Whelen 9008811 User Manual
®
ENGINEERING COMPANY INC.
Route 145, Winthrop Road,
Chester, Connecticut 06412
Phone: (860) 526-9504
Fax: (860) 526-2009
Internet: www.whelen.com
Sales/Service e-mail: aviation@whelen.com
OPERATING INSTRUCTIONS:
Operational Voltage:. . . . . .28 VDC (nominal)
Average Input Current:. . . .0.56 Amps / 3 Amps Peak @ .25 Sec.
The conditio ns and te sts requ ired for TSO app roval of th is articl e
are minimum performance standards. It is the responsibility of
those installing this article either on o r within a specific type or
class of aircraft to determine that the aircraft installation
conditions are within the TSO standards. TSO articles must have
separate approval for installation in aircraft. The article may be
installed only if performed under 14 CFR part 43 or the applicable
airworthiness requirements.
CONTINUED AIRWORTHINESS: The 90088 series led anti-collision
light assembly is designed with 2 banks of 7 leds. Should any one led or
bank fail, the unit must be repaired or replaced. Inspect the lens for
excessive scratches or pitting. Replace if necessary.
EQUIPMENT LIMITATIONS: The ClassiIII anti-collision system must
produce a minimum of 100 effective candelas in aviation red or white,
360° around the vertical axis. A sing le beacon on the topside of the
fuselage and a single beacon on the underside of the fuselage will meet
this requirement.
INSTALLATION PROCEDURES: The following information is t o assist
in the installation of a Whelen LED Anti-Collision Light Assembly.
1. Choose the appropriate 90088( ) replacement light assembly
which is most applicable to your aircr aft. Lower mounts have a
drain hole in the lens.
2. The installation procedure described in the following text will be
confined to a single light installation, but is identical for multiple
light installations.
3. Remove old light, locate and save the existin g +28VDC lead and
(-) ground lead. Clean and prep lead ends as required.
4. Use existing mounting holes and hardware.
5. Connect the +28 VDC and (-) ground leads equipped with an
appropriate sized breaker to the LED Light. Both lead s must be
connected by an approved FAA connection.
6. Install light assembly and ins ure that the wire leads are clear of
any obstructions and ty-wrap a s required. Us e lock washer s and/
or thread lock on all threaded fasteners.
7. Check all avionics systems for interference from the installation.
8. A flight check should be performed by a properly certified pilot.
9. Update aircraft records, complete For m 337 and obtain FAA field
approval for installation.
Aviation
MADE IN THE U.S.A.
TSO-C96a
CLASS III
APPROVED
Installati on Guide:
Model 90088( )-series
Models 9008811, 9008812, 9008813,
9008814, 9008815, 9008816
P/N:01-0790088-11, 01-0790088-12,
01-0790088-13, 01-0790088-14
01-0790088-15, 01-0790088-16
LED Anti-Collision Light Assembly
Model(s):
01-0790088-11, 01-0790088-12, 01-0790088-14
2.38
2.70
.80
1.84
18.00"±1.00"
2/C Shielded Cable
#M27500-20TE2T14
Model(s):
01-0790088-13
2.38
2.70
.80
1.84
8.00"±.50"
2/C Shielded Cable
#M27500-20TE2T14
Model(s):
01-0790088-15, 01-0790088-16
2.38
2.70
.80
.38
1.84
Receptacle - MS27508E10A-5P
POS A - +28VDC
POS B - GROUND
Model(s):
All
8.880
6.700
1.95
.670
.936
1.70
SUGGESTED MOUNTING PATTERN
5.00
.90 TYP
9.87
4.86
WHITE/BLUE - (+28 VDC)
WHITE - (-)GROUND
SHIELD
9.87
4.86
WHT/BLUE-+28V
WHT-GROUND
BRAIDSHIELD
1234
AMP #1-480703-0
Connector Wiring
POS 1 - WHT/BLUE - +28V
POS 2 - WHITE - GND
POS 3 - SHIELD
POS 4 - N/C
9.87
1.20
4.86
POSC-N/C POSE-N/C
POSD-N/C
Drain Hole
(Model -11)
Drain Hole
(Models -12
& -14)
Drain Hole
Drain Hole
(-15 Model)
Drain Hole
.203 DIA.
MNTG HOLES
(5 PLACES)
6(-1 Model)
©2005 Whelen Engineering Company Inc.
Form No.14002B (060606)
Page 1
Models:
9008811, 9008812, 9008814
Model:
9008813
Models:
9008815, 9008816
111
222
444
333
555
778
6
9
Input Wires
White/Blue - (28VDC) White/Blue - (28VDC)
White - (-)Ground White - (-)Ground
Shield Shield
(as used on models
,&
9008811 9008812
9008814)
10 10
9
Input Wires
1
2
3
4
(as used on model
3
900881 )
9
Input Connector
(as used on models
&
9008815 9008816)
1211
ITEM PART NUMBER DESCRIPTION
01-0771021-11
01-0771021-12
01-0771021-13
01-0771021-14
01-0771021-15
01-0771021-16
1
2222
2
1
1
1
1
1
1
1
1
1
19-171019-00S
2
68-4270579-30
3
4
68-4270579-31
38-0270584-00
5
01-0271022-01
611
01-0271022-02
7
01-0271022-03
8
38-0270864-00
9
14-0050509-15
10
39-0404014-14
11
39-0500315-18
12
9008811 Final Assembly (Lower Mount)
9008812 Final Assembly (Upper Mount)
9008813 Final Assembly (Upper Mount)
9008814 Final Assembly (Upper Mount)
9008815 Final Assembly (Lower Mount)
9008816 Final Assembly (Upper Mount)
#10-32 X ½ Phillips FHMS
Lens Retainer - polished (w/seal)
Lens (clear)
Lens (w/drain hole (clear))
Lens Gasket
LED Assembly (90088-series)
LED Assembly (90088-series)
LED Assembly (90088-series)
Baseplate Gasket
Screw #4-40 X 3/8 PFH MS51959-15
4-Pos. Pin Housing (Mate-N-Lok)
Pin, 20-14 AWG, .084 (Mate-N-Lok)
1
1
1
1
1
QTYQTYQTY QTY QTY QTY
2
1
111
1
11
1
111
11
1
11
1
3
Page 2
Loading...