Whelen 9061211 User Manual
.25
2.01"
1.77"
12.0" ±1.0"
.98 REF
5.61"
1
2
3
4
5
6
7
8
9
Ac
AC2
AC3
AC4
AC5
C6
-
1
V+
A
Cathode
Anti-Collision Light
Anti-Collision Light
Anti-Collision Light
Anti-Collision Light
V IN
Anti-Collision Light
Anti-Collision Light
FWD & AFT Position Lights
Not Used
20 AWG
20 AWG
20 AWG
20 AWG
18 AWG
20 AWG
20 AWG
20 AWG
20 AWG
CPC 206485-1 22759/43 WIRES
®
MADE IN THE U.S.A.
ENGINEERING COMPANY INC.
51 Winthrop Road
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-2009
Internet: www.whelen.com
Sales/Service e-mail: aviation@whelen.com
TSO-C30c
TYPE I, II & III;
APPROVED
TSO-C96a
CLASS I;
APPROVED
EQUIPMENT LIMITATIONS:
An approved lighting system consists of two lights, one located
on each wingtip. The baseplate must be mounted parallel to
the vertical and horizontal centerlines of the aircraft to project
the patterns properly. A separate flasher assembly, such as
model 7145702, is required for each light assembly.
Certain types of installations may require additional testing.
CONTINUED AIRWORTHINESS:
The forward position light is designed with 4 Green LEDs or 5
Red LEDs. The tail position light is designed with 2 LEDs. The
anti-collision light is designed with 36 LEDs.
If any one bank of LEDs fails, the flasher module should be
checked. If module checks good, replace the lighthead. If any
one LED fails, the unit must be repaired or replaced.
Note: To reduce eye strain, use an optical filter such as dark
glasses or a blue covering dome during LED inspection.
Inspect the lens. Replace if there is excessive scratching,
pitting, discoloration or cracking.
Note: The anti-collision light will automatically shut-off after 910 flashes if a failure is detected by flasher assembly model
7145702.
INSTALLATION PROCEDURES:
The following information is to assist you in installing a Whelen
light system. The installation procedure described in the
following text will be confined to a single light installation, but is
identical for multiple light installations.
Installation Guide:
Aviation model 9061211, 9061212
P/N 01-0790612-11, 01-0790612-12
LED Position / Anti-Collision
Light Assembly
The conditions and tests required for TSO approval of this
article are minimum performance standards. It is the
responsibility of those installing this article either on or within
a specific type or class of aircraft to determine that the aircraft
installation conditions are within the TSO standards. TSO
articles must have separate approval for installation in aircraft.
The article may be installed only if performed under 14 CFR
part 43 or the applicable airworthiness requirements.
6. Waterproof the lightbase to aircraft. Apply single-part
Silicone (RTV) or equivalent around any open area
where water could get in.
7. Check all avionics systems for interference from this
installation.
8. A flight check should be performed by a properly
certified pilot.
9. Update aircraft records, complete Form 337 and obtain
FAA field approval for installation, as required.
1. Choose the appropriate Model 90612( ) light assembly.
2. Using the mounting detail information on page 2, prepare
the aircraft for means to secure the LED light assembly.
Aviation
Remove any existing mounting adapters.
3. Connect the light inputs according to the chart shown.
Connections to be in accordance with FAA approved
methods.
4. Remove the lens retainers and carefully remove the lens.
Using appropriate hardware, install the light assembly and
insure that all leads are clear of any obstructions. Ty-rap
as required. Secure the light assembly using vibration
resistant threaded fasteners.
5. Carefully reinstall the lens and retainers.
©2012 Whelen Engineering Company Inc.
Form No.14603 (062112)
Page 1
55
11
11
111
1
1
1
2
1
1
1
2
ITEM PART NUMBER DESCRIPTION
ASS'Y, GREEN POS. / ANTI-COLLISION LIGHT
ASS'Y, RED POS. / ANTI-COLLISION LIGHT
RETAINER, REAR
RETAINER, FRONT
SCREW, 4-40 X 5/16 PFHMS 100° C'sk
SCREW, 2-56 X 1/4 P82FHMS SS w/NYLON
SCREW, 4-40 X 7/16 PFHMS 100° C'sk
LENS, HARDCOATED
GASKET, LENS
SHROUD, TAIL POSITION LIGHT
SHROUD, FORWARD POSITION LIGHT
REFLECTOR, 90°
Threadlocker, 242 Loctite 50ml
ASS'Y, LIGHTHEAD MODEL 9061211, GREEN
ASS'Y, LIGHTHEAD MODEL 9061212, RED
BASE PLATE
01-0790612-11
01-0790612-12
19-151003-100
19-171471-100
14-0050581B03
14-0050581-05
68-3990574A30
38-0231219-00
11-651008-000
11-651016-000
14-026116-04M
68-5451007-00
66-0715403-00
01-0271597-11
01-0271597-12
QTYQTY
-1
-
1
A/R
1
1
A/R
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
11
06-171472-200
MOUNTING DETAIL
1.000
4.500
REFERENCE TYP MOUNTING HOLE
FOR #6, 100° C'SINK
Ø1.10 REF
.575
.288
2.09
.59
.500
1
2
3
4
9
6
7
8
6
11 12
10
5
13
1
14
Page 2
Loading...