Whelen 90193 User Manual
1.08
1.03
2.46
3.450
DIMENSIONS
MODEL 90193 - ( )
1.79
ENGINEERING COMPANY INC.
(
)
y
)
g
y
ROUTE 145, WINTHROP ROAD
CHESTER, CONNECTICUT 06412-0684
TELEPHONE:
860) 526-9504
FAX: (860) 526-4078
MADE IN THE U.S.A.
Installation Guide for Model 90193 - (
Anti-Collision / Position Light Assembl
FAA / TSO C30b TYPE 1 & 2
and
FAA / TSO - C96a
APPROVED
Model 90193 - (
Anti-Collision / Position
ht Assembl
Li
SPECIFICATIONS:
Nominal Operational Voltage:........................................ 28 VDC
Average Input Current: .....................................................1 AMP
Lamp for all Units:....................................28VDC, 26 Watts Max.
EQUIPMENT LIMITATIONS:
An approved Anti-Collision / Position System consists of two
assemblies, one located on each wingtip.
INSTALLATION PROCEDURES: The following information is to
assist you in installing a Whelen Anti-Collision / Position light
system.
1) Choose the appropriate Model 90193 - ( ) replacement light
assembly.
2) The installation procedure described in the following text will
be confined to a single light installation, but is identical for
multiple light instal lat ion .
3) Remove old anti-collision light, locate and record existing
+28 VDC and (-) ground terminal block position and output
connector from power supply.
4) Use existing mounting holes and hardware.
5) Connect leads from light assembly to terminal block in
recorded manner and lead from light to power supply.
6) Breaker
Make sure existing system is equipped with an appropriate
sized breaker.
7) Install light assembly and insure that all leads are clear of any
obstructions and ty-rap as required. Secure light assembly,
use lock was hers a nd/or th read lo c k, on all threade d f ast eners .
Requirements
8) Check all avionics systems for interference from this
installation.
9) A flight check should be performed by a properly certified
pilot.
10) When necessary, waterproof the light assembly to aircraft.
Apply single part silicone (RTV) or equivalent around any
open area where water could get in.
11) Update aircraft records and complete Form 337.
12) Obtain FAA field approval for installation.
©1998 Whelen Engineering Company Inc.
Form No.13302A (021198)
99
1.41 DIA. .984 DIA.
3
.785
MOUNTING PLAN
2.040
C
L
1.181
2.3621.570
5
6
7
8
4
.748
2
2.040
.149 DIA.
(4) PLACES
90193-()PARTS LIST
ITEM PART NUMBER
#6-32 X 5/16 100°CSK PFHMS
9
GASKET (W1283)
8
LAMP, 28V (W1290-28)
7
LENS, RED (W1284-R)
6
LENS, GREEN (W1284-G)
5
GASKET, FLASHTUBE JPAT (.250 THK)
4
RETAINER/LENS ASSEMBLY
3
FLASHTUBE ASSEMBLY
2
BASE PLATE ASSEMBLY, WINGTIP LT
1
ANTI-COLL/POSITION LT. ASSY. (RED)
ANTI-COLL/POSITION LT. ASSY. (GREEN)
DESCRIPTION
14-0050563-25
38-0230021-00
34-0428020-65
68-4230020-50
68-4230020-40
38-0130878-00
02-0350667-35
36-0050652-00
02-0350665-00
01-0790193-01
01-0790193-00
1
90193 - ( )
ANTI COLLISION / POSITION
LIGHT ASSEMBLY
MS 3116F10-6P
CONNECTOR WIRING
POS A - ANODE
- TRIGGER
POS B
- (+) POSITION LT
POS C
- CATHODE
POS D
- N/C
POS E
- (-) POSITION LT
POS F
Loading...