section of the headliner and locate the 2 existing holes
2. Enlarge these holes to a diameter of .391” using an appropriately
IMPORTANT NOTE! This installation uses Rivnuts™ to secure the
brackets to the vehicle. This type of hardware requires the use of a
specialized installation tool. Refer to the owners manual included
with this tool for proper installation techniques. Be sure to follow the
mounting hole specifications precisely!
3. Secure tighten the two brackets to the two Rivnuts using the supplied
Automotive: Lightbars
©2008 Whelen Engineering Company Inc.
Form No.14247 (120208)
Top view of vehicle shows approximate of mounting holeslocation
in the vehicle roof shown in Figs. 1 & 2.
sized drill bit.
metal screws and lock washers.
REAR DECK
ROOF
For warranty information regarding this product, visit www.whelen.com/warranty
W
O
D
N
I
W
R
A
E
TRUNK
Page 1
Fig. 2
Mount
here
Headliner covers this area
R
EA
R
W
IN
D
O
W
4. Replace the headliner
and make two small slits
in the headliner for the
brackets to go through.
5. Secure the lightbar to the
two brackets.
6. Extend the lightbar wires to your power source and connect the wires
as shown in the lightbar manual.
IMPORTANT! Before returning the vehicle to active service, visually
confirm the proper operation of this product, as well as all vehicle
components/equipment.
MOUNTING
BRACKET
BASE
EXTRUSION
DISK GASKET
#10 .631 DIA. X .060
FLAT WASHER
#10-24
ELASTIC
STOP NUT
End view of extrusion with endcap removed.
Fig. 3
Slide
other
to
side
of
extrusion
E
A-B-1/4" Internal Tooth Lock Washer
1/4 - 20 X 1 PPHMS
#10-24 Elastic Stop Nut
C-
#10 .631 Dia. X .060 Flat Washer
D-
Installed Rivnut
E-
10-24 X 5/8" Carraige Bolt
F-
Disk Gasket
G-
C
E
D
A
C
B
G
F
D
MOUNTING
BRACKET
BASE
EXTRUSION
DISK GASKET
#10 .631 DIA. X .060
FLAT WASHER
#10-24
ELASTIC
STOP NUT
End view of extrusion with endcap removed.
Fig. 3
Slide
other
to
side
of
extrusion
E
A-B-1/4" Internal Tooth Lock Washer
1/4 - 20 X 1 PPHMS
#10-24 Elastic Stop Nut
C-
#10 .631 Dia. X .060 Flat Washer
D-
Installed Rivnut
E-
10-24 X 5/8" Carraige Bolt
F-
Disk Gasket
G-
Page 2
C
E
D
A
C
B
G
F
D
Loading...